Evidence of gas hydrate accumulation and its resource estimation in Andaman deep water basin from seismic and well log data

2D and 3D seismic reflection and well log data from Andaman deep water basin are analyzed to investigate geophysical evidence related to gas hydrate accumulation and saturation. Analysis of seismic data reveals the presence of a bottom simulating reflector (BSR) in the area showing all the characteristics of a classical BSR associated with gas hydrate accumulation. Double BSRs are also observed on some seismic sections of area (Area B) that suggest substantial changes in pressure–temperature (P–T) conditions in the past. The manifestation of changes in P–T conditions can also be marked by the varying gas hydrate stability zone thickness (200–650 m) in the area. The 3D seismic data of Area B located in the ponded fill, west of Alcock Rise has been pre-stack depth migrated. A significant velocity inversion across the BSR (1,950–1,650 m/s) has been observed on the velocity model obtained from pre-stack depth migration. The areas with low velocity of the order of 1,450 m/s below the BSR and high amplitudes indicate presence of dissociated or free gas beneath the hydrate layer. The amplitude variation with offset analysis of BSR depicts increase in amplitude with offset, a similar trend as observed for the BSR associated with the gas hydrate accumulations. The presence of gas hydrate shown by logging results from a drilled well for hydrocarbon exploration in Area B, where gas hydrate deposit was predicted from seismic evidence, validate our findings. The base of the hydrate layer derived from the resistivity and acoustic transit-time logs is in agreement with the depth of hydrate layer interpreted from the pre-stack depth migrated seismic section. The resistivity and acoustic transit-time logs indicate 30-m-thick hydrate layer at the depth interval of 1,865–1,895 m with 30 % hydrate saturation. The total hydrate bound gas in Area B is estimated to be 1.8 × 10¹⁰ m³, which is comparable (by volume) to the reserves in major conventional gas fields.     

Reservoir characterization of gas hydrate in the Northwestern part of the Ulleung Basin,East Sea

An analysis of 3D seismic data from the northwestern part of the Ulleung Basin, East Sea, revealed that the gas hydrate stability zone (GHSZ) consists of five seismic units separated by regional reflectors. An anticline is present that documents activity of many faults. The seismic indicators of gas hydrate occurrence included bottom simulating reflector (BSR) and acoustic blanking in the gas hydrate occurrence zone (GHOZ). By the analysis of the seismic characteristics and the gradient of the sedimentary strata, the GHOZ was divided into four classes: (1) dipping strata upon strong BSR, (2) dipping strata below strong BSR, (3) parallel strata with acoustic blanking, and (4) parallel strata below weak BSR. Seismic attributes such as reflection strength and instantaneous frequency were computed along the GHOZ. Low reflection strength and high instantaneous frequency were identified above the BSR, indicating the occurrence of gas hydrate. A remarkably high reflection strength and low instantaneous frequency indicated the presence of free gas below the BSR. Considering the distribution of the gas hydrate and free gas, two gas migration processes are suggested: (1) stratigraphic migration through the dipping, permeable strata and (2) structural migration from below the GHSZ along faults.     

Evidence for gas hydrate occurrences in the Canadian Arctic Beaufort Sea within permafrost-associated shelf and deep-water marine environments

The presence of a wedge of offshore permafrost on the shelf of the Canadian Beaufort Sea has been previously recognized and the consequence of a prolonged occurrence of such permafrost is the possibility of an underlying gas hydrate regime. We present the first evidence for wide-spread occurrences of gas hydrates across the shelf in water depths of 60–100 m using 3D and 2D multichannel seismic (MCS) data. A reflection with a polarity opposite to the seafloor was identified ∼1000 m below the seafloor that mimics some of the bottom-simulating reflections (BSRs) in marine gas hydrate regimes. However, the reflection is not truly bottom-simulating, as its depth is controlled by offshore permafrost. The depth of the reflection decreases with increasing water depth, as predicted from thermal modeling of the late Wisconsin transgression. The reflection crosscuts strata and defines a zone of enhanced reflectivity beneath it, which originates from free gas accumulated at the phase boundary over time as permafrost and associated gas hydrate stability zones thin in response to the transgression. The wide-spread gas hydrate occurrence beneath permafrost has implications on the region including drilling hazards associated with the presence of free gas, possible overpressure, lateral migration of fluids and expulsion at the seafloor. In contrast to the permafrost-associated gas hydrates, a deep-water marine BSR was also identified on MCS profiles. The MCS data show a polarity-reversed seismic reflection associated with a low-velocity zone beneath it. The seismic data coverage in the southern Beaufort Sea shows that the deep-water marine BSR is not uniformly present across the entire region. The regional discrepancy of the BSR occurrence between the US Alaska portion and the Mackenzie Delta region may be a result of high sedimentation rates expected for the central Mackenzie delta and high abundance of mass-transport deposits that prohibit gas to accumulate within and beneath the gas hydrate stability zone.     

Mapping gas hydrate and fluid flow indicators and modeling gas hydrate stability zone (GHSZ) in the Ulleung Basin,East (Japan) Sea: Potential linkage between the occurrence of mass failures and gas hydrate dissociation

The Ulleung Basin, East (Japan) Sea, is well-known for the occurrence of submarine slope failures along its entire margins and associated mass-transport deposits (MTDs). Previous studies postulated that gas hydrates which broadly exist in the basin could be related with the failure process. In this study, we identified various features of slope failures on the margins, such as landslide scars, slide/slump bodies, glide planes and MTDs, from a regional multi-channel seismic dataset. Seismic indicators of gas hydrates and associated gas/fluid flow, such as the bottom-simulating reflector (BSR), seismic chimneys, pockmarks, and reflection anomalies, were re-compiled. The gas hydrate occurrence zone (GHOZ) within the slope sediments was defined from the BSR distribution. The BSR is more pronounced along the southwestern slope. Its minimal depth is about 100 m below seafloor (mbsf) at about 300 m below sea-level (mbsl). Gas/fluid flow and seepage structures were present on the seismic data as columnar acoustic-blanking zones varying in width and height from tens to hundreds of meters. They were classified into: (a) buried seismic chimneys (BSC), (b) chimneys with a mound (SCM), and (c) chimneys with a depression/pockmark (SCD) on the seafloor. Reflection anomalies, i.e., enhanced reflections below the BSR and hyperbolic reflections which could indicate the presence of gas, together with pockmarks which are not associated with seismic chimneys, and SCDs are predominant in the western-southwestern margin, while the BSR, BSCs and SCMs are widely distributed in the southern and southwestern margins. Calculation of the present-day gas-hydrate stability zone (GHSZ) shows that the base of the GHSZ (BGHSZ) pinches out at water depths ranging between 180 and 260 mbsl. The occurrence of the uppermost landslide scars which is below about 190 mbsl is close to the range of the GHSZ pinch-out. The depths of the BSR are typically greater than the depths of the BGHSZ on the basin margins which may imply that the GHOZ is not stable. Close correlation between the spatial distribution of landslides, seismic features of free gas, gas/fluid flow and expulsion and the GHSZ may suggest that excess pore-pressure caused by gas hydrate dissociation could have had a role in slope failures.     

Variability of the bottom-simulating reflector (BSR) and its association with tectonic structures in the Chilean margin between Arauco Gulf (37°S) and Valdivia (40°S)

Multichannel seismic reflection data recorded between Arauco Gulf (37°S) and Valdivia (40°S), on the Chilean continental margin, were processed and modeled to obtain seismic images and sub-surface models, in order to characterize the variability of the bottom-simulating reflector (BSR), which is a geophysical marker for the presence of gas hydrates. The BSR is discontinuous and interrupted by submarine valleys, canyons, as well as by faults or fractures. The BSR occurrence is more common south of Mocha Island due to moderate slopes and greater organic matter contribution by rivers in that area. Tectonic uplift and structural instability change the stability gas hydrate zone and consequently the BSR position, creating in some cases missing or double BSRs. Our modeling supports the presence of gas hydrate above the BSR and free gas below it. Higher BSR amplitudes support higher hydrate or free gas concentrations. In the study area, gas hydrate concentration is low (an average of 3.5%) suggesting disseminated gas hydrate distribution within the sediments. Also higher BSR amplitudes are associated with thrust faults in the accretionary prism, which serve as conduits for gas flow from deeper levels. This extra gas supply produces a wider thickness of gas hydrates or free gas.     

A seismic study to investigate the prospect of gas hydrate in Mahanadi deep water basin,northeastern continental margin of India

The presence of gas hydrates, one of the new alternative energy resources for the future, along the Indian continental margins has been inferred mainly from bottom simulating reflectors (BSR) and the gas stability zone thickness mapping. Gas hydrate reserves in Krishna Godawari Basin have been established with the help of gas-hydrate related proxies inferred from multidisciplinary investigations. In the present study, an analysis of 3D seismic data of nearly 3,420 km² area of Mahanadi deep water basin was performed in search of seismic proxies related with the existence of natural gas hydrate in the region. Analysis depicts the presence of BSR-like features over a large areal extent of nearly 250 km² in the central western part of the basin, which exhibit all characteristics of a classical BSR associated with gas hydrate accumulation in a region. The observed BSR is present in a specific area restricted to a structural low at the Neogene level. The coherency inversion of pre-stack time migration (PSTM) gathers shows definite inversion of interval velocity across the BSR interface which indicates hydrate bearing sediments overlying the free gas bearing sediments. The amplitude versus offset analysis of PSTM gathers shows increase of amplitude with offset, a common trend as observed in BSR associated with gas hydrate accumulation. Results suggest the possibility of gas hydrate accumulation in the central part of the basin specifically in the area of structural low at the Neogene level. These results would serve as preliminary information for selecting prospective gas hydrate accumulation areas for further integrated or individual study from geophysical, geological, geochemical and microbiological perspectives for confirmation of gas hydrate reserves in the area. Further, on the basis of these results it is envisaged that biogenic gas might have been generated in the region which under suitable temperature and pressure conditions might have been transformed into the gas hydrates, and therefore, an integrated study comprising geophysical, geological, geochemical and microbiological data is suggested to establish the gas hydrate reserves in Mahanadi deep water basin.     

Seismic velocities on the Nova Scotian margin to estimate gas hydrate and free gas concentrations

This article provides new constraints on gas hydrate and free gas concentrations in the sediments at the margin off Nova Scotia. Two-dimensional (2-D) velocity models were constructed through simultaneous travel-time inversion of ocean-bottom seismometer (OBS) data and 2-D single-channel seismic (SCS) data acquired in two surveys, in 2004 and 2006. The surveys, separated by ∼5 km, were carried out in regions where the bottom-simulating reflection (BSR) was identified in seismic reflection datasets from earlier studies and address the question of whether the BSR is a good indicator of significant gas hydrate on the Scotian margin. For both datasets, velocity increases by 200–300 m/s at a depth of approximately 220 m below seafloor (mbsf), but the results of the 2006 survey show a smaller velocity decrease (50–80 m/s) at the base of this high-velocity layer (310–330 mbsf) than the results of the 2004 survey (130 m/s). When converted to gas hydrate concentrations using effective medium theory, the 2-D velocity models for both datasets show a gas hydrate layer of ∼100 m thickness above the identified BSR. Gas hydrate concentrations are estimated at approximately 2–10% for the 2006 data and 8–18% for the 2004 survey. The reduction in gas hydrate concentration relative to the distance from the Mohican Channel structure is most likely related to the low porosity within the mud-dominant sediment at the depth of the BSR. Free gas concentrations were calculated to be 1–2% of the sediment pore space for both datasets.     

Seismic imaging of a fractured gas hydrate system in the Krishna–Godavari Basin offshore India

Gas hydrate was discovered in the Krishna–Godavari (KG) Basin during the India National Gas Hydrate Program (NGHP) Expedition 1 at Site NGHP-01-10 within a fractured clay-dominated sedimentary system. Logging-while-drilling (LWD), coring, and wire-line logging confirmed gas hydrate dominantly in fractures at four borehole sites spanning a 500 m transect. Three-dimensional (3D) seismic data were subsequently used to image the fractured system and explain the occurrence of gas hydrate associated with the fractures. A system of two fault-sets was identified, part of a typical passive margin tectonic setting. The LWD-derived fracture network at Hole NGHP-01-10A is to some extent seen in the seismic data and was mapped using seismic coherency attributes. The fractured system around Site NGHP-01-10 extends over a triangular-shaped area of ∼2.5 km² defined using seismic attributes of the seafloor reflection, as well as “seismic sweetness” at the base of the gas hydrate occurrence zone. The triangular shaped area is also showing a polygonal (nearly hexagonal) fault pattern, distinct from other more rectangular fault patterns observed in the study area. The occurrence of gas hydrate at Site NGHP-01-10 is the result of a specific combination of tectonic fault orientations and the abundance of free gas migration from a deeper gas source. The triangular-shaped area of enriched gas hydrate occurrence is bound by two faults acting as migration conduits. Additionally, the fault-associated sediment deformation provides a possible migration pathway for the free gas from the deeper gas source into the gas hydrate stability zone. It is proposed that there are additional locations in the KG Basin with possible gas hydrate accumulation of similar tectonic conditions, and one such location was identified from the 3D seismic data ˜6 km NW of Site NGHP-01-10.     

A margin-wide BSR gas hydrate assessment: Canada’s Atlantic margin

It is the intent of this paper to explore a significant extent of an entire passive continental margin for hydrate occurrence to understand hydrate modes of occurrence, preferred geologic settings and estimate potential volumes of methane. The presence of gas hydrates offshore of eastern Canada has long been inferred from estimated stability zone calculations, but little physical evidence has been offered. An extensive set of 2-D and 3-D, single and multi-channel seismic reflection data comprising in excess of 140,000 line-km was analyzed. Bottom simulating reflections (BSR) were unequivocally identified at seven sites, ranging between 250 and 445 m below the seafloor and in water depths of 620-2850 m. The combined area of the BSRs is 9311 km², which comprises a small proportion of the entire theoretical stability zone along the Canadian Atlantic margin (∼715,165 km²). The BSR within at least six of these sites lies in a sedimentary drift deposit or sediment wave field, indicating the likelihood of grain sorting and potential porosity and permeability (reservoir) development. Although there are a variety of conditions required to generate and recognize a BSR, one might assume that these sites offer the most potential for highest hydrate concentration and exploitation. Total hydrate in formation at the sites of recognized BSR’s is estimated at 17 to 190 × 10⁹ m³ or 0.28 to 3.12 × 10¹³ m³ of methane gas at STP. Although it has been shown that hydrate can exist without a BSR, the results from this regional study argue that conservative estimates of the global reserve of hydrate along continental margins are necessary.     

The enigma of double BSRs: indicators for changes in the hydrate stability field?

 A classical bottom simulating reflector (BSR) and a presently unknown double BSR pattern are detectable in reflection seismic profiles from the Storegga Slide area west of Norway. Pressure and temperature modeling schemes lead to the assumption that the strong BSR marks the base of a hydrate stability zone with a typical methane gas composition of 99%. The upper double BSR may mark the top of gas hydrates and the lower double BSR may represent a relict of former changes of the hydrate stability field from glacial to interglacial times or the base of gas hydrates with a gas composition including heavier hydrocarbons.     

Multi-frequency seismic study of gas hydrate-bearing sediments in Lake Baikal,Siberia

In this paper we present and discuss the frequency-dependent behaviour of the acoustic characteristics of methane hydrate-bearing sediments in Lake Baikal, Siberia. Five different types of seismic sources (airgun-array, two types of single airguns, watergun and sparker) are used, encompassing a frequency bandwidth from 10 up to 1000 Hz. On low-frequency airgun-array data, the base of the hydrate stability zone (HSZ) is observed as a high-amplitude bottom-simulating reflection (BSR) with reversed polarity. The amplitude and continuity of the BSR decrease or even disappear on medium- to high-frequency data, a feature explained in terms of vertical and horizontal resolution. The increasing reflection amplitude of the BSR with increasing offset, the calculated reflection coefficient of the BSR and the occurrence of enhanced reflections below the BSR suggest the presence of free gas below the HSZ. The observation of some enhanced reflections extending above the BSR may be interpreted as an indication for free gas co-existing with hydrates within the HSZ. Amplitude blanking above the BSR is highly variable while the BSR itself appears to act as a low-pass frequency filter for medium- to high-frequency data.New single-channel airgun profiles provide the first seismic information across the Baikal Drilling Project (BDP-97) deep drilling site, at which hydrate-bearing sediments were retrieved at about 200 m above the base of the local HSZ. At the drilling site there are no seismic characteristics indicative of the presence of hydrates. Combination of the drilling and seismic information has allowed us to make a rough estimation of the volume of hydrates and carbon stored in the sediments of Lake Baikal, which lead us to conclude that the Lake Baikal gas hydrate reservoirs do not form a prospective energy resource.     

Geothermal modeling of the gas hydrate stability zone along the Krishna Godavari Basin

A wide-spread bottom simulating reflector (BSR), interpreted to mark the thermally controlled base of the gas hydrate stability zone, is observed over a close grid of multichannel seismic profiles in the Krishna Godavari Basin of the eastern continental margin of India. The seismic data reveal that gas hydrate occurs in the Krishna Godavari Basin at places where water depths exceed 850 m. The thickness of the gas hydrate stability zone inferred from the BSR ranges up to 250 m. A conductive model was used to determine geothermal gradients and heat flow. Ground truth for the assessment and constraints on the model were provided by downhole measurements obtained during the National Gas Hydrate Program Expedition 01 of India at various sites in the Krishna Godavari Basin. Measured downhole temperature gradients and seafloor-temperatures, sediment thermal conductivities, and seismic velocity are utilized to generate regression functions for these parameters as function of overall water depth. In the first approach the base of gas hydrate stability is predicted from seafloor bathymetry using these regression functions and heat flow and geothermal gradient are calculated. In a second approach the observed BSR depth from the seismic profiles (measured in two-way travel time) is converted into heat flow and geothermal gradient using the same ground-truth data. The geothermal gradient estimated from the BSR varies from 27 to 67°C/km. Corresponding heat flow values range from 24 to 60 mW/m². The geothermal modeling shows a close match of the predicted base of the gas hydrate stability zone with the observed BSR depths.     

AVO analysis of BSR to assess free gas within fine-grained sediments in the Shenhu area,South China Sea

Gas hydrates have been identified from two-dimensional (2D) seismic data and logging data above bottom simulating reflector (BSR) during China’s first gas hydrate drilling expedition in 2007. The multichannel reflection seismic data were processed to be preserved amplitudes for quantitatively analyzing amplitude variation with offset (AVO) at BSRs. Low P-wave velocity anomaly below BSR, coinciding with high amplitude reflections in 2D seismic data, indicates the presence of free gas. The absolute values of reflection coefficient versus incidence angles for BSR range from 0 to 0.12 at different CMPs near Site SH2. According to logging data and gas hydrate saturations estimated from resistivity of Site SH2, P-wave velocities calculated from effective media theory (EMT) fit the measured sonic velocities well and we choose EMT to calculate elastic velocities for AVO. The rock-physics modeling and AVO analysis were combined to quantitatively assess free gas saturations and distribution by the reflection coefficients variation of the BSRs in Shenhu area, South China Sea. AVO estimation indicates that free gas saturations immediately beneath BSRs may be about 0.2 % (uniform distribution) and up to about 10 % (patchy distribution) at Site SH2.     

Gas hydrate saturation in the Krishna–Godavari basin from P-wave velocity and electrical resistivity logs

During the Indian National Gas Hydrate Program (NGHP) Expedition 01, a series of well logs were acquired at several sites across the Krishna–Godavari (KG) Basin. Electrical resistivity logs were used for gas hydrate saturation estimates using Archie’s method. The measured in situ pore-water salinity, seafloor temperature and geothermal gradients were used to determine the baseline pore-water resistivity. In the absence of core data, Arp’s law was used to estimate in situ pore-water resistivity. Uncertainties in the Archie’s approach are related to the calibration of Archie coefficient (a), cementation factor (m) and saturation exponent (n) values. We also have estimated gas hydrate saturation from sonic P-wave velocity logs considering the gas hydrate in-frame effective medium rock-physics model. Uncertainties in the effective medium modeling stem from the choice of mineral assemblage used in the model. In both methods we assume that gas hydrate forms in sediment pore space. Combined observations from these analyses show that gas hydrate saturations are relatively low (<5% of the pore space) at the sites of the KG Basin. However, several intervals of increased saturations were observed e.g. at Site NGHP-01-03 (S_h = 15–20%, in two zones between 168 and 198 mbsf), Site NGHP-01-05 (S_h = 35–38% in two discrete zone between 70 and 90 mbsf), and Site NGHP-01-07 shows the gas hydrate saturation more than 25% in two zones between 75 and 155 mbsf. A total of 10 drill sites and associated log data, regional occurrences of bottom-simulating reflectors from 2D and 3D seismic data, and thermal modeling of the gas hydrate stability zone, were used to estimate the total amount of gas hydrate within the KG Basin. Average gas hydrate saturations for the entire gas hydrate stability zone (seafloor to base of gas hydrate stability), sediment porosities, and statistically derived extreme values for these parameters were defined from the logs. The total area considered based on the BSR seismic data covers ∼720 km². Using the statistical ranges in all parameters involved in the calculation, the total amount of gas from gas hydrate in the KG Basin study area varies from a minimum of ∼5.7 trillion-cubic feet (TCF) to ∼32.1 TCF.     

High-resolution P-Cable 3D seismic imaging of gas chimney structures in gas hydrated sediments of an Arctic sediment drift

The newly developed P-Cable 3D seismic system allows for high-resolution seismic imaging to characterize upper geosphere geological features focusing on geofluid expressions (gas chimneys), shallow gas and gas hydrate reservoirs. Seismic imaging of a geofluid system of an Arctic sediment drift at the Vestnesa Ridge, offshore western Svalbard, provides significantly improved details of internal chimney structures from the seafloor to ∼500 m bsf (below seafloor). The chimneys connect to pockmarks at the seafloor and indicate focused fluid flow through gas hydrated sediments. The pockmarks are not buried and align at the ridge-crest pointing to recent, topography-controlled fluid discharge. Chimneys are fuelled by sources beneath the base of gas hydrate stability zone (GHSZ) that is evident at ∼160–170 m bsf as indicated by a bottom-simulating reflector (BSR). Conduit centres that are not vertically straight but shift laterally by up to 200 m as well as discontinuous internal chimney reflections indicate heterogeneous hydraulic fracturing of the sediments. Episodically active, pressure-driven focused fluid flow could explain the hydro-fracturing processes that control the plumbing system and lead to extensive pockmark formation at crest of the Vestnesa Ridge. High-amplitude anomalies in the upper 50 m of the chimney structures suggest formations of near-surface gas hydrates and/or authigenic carbonate precipitation. Acoustic anomalies, expressed as high amplitudes and amplitude blanking, are irregularly distributed throughout the deeper parts of the chimneys and provide evidence for the variability of hydrate and/or carbonate formation in space and time.     

High-resolution seismic studies of gas hydrates west of Svalbard

 A strong bottom-simulating reflection (BSR) with high-amplitude variations is detectable in high- resolution reflection seismic profiles west of Svalbard. Above the BSR, anomalously high velocities up to 1840 m/s, calculated from high-frequency ocean-bottom hydrophone (HF-OBH) data, indicate the existence of gas-hydrated sediments. Below the BSR, a low-velocity layer, interpreted as gas-bearing sediments, shows thickness variations from 12 to 25 m. In addition, two other low-velocity layers clearly containing free gas are detected within the classic hydrate stability zone (HSZ) where, a theoretical viewpoint, free gas cannot exist. Received: 6 August 1997 / Revision received: 26 January 1998     

冲绳海槽天然气水合物稳定带特征和资源量评价

根据冲绳海槽多道地震资料的处理解释,在16条地震剖面上发现了水合物拟海底反射层BSR,经过AVO、波形反演等特殊的处理技术,首次直接利用BSR圈定了冲绳海槽天然气水合物具体分布范围,直接利用数据得出了天然气水合物稳定带厚度在冲绳海槽的分布趋势,认为海槽南部最厚,中部次之,北部最薄,并通过计算得出了冲绳海槽水合物稳定带的厚度和水合物资源量,对今后海槽水合物勘查和资源量评价具有一定的指导意义。     

冲绳海槽天然气水合物稳定带特征及资源量评价

根据冲绳海槽多道地震资料的处理解释,在16条地震剖面上发现了水合物似海底反射层BSR,经过AVO、波形反演等特殊的处理技术,首次直接利用BSR圈定了冲绳海槽天然气水合物的具体分布范围,直接利用数据得出了天然气水合物稳定带厚度在冲绳海槽的分布趋势,认为海槽南部最厚,中部次之,北部最薄,并通过计算得出了冲绳海槽水合物稳定带的厚度和水合物资源量,对今后海槽水合物勘查和资源量评价具有一定的指导意义.     

Gas hydrates in the western deep-water Ulleung Basin, East Sea of Korea

Geophysical surveys and geological studies of gas hydrates in the western deep-water Ulleung Basin of the East Sea off the east coast of Korea have been carried out by the Korea Institute of Geoscience and Mineral Resources (KIGAM) since 2000. The work included a grid of 4782 km of 2D multi-channel seismic reflection lines and 11 piston cores 5–8 m long. In the piston cores, cracks generally parallel to bedding suggest significant in-situ gas. The cores showed high amounts of total organic carbon (TOC), and from the southern study area showed high residual hydrocarbon gas concentrations. The lack of higher hydrocarbons and the carbon isotope ratios indicate that the methane is primarily biogenic. The seismic data show areas of bottom-simulating reflectors (BSRs) that are associated with gas hydrates and underlying free gas. An important observation is the numerous seismic blanking zones up to 2 km across that probably reflect widespread fluid and gas venting and that are inferred to contain substantial gas hydrate. Some of the important results are: (1) BSRs are widespread, although most have low amplitudes; (2) increased P-wave velocities above some BSRs suggest distributed low to moderate concentration gas hydrate whereas a velocity decrease below the BSR suggests free gas; (3) the blanking zones are often associated with upbowing of sedimentary bedding reflectors in time sections that has been interpreted at least in part due to velocity pull-up produced by high-velocity gas hydrate. High gas hydrate concentrations are also inferred in several examples where high interval velocities are resolved within the blanking zones. Recently, gas hydrate recoveries by the piston coring and deep-drilling in 2007 support the interpretation of substantial gas hydrate in many of these structures.