基于空间插值的工程岩体RQD预测方法

作为工程实际中评价岩体性质的重要指标,RQD的应用已相当广泛。但工程岩体中RQD值的分布存在一定的结构性和随机性,因此,通过对特定位置钻探获取的RQD值无法很到位地表达整个空间区域的实际岩石质量。为了弥补这方面的不足,统计学中的空间插值法为此提供了有力的手段。考虑到空间RQD分布存在各向异性,以及在工程坐标系中很难描述RQD分布的结构性,首先计算工程坐标系下已获取RQD值的主要黑塞方向（pHd）;然后构建空间旋转与比例缩放矩阵对其进行坐标标准化处理。在标准化的空间中,引入Kriging插值法,采用变异函数描述RQD在标准空间结构上的变化,建立其空间变异规律的数学模型,并对其进行插值计算;最后将标准空间进行坐标逆变换,实现了对工程坐标系下RQD分布的预测。利用R语言编程将该方法应用于工程实例,结果表明,这种空间插值法能够有效地预测工程岩体中RQD值的分布规律,弥补了局部钻探的局限性。     

广义RQD在岩体各向异性中的应用研究

RQD作为工程实际中评价岩体性质的方法，应用已相当广泛，并已列入有关规范，然而，由于传统Deere定义的RQD在实际应用中存在很多问题，所以引入了不同阈值的广义RQD的概念，并结合不连续面三维网络模拟技术判定岩体的各向异性程序。在对长白公路石碑岭隧道围岩的生中，说明了广义RQD用于判定岩体各向异性的有效性和可行性。     

Rock quality designation-fracture intensity index method for geomechanical classification

Rock quality designation (RQD) is a simple and effective way of rock mass classification from surface scanlines or preferably borehole measurements. A major drawback in its classical use is that only one representative RQD value is obtained from the field measurements per core run. However, it is shown in this paper that the field measurements along a scanline provide detailed information about the rock quality and the fracture intensity (FI) for a given number of joints. In order to be able to extract the complete information concealed within the field data, the RQD-fracture index diagram concept is proposed and applied to actual field scanline measurements from England. The basis of the suggested procedure is to obtain a series of all possible RQD and FI values from given intact length measurements. This procedure provides additional information as to the local zones of heterogeneities within the rock mass and a new way of rock classification on the basis of the combined effects of RQD and FI. It is also possible to calculate percentages of different rock qualities within the same rock mass.     

结构面三维网络模拟在岩体质量评价中的应用

岩石质量指标RQD是反映工程岩体完整程度的定量参数,广泛用于水利水电、矿山、地下工程、交通工程等岩体稳定性评价,但是传统的RQD定义不能满足实际工程岩体各相异性要求。针对贵州黔中水利枢纽工程拱坝坝基岩体结构面特征,利用Monte-Carlo法在计算机上生成岩体节理三维网络图,建立了模拟计算不同阀值t的岩石质量指标RQDt的计算机模拟方法。该方法能较真实客观地描述岩石质量。     

RQD应用与研究的回顾与展望

RQD是评价裂隙岩体质量的重要参数,它在岩体工程中被广泛采用,但经过长期的理论和实践工程师们认识到了RQD自身所存在的缺点和不足,并将RQD的缺点和不足总结为5点。但RQD仍然具有很强的生命力,从5个方面总结了近半个世纪以来人们对RQD的不断探索和研究的进程,并进一步指出了对RQD的拓宽和改进的主要研究方法和发展方向。     

三维网络结构岩体力学架构与展望

三维网络结构岩体力学是岩体力学的一个分支。根据笔者20余年对裂隙岩体研究的心得,阐述了三维网络结构岩体力学的主要特点、研究对象,基本架构、主要研究内容与未来的展望。将岩体结构控制论归结为材料强度控制、结构类型控制、渗流通道控制和几何边界控制4个方面。技术层面的主要内容包括三维RQD估算、岩体表征单元估算技术、结构块体搜索技术、定向投影岩体结构面三维连通率估算技术以及岩体三维渗径搜索技术等。理论层面主要由球面投影理论、概率统计理论、随机动力学、几何拓扑理论、块体理论、非线性系统理论和裂隙岩体多尺度等效结构模型等构成。强调足量的随机不连续面地质信息的原位统计取样是三维网络结构岩体力学的基础,岩体随机不连续面三维网络数值模拟技术是三维网络结构岩体力学的核心技术。     

利用RQD估算岩体不同深度的平均渗透系数和平均变形模量

渗透系数是进行裂隙岩体渗流模拟的必备参数,变形模量是工程岩体数值模拟的必备参数。大量研究中忽视了渗透系数和变形模量随深度变化这一重要规律,从而影响模拟结果的可靠性。为此,探讨了利用极易获取的RQD（岩石质量指标）资料估算不同深度的渗透系数和变形模量的可行性。通过以某花岗岩体为例,研究发现,RQD均值随深度增大,渗透系数均值随深度减小,其相关性很好。因此,利用RQD估算不同深度的平均渗透系数是可行的。根据RQD随深度的变化,利用经验公式估算了不同深度的变形模量均值和变化范围。估算得到的变形模量与实测结果基本一致。     

利用岩石质量指标和岩体块度指数进行岩体质量评价研究——以高放废物地质处置库预选场址甘肃北山1号钻孔为例

岩体质量的评价对于各类大型建筑物特别是地下工程建筑物的安全性具有十分重要的作用。文章基于岩石质量指标（RQD）和岩体块度指数（RBI）的理论，通过对甘肃北山1号钻孔的岩心实测资料证明，岩体块度指数在一定程度上能反映岩体的完整性与相应力学性质的变化特点，同时给出钻孔附近岩体质量分类，进而与岩石质量指标所获得的钻孔附近岩体质量评价分级进行对比。对比结果表明：岩体块度指数在岩石质量评价中能更准确地反映其优越性，具有更为显著的工程意义。     

岩体完整性指标IRMI的工程应用与分析

岩体完整性指标（IRMI）是基于钻孔成像技术的评价岩体完整性的新指标,定义为全孔孔壁图像中岩体完整特征I与孔壁岩体长度（即完整特征I与破碎特征F之和）之比的百分数,即IRMI = I / (I + F)。钻孔成像技术在青岛海湾大桥基础勘察工程中取得了成功应用,获得了大量的第一手资料。通过与钻探和其他岩石质量估算法的对比分析,得出(1) 钻孔摄像弥补了钻孔取芯的不足;(2) 全孔图像为实现准确的岩体完整性评价创造了条件;(3) IRMI能准确地反映岩体完整特征;(4）IRMI通常大于RQD。     

基于BQ系统的阿拉善巴彦诺日公NRG01号钻孔岩体质量评价

高放废物深部地质处置目前受到世界各国的高度重视,处置库围岩岩体质量评价是高放废物处置库选址的关键问题之一。文章基于BQ系统对我国高放废物地质处置库阿拉善预选区巴彦诺日公NRG01号钻孔进行了岩体质量评价。NRG01号孔钻孔资料丰富,采用岩芯编录、波速测井、水压致裂地应力测量及岩石波速测试、单轴压缩试验等多种方法手段相结合的方式获取了BQ评价系统中的各个参数。评价过程中,综合考虑了岩体坚硬程度、完整程度及地下水、软弱结构面、初始地应力等因素对围岩稳定的影响。根据计算的[BQ]值对岩体质量进行评价并与RQD评价结果进行对比。评价结果表明,NRG01号孔岩体质量较好,Ⅰ级和Ⅱ级岩体占90%,410~500 m的岩体范围可作为处置库建设的目标岩体。[BQ]值与RQD值所得的岩体质量评价结果一致性良好,但由于BQ系统考虑的影响因素更为全面,评价结果更为精细。本次评价可为巴彦诺日公地段高放废物地质处置库场址比选及处置库目标岩体选择提供依据。     

Fault detection in 3D by sequential Gaussian simulation of Rock Quality Designation (RQD)

Gazestan phosphate ore deposit (Central Iran) is an apatite deposit which is instrumental in selecting the method of excavation. The position of fault systems and the condition of rock quality also play a role in the method used for mineral resources and ore reserves estimation. Conversely, the Rock Quality Designation (RQD) is a parameter that provides a quantitative judgment of rock mass quality obtained from drill cores. This factor can be applied to detect the fractured zones which occur due to fault systems. Additionally, the faulted areas can be determined by surface geological map and a few by core drilling. Some of the faulted areas are not distinguishable in the surface and are covered by soils, especially within 3D modeling and visualization. In this study, an attempt has been made to establish a relationship between the RQD percentages which were geostatistically simulated and faulted areas through the region. In comparison, the results showed that low RQD domains (RQD <20 %) can be interpreted as fault zones; high RQD domains (RQD >50 %) correspond to less fractured areas, and the contact between high and low RQD domain is gradual. Therefore, this categorization of RQD domains can be incorporated to detect the faulted zones in 3D models for mine design. Based on the categorization, the uncertainty within the area was calculated to introduce two new core drilling points for the completion of this phase of exploratory grid from the fault structural viewpoint, in order to have a proper model of ore reserve to estimate. It was concluded that this procedure can be utilized for conceptual comprehension of fault trends in 3D modeling for the method selection of excavation and complete the estimation procedure phase.     

A coupled hydromechanical