Tributary confluences and discontinuities in channel form and sediment texture: Rio Chama,NM

Numerous morphological changes can occur where two channels of distinct sediment and flow regimes meet, including abrupt shifts in channel slope, cross‐sectional area, planform style, and bed sediment size along the receiving channel. Along the Rio Chama between El Vado and Abiquiu Dams, northern New Mexico, arroyo tributaries intermittently deliver sediment from erodible sandstone and shale canyon walls to the mainstem channel. Much of the tributary activity occurs in flash floods and debris flows during summer thunderstorms, which often load the channel with sand and deposit coarser material at the mainstem confluence. In contrast, mainstem channel flow is dominated by snowmelt runoff. To examine tributary controls, we systematically collected cross‐section elevation and bed sediment data upstream and downstream of 26 tributary confluences along a 17 km reach. Data from 203 cross‐sections were used to build a one‐dimensional hydraulic model for comparing estimated channel parameters at bankfull and low‐flow conditions at these sites As compared to intermediate reaches, confluences primarily impact gradient and bed sediment size, reducing both parameters upstream of confluences and increasing them downstream. Cross‐section area is also slightly elevated above tributary confluences and reduced below. Major shifts in slope and bed sediment size at confluences appear to drive variations in sediment entrainment and transport capacity and the relative storage of sand along the channel bed. The data were analyzed and compared to models of channel organization based on lateral inputs, such as the Network Variance Model and the Sediment Link Concept. At a larger scale, hillslope ? channel coupling increases in the downstream third of the study reach, where the canyon narrows, resulting in steeper slopes and more continuous coarse bed material along the mainstem, and thus, limiting the contrast with tributary confluences. However, channel form and sediment characteristics are highly variable along the study reach, reflecting variations in the size and volume of sediment inputs related to the surface geology in tributary watersheds, morphology of the Rio Chama at the junction (i.e. bends, confinement), and the relative magnitude and location of past depositional events. Copyright © 2014 John Wiley & Sons, Ltd.     

Controls on knickpoint migration in a drainage network of the moderately uplifted Ardennes Plateau,Western Europe

Much research has been devoted to the development of numerical models of river incision. In settings where bedrock channel erosion prevails, numerous studies have used field data to calibrate the widely acknowledged stream power model of incision and to discuss the impact of variables that do not appear explicitly in the model's simplest form. However, most studies have been conducted in areas of active tectonics, displaying a clear geomorphic response to the tectonic signal. Here, we analyze the traces left in the drainage network 0.7 My after the Ardennes region (western Europe) underwent a moderate 100–150 m uplift. We identify a set of knickpoints that have traveled far upstream in the Ourthe catchment, following this tectonic perturbation. Using a misfit function based on time residuals, our best fit of the stream power model parameters yields m = 0.75 and K = 4.63 × 10^‐8 m^‐0.5y^‐1. Linear regression of the model time residuals against quantitative expressions of bedrock resistance to erosion shows that this variable does not correlate significantly with the residuals. By contrast, proxies for position in the drainage system prove to be able to explain 76% of the residual variance. High time residuals correlate with knickpoint position in small tributaries located in the downstream part of the Ourthe catchment, where some threshold was reached very early in the catchment's incision history. Removing the knickpoints stopped at such thresholds from the data set, we calculate an improved m = 0.68 and derive a scaling exponent of channel width against drainage area of 0.32, consistent with the average value compiled by Lague for steady state incising bedrock rivers. Copyright © 2014 John Wiley & Sons, Ltd.     

Impact of wastewater discharge on the channel morphology of ephemeral streams

The impact of wastewater flow on the channel bed morphology was evaluated in four ephemeral streams in Israel and the Palestinian Territories: Nahal Og, Nahal Kidron, Nahal Qeult and Nahal Hebron. Channel changes before, during and after the halting of wastewater flow were monitored. The wastewater flow causes a shift from a dry ephemeral channel with intermittent floods to a continuous flow pattern similar to that of humid areas. Within a few months, nutrient‐rich wastewater flow leads to rapid development of vegetation along channel and bars. The colonization of part of the active channel by vegetation increases flow resistance as well as bank and bed stability, and limits sediment availability from bars and other sediment stores along the channels. In some cases the established vegetation covers the entire channel width and halts the transport of bed material along the channel. During low and medium size flood events, bars remain stable and the vegetation intact. Extreme events destroy the vegetation and activate the bars. The wastewater flow results in the development of new small bars, which are usually destroyed by flood flows. Due to the vegetation establishment, the active channel width decreases by up to 700 per cent. The deposition of fine sediment and organic material changed the sediment texture within the stable bar surface and the whole bed surface texture in Nahal Hebron. The recovery of Nahal Og after the halting of the wastewater flow was relatively fast; within two flood seasons the channel almost returned to pre‐wastewater characteristics. The results of the study could be used to indicate what would happen if wastewater flows were introduced along natural desert streams. Also, the results could be used to predict the consequences of vegetation removal as a result of human intervention within the active channel of humid streams. Copyright © 2001 John Wiley & Sons, Ltd.     

Bed‐material transport estimated from channel morphodynamics: Chilliwack River,British Columbia

This study investigates the relation between channel changes, as mapped from aerial photography, and bed‐material transport along Chilliwack River, British Columbia. Detailed mapping of channel features was completed for five dates between 1952 and 1991 using an analytical stereoplotter. Data were transferred to a geographic information system (GIS) to analyse changes during four consecutive periods. Erosion and deposition volumes along channel reaches were estimated by multiplying measured areal changes by the bed‐material depth along each reach. Bed‐material transport rates are related to morphologic changes using a sediment budget approach. The highest rate of transport for the four study periods is estimated as 55 000 ± 10 000 m³ a⁻¹ between 1983 and 1991. These rates are compared with estimates from short‐term (1–2 year) changes along the lower reach to investigate variations in sediment flux that may otherwise remain undetected. Significant morphologic change occurs roughly once every 5 years when flows are large enough to erode and entrain large volumes of bed material stored within the contemporary floodplain. In the absence of large floods, transport rates decline and vegetation begins to establish new floodplain. Copyright © 2000 John Wiley & Sons, Ltd.     

Longitudinal distributions of river flood power: the combined automated flood,elevation and stream power (CAFES) methodology

Stream power can be an extremely useful index of fluvial sediment transport, channel pattern, river channel erosion and riparian habitat development. However, most previous studies of downstream changes in stream power have relied on field measurements at selected cross‐sections, which are time consuming, and typically based on limited data, which cannot fully represent important spatial variations in stream power. We present here, therefore, a novel methodology we call CAFES (combined automated flood, elevation and stream power), to quantify downstream change in river flood power, based on integrating in a GIS framework Flood Estimation Handbook systems with the 5 m grid NEXTMap Britain digital elevation model derived from IFSAR (interferometric synthetic aperture radar). This provides a useful modelling platform to quantify at unprecedented resolution longitudinal distributions of flood discharge, elevation, floodplain slope and flood power at reach and basin scales. Values can be resolved to a 50 m grid. CAFES approaches have distinct advantages over current methodologies for reach‐ and basin‐scale stream power assessments and therefore for the interpretation and prediction of fluvial processes. The methodology has significant international applicability for understanding basin‐scale hydraulics, sediment transport, erosion and sedimentation processes and river basin management. Copyright © 2008 John Wiley & Sons, Ltd.     

Coarse sediment supply sets the slope of bedrock channels in rapidly uplifting terrain: Field and topographic evidence from eastern Taiwan

The incision rate and steepness of bedrock channels depend on water discharge, uplift rate, substrate lithology, sediment flux, and bedload size. However, the relative role of these factors and the sensitivity of channel steepness to rapid (>1 mm yr⁻¹) uplift rates remain unclear. We conducted field and topographic analyses of fluvial bedrock channels with varying channel bed lithology and sediment source rock along the Coastal Range in eastern Taiwan, where uplift rates vary from 1.8 to 11.8 mm yr⁻¹ and precipitation is relatively consistent (1.5–2.7 m yr⁻¹), to evaluate the controls on bedrock channel steepness. We find that channel steepness is independent of rock uplift rate and annual precipitation but increases monotonically with sediment size and substrate strength. Furthermore, in reaches with uniform substrate lithology (mudstone and flysch), channel steepness systematically varies with sediment source rock but not with channel width. When applied to our data, a mechanistic incision model (saltation-abrasion model) suggests that the steepness of Coastal Range channels is set primarily by coarse-sediment supply. We also observe that larger particles are mainly composed of resistant lithologies derived from volcanic rocks and conglomerates. This result implies that hillslope bedrock properties in the source area exert a dominant control on the steepness of proximal channels through coarse-sediment production in this setting. We propose that channel steepness may be insensitive to uplift rate and flow discharge in fast-uplifting landscapes where incision processes are set by coarse sediment size and supply. Models assuming a proportionality between incision rate and basal shear stress (stream power) may not fully capture controls on fluvial channel profiles in landslide-dominated landscapes. Processes other than channel steepening, such as enhanced bedload impacts and debris-flow scour, may be required to balance rock uplift and incision in these transport-limited systems.     

Morphological responses and sediment processes following a typhoon‐induced dam failure,Dahan River,Taiwan

The rates and styles of channel adjustments following an abrupt and voluminous sediment pulse are investigated in the context of site and valley characteristics and time‐varying sediment transport regimes. Approximately 10.5 x 10⁶ m³ of stored gravel and sand was exposed when Barlin Dam failed during Typhoon WeiPa in 2007. The dam was located on the Dahan River, Taiwan, a system characterized by steep river gradients, typhoon‐ and monsoon‐driven hydrology, high, episodic sediment supply, and highly variable hydraulic conditions. Topography, bulk sediment samples, aerial photos, and simulated hydraulic conditions are analyzed to investigate temporal and spatial patterns in morphology and likely sediment transport regimes. Results document the rapid response of the reservoir and downstream channel, which occurred primarily through incision and adjustment of channel gradient. Hydraulic simulations illustrate how the dominant sediment transport regime likely varies between study periods with sediment yield and caliber and with the frequency and duration of high flows. Collectively, results indicate that information on variability in sediment transport regime, valley configuration, and distance from the dam is needed to explain the rate and pattern of morphological changes across study periods. Copyright © 2013 John Wiley & Sons, Ltd.     

The potential use of pollen in the identification of suspended sediment sources

Pollen and spores form a significant part of the suspended organic load of a New Forest stream. Flood concentrations reach 230 grains ml^?1 while baseflow carries under one grain ml^?1. Hydrographs from different seasons show differing hysteretic loops for pollen and spore concentrations against discharge and suspended sediment. These variations reflect not only factors of production, but the type and distance of the contributing sources. This investigation suggests that variations in flood pollen and spore concentrations may be used to trace such suspended sediment sources as: eroding bedrock, channel banks, or hillslopes under specific vegetation covers.     

Flow energy and channel adjustments in rills developed in loamy sand and sandy loam soils

The storms usually associated with rill development in nature are seldom prolonged, so development is often interrupted by interstorm disturbances, e.g. weathering or tillage. In laboratory simulated rainfall experiments, active rill development can be prolonged, and under these conditions typically passes through a period of intense incision, channel extension and bifurcation before reaching quasi‐stable conditions in which little form change occurs. This paper presents laboratory experiments with coarse textured soils under simulated rainfall which show how channel adjustment processes contribute to the evolution of quasi‐stability. Newly incised rills were stabilized for detailed study of links between rill configuration and flow energy. On a loamy sand, adjustment towards equilibrium occurred due to channel widening and meandering, whereas on a sandy loam, mobile knickpoints and chutes, pulsations in flow width and flow depth and changes in stream power and sediment discharge occurred as the channel adjusted towards equilibrium. The tendency of rill systems towards quasi‐stability is shown by changes in stream power values which show short‐lived minima. Differences in energy dissipation in stabilized rills indicate that minimization of energy dissipation was reached locally between knickpoints and at the downstream ends of rills. In the absence of energy gradients in knickpoints and chutes, stabilized rill sections tended toward equilibrium by establishing uniform energy expenditure. The study confirmed that energy dissipation increased with flow aspect ratio. In stabilized rills, flow acceleration reduced energy dissipation on the loamy sand but not on the sandy loam. On both soils flow deceleration tended to increase energy dissipation. Understanding how rill systems evolve towards stability is essential in order to predict how interruptions between storms may affect long‐term rill dynamics. This is essential if event‐based physical models are to become effective in predicting sediment transport on rilled hillslopes under changing weather and climatic conditions. Copyright © 2008 John Wiley and Sons, Ltd.     

Processes and forms of an unstable alluvial system with resistant,cohesive streambeds

As a response to channelization projects undertaken near the turn of the 20th century and in the late 1960s, upstream reaches and tributaries of the Yalobusha River, Mississippi, USA, have been rejuvenated by upstream‐migrating knickpoints. Sediment and woody vegetation delivered to the channels by mass failure of streambanks has been transported downstream to form a large sediment/debris plug where the downstream end of the channelized reach joins an unmodified sinuous reach. Classification within a model of channel evolution and analysis of thalweg elevations and channel slopes indicates that downstream reaches have equilibrated but that upstream reaches are actively degrading. The beds of degrading reaches are characterized by firm, cohesive clays of two formations of Palaeocene age. The erodibility of these clay beds was determined with a jet‐test device and related to critical shear stresses and erosion rates. Repeated surveys indicated that knickpoint migration rates in these clays varied from 0·7 to 12 m a^?1, and that these rates and migration processes are highly dependent upon the bed substrate. Resistant clay beds of the Porters Creek Clay formation have restricted advancement of knickpoints in certain reaches and have caused a shift in channel adjustment processes towards bank failures and channel widening. Channel bank material accounts for at least 85 per cent of the material derived from the channel boundaries of the Yalobusha River system. Strategies to reduce downstream flooding problems while preventing upstream erosion and land loss are being contemplated by action agencies. One such proposal involves removal of the sediment/debris plug. Bank stability analyses that account for pore‐water and confining pressures have been conducted for a range of hydrologic conditions to aid in predicting future channel response. If the sediment/debris plug is removed to improve downstream drainage, care should be taken to provide sufficient time for drainage of groundwater from the channel banks so as not to induce accelerated bank failures. Published in 2002 John Wiley & Sons, Ltd.     

Bank erosion of legacy sediment at the transition from vertical to lateral stream incision

Streambank erosion is a primary source of suspended sediments in many waterways of the US Atlantic Piedmont. This problem is exacerbated where banks are comprised of fine sediment produced by the intensive land use practices of early European settlers. A stream in this region, Richland Creek incises into banks comprised of three stratigraphic layers associated with historic land use: pre‐European settlement, early European agriculture and development, and water‐powered milldam operation. This study aims to identify the bank processes along a reach of Richland Creek that is eroding towards its pre‐disturbance elevation. The volume of material that has eroded along this stream since the milldam breached was calculated by differencing a reconstructed surface of the pond bed and an aerial lidar digital terrain model (DTM). Immediately downstream from the study reach, the channel is floored by bedrock and immediately upstream the rate of channel erosion approximately doubled along the longitudinal profile of Richland Creek, which indicate that the study reach spans the transition from a channel dominated by vertical incision in the upstream direction to horizontal widening in the downstream direction. The combined hydrometeorological conditions and dominant processes causing reach‐scale cut bank erosion were investigated with analyses of stream stage, precipitation, and streambank volumetric and surfaces change that was measured during nine terrestrial lidar surveys in 2010–2012. The spatial variability of erosion during a simulated precipitation event was examined in a field‐based experiment. Erosion was greatest where mill pond sediment columns detached along vertical desiccation and horizontal seepage cracks. This sediment accumulated on the bank toe throughout the study and was a source of readily‐entrained fine sediment contrary to the upper reaches where depositional accommodation space is more limited. Findings suggest that hotspots of sediment excavation progress upstream, indicating that restoration efforts should focus upon stabilizing banks at these locations. Copyright © 2015 John Wiley & Sons, Ltd.     

Flood-duration-integrated stream power and frequency magnitude of >50-year-long sediment discharge out of a hyperarid watershed

Determining sediment discharge out of watersheds is a global, long-term challenge. In the vast, usually data-poor, hyperarid regions of the world, this is a greater challenge. Here, we present a unique, decades-long dataset of individual floods and their respective sediment discharge out of Nahal Yael, an experimental, well-instrumented, hyperarid (~25–30 mm year⁻¹) watershed in southern Israel. The high correlation between directly measured sediment yield by discrete individual floods and their respective total energy, represented by flood-integrated stream power (FISP), serves here as a rating curve. Using this rating curve, the 51-year-long series of FISP in Nahal Yael, calculated from the detailed individual flood hydrographs, was converted into a series of sediment yield by these floods. This, in turn, allows determining the long-term frequency-magnitude of sediment exported out of this hyperarid basin. This can assist in landscape evolution modeling, in testing impacts of flood frequency changes enforced by altered regional climatology, and hint at changes needed in forming the observed alluvial fans. We conclude that, at the decadal scale, moderate floods are the most effective in terms of total sediment transport. However, the recurrence intervals of these moderate hyperarid floods are longer than in temperate regions and reach 5–10 years.     

Controlling factors on the submarine canyon system: A case study of the Central Canyon System in the Qiongdongnan Basin,northern South China Sea

Based on an integrated analysis of high-resolution 2D/3D seismic data and drilling results, this study analyzes the tectonic-sedimentary evolution of the Qiongdongnan Basin (QDNB) since the late Miocene, and discusses the controlling factors on the formation and development of the Central Canyon System (CCS). The sediment failures caused by the relative sea level falling might have discharged deposits from the slope to the canyon. The two suits of the infillings, i.e., turbidites and mass transport complex (MTC), were derived from the northwestern source and northern source, respectively. The sediment supplies, which differ significantly among different areas, might have led to the variations observed in the internal architectures. Tectonic transformation around 11.6 Ma had provided the tectonic setting for the CCS and formed an axial sub-basin in the central part of the Changchang Depression, which could be called the rudiment of the CCS. The tectonic activity of the Red River Fault (RRF) at about 5.7 Ma might have strengthened the hydrodynamics of the deposits at the junction of the Yinggehai Basin (YGHB) and the QDNB to trigger a high-energy turbidity current. The MTC from the northern continental slope system might have been constrained by the Southern Uplift, functioning as a barrier for the infillings of the CCS. Thanks to a sufficient sediment supply during the Holocene period and the paleo-seafloor morphology, the relief of modern central canyon with the starving landform in the eastern Changchang Depression might have been accentuated by deposition of sediments and vertical growth along the canyon flanks, where collapse deposits were widely developed. Corresponding to the segmentation of the CCS, the forming mechanisms of the canyon between the three segments would be different. The turbidite channel in the head area had likely been triggered by the abundant sediment supply from the northwestern source together with the fault activity at about 5.7 Ma of the RRF. The formation and evolution of the canyon in the western segment were caused by combined effects of the turbidite channel from the northwestern source, the MTC from the northern continental slope, and the paleo-seafloor geomorphology. In the eastern segment, the canyon was constrained by the tectonic transformation occurring at approximately 11.6 Ma and the insufficient sediment supply from the wide-gentle slope.     

Channel stability and sediment source assessment in streams draining a Piedmont watershed in Georgia,USA

Streams can be classified as stable or unstable, depending on the stage of channel evolution. Many streams of the southern Piedmont in United States have high sediment loads and are listed as impaired under the total maximum daily load (TMDL) program and may be unstable. It is not clear as to what the target (reference) load or remediation measures should be for unstable streams. The objective of this study was to determine the relative channel stability for a typical southern Piedmont stream using rapid geomorphic assessments (RGAs) and sediment yield analysis. The results were supported through a sediment fingerprinting analysis. RGAs were performed along 52 reaches on the North Fork Broad River (NFBR) main stem and two tributaries. Annual sediment yields were calculated and compared with yields in the southern Piedmont for stable streams that are resilient to degradation or aggradation and unstable streams that are susceptible to such disturbances. Majority of the NFBR main stem was found to be unstable with signs of geomorphic instability in the form of degradation and aggradation. The estimated average annual sediment yield was 0·78 T ha^?1 year^?1. By comparison, the median annual yield is 0·20 T ha^?1 year^?1 for stable streams and 0·48 T ha^?1 year^?1 for unstable streams in the Piedmont ecoregion with comparable drainage basin size. We conclude that the NFBR is in an unstable stage of channel evolution. Sediment fingerprinting proved that majority of the stream‐suspended sediment emanated from eroding stream channels. The methods outlined in this study have implications for the reference condition and remediation efforts related to stream turbidity and stream channel restoration. Copyright © 2010 John Wiley & Sons, Ltd.     

三峡工程运用后荆江河段崩岸时空分布及其对河床调整的影响

三峡工程运用后长江中游荆江河段河床持续冲刷,局部河段崩岸频发,影响河道内悬沙输移与河床形态调整.本研究采用实测长程河道地形及固定断面地形资料,确定了2002-2018年荆江河段的主要崩岸区域,估算了崩岸土体的泥沙总量,进而定量分析了河岸崩退对河床调整的影响.计算结果表明:荆江段累计河岸崩退体积约为2.0亿m3,约占该河...     

LINKS BETWEEN PROGLACIAL STREAM SUSPENDED SEDIMENT DYNAMICS,GLACIER HYDROLOGY AND GLACIER MOTION AT MIDTDALSBREEN,NORWAY

Two-hourly suspended sediment concentration variations observed during the summer of 1987 in the proglacial stream draining Midtdalsbreen, Norway are modelled using multiple regression and time series techniques. Suspended sediment fluctuations are influenced by stream discharge variations, diurnal hysteresis effects, medium-term sediment supply and transport variations and the recent suspended sediment concentration history of the stream. They do not appear to be influenced by seasonal exhaustion or rainfall variations. Possible reasons for this are discussed. Large positive residuals from the fitted models are major pulses of suspended sediment unrelated to discharge variations; these sediment flushes correlate with periods of enhanced glacier motion. They cannot be explained by enhanced sediment production by subglacial erosion, but are probably due to the tapping of subglacially stored sediment during sudden changes in the hydraulics and/or configuration of the subglacial hydrological system. Seasonal changes in the lag between glacier motion peaks and suspended sediment flushes suggest that the subglacial hydrological system evolves over the summer from a distributed to a more channelized configuration.     

Predicting reach‐specific properties of fluvial terraces to guide future fieldwork. A case study for the Late Quaternary River Allier (France) with the FLUVER2 model

Numerical models have not yet systematically been used to predict properties of fluvial terrace records in order to guide fieldwork and sampling. This paper explores the potential of the longitudinal profile model FLUVER2 to predict testable field properties of the relatively well‐studied, Late Quaternary Allier system in France. For the Allier terraces an overlapping ¹⁴C and U‐series chronology as well as a record of ¹⁰Be erosion rates exist. The FLUVER2 modelling exercise is focused on the last 50 ka of the upper Allier reach because for this location and period the constraints of the available dating techniques are tightest. A systematic calibration based on terrace occurrence and thicknesses was done using three internal parameters related to (1) the sediment erodibility; (2) the sediment transport distance; and (3) the sediment supply derived from the surrounding landscape. As external model inputs, the best available, reconstructed, tectonic, climatic and base‐level data were used. Calibrated model outputs demonstrate a plausible match with the existing fluvial record. Validation of model output was done by comparing the modelled and measured timing of aggradation and incision phases for the three locations. The modelled range of landscape erosion rates showed a reasonably good match with existing erosion rate estimates derived from ¹⁰Be measurements of fluvial sands. The quasi‐validated model simulation was subsequently used to make new testable predictions about the timing and location of aggradation and erosion phases for three locations along the Allier river. The validated simulations predict that along the Allier, reach‐specific dynamics of incision and aggradation, related to the variations in sediment supply by major tributaries, cause relevant differences in the local fluvial terrace stratigraphy. Copyright © 2016 John Wiley & Sons, Ltd.     

The role of channel morphology on the mobility and dispersion of bed sediment in a small gravel‐bed stream

This study uses a unique 10‐year tracer dataset from a small gravel‐bed stream to examine bed mobility and sediment dispersion over long timescales and at a range of spatial scales. Seasonal tracer data that captured multiple mobilizing events was examined, while the effects of morphology on bed mobility and sediment dispersion were captured at three spatial scales: within morphological units (unit scale), between morphological units (reach scale) and between reaches with different channel morphologies (channel scale). This was achieved by analyzing both reach‐average mobility and travel distance data, as well as the development of ‘mobility maps’ that capture the spatial variability in tracer mobility within the channel. The tracer data suggest that sediment transport in East Creek remains near critical the majority of the time, with only rare large events resulting in high mobility rates and grain travel distances large enough to move sediment past dominant bedforms. While a variable capturing both the magnitude and frequency of flow events within a season yielded a better predictor to sediment mobility and dispersion than peak discharge alone, the distribution of events of different magnitude within the season played a large role in determining tracer mobility rates and travel distances. The effects of morphology differed depending on the analysis scale, demonstrating the importance of scale, and therefore study design, when examining the effect of morphology on sediment transport. Copyright © 2016 John Wiley & Sons, Ltd.     

Lithology‐controlled evolution of stream bed sediment and basin‐scale sediment yields in adjacent mountain watersheds,Idaho, USA

The composition, grain‐size, and flux of stream sediment evolve downstream in response to variations in basin‐scale sediment delivery, channel network structure, and diminution during transport. Here, we document downstream changes in lithology and grain size within two adjacent ~300 km² catchments in the northern Rocky Mountains, USA, which drain differing mixtures of soft and resistant rock types, and where measured sediment yields differ two‐fold. We use a simple erosion–abrasion mass balance model to predict the downstream evolution of sediment flux and composition using a Monte Carlo approach constrained by measured sediment flux. Results show that the downstream evolution of the bed sediment composition is predictably related to changes in underlying geology, influencing the proportion of sediment carried as bedload or suspended load. In the Big Wood basin, particle abrasion reduces the proportion of fine‐grained sedimentary and volcanic rocks, depressing bedload in favor of suspended load. Reduced bedload transport leads to stronger bed armoring, and coarse granitic rocks are concentrated in the stream bed. By contrast, in the North Fork Big Lost basin, bedload yields are three times higher, the stream bed is less armored, and bed sediment becomes dominated by durable quartzitic sandstones. For both basins, the geology‐based mass balance model can reproduce within ~5% root‐mean‐square error the composition of the bed substrate using realistic erosion and abrasion parameters. As bed sediment evolves downstream, bedload fluxes increase and decrease as a function of the abrasion parameter and the frequency and size of tributary junctions, while suspended load increases steadily. Variable erosion and abrasion rates produce conditions of variable bed‐material transport rates that are sensitive to the distribution of lithologies and channel network structure, and, provided sufficient diversity in bedrock geology, measurements of bed sediment composition allow for an assessment of sediment source areas and yield using a simple modeling approach. Copyright © 2016 John Wiley & Sons, Ltd.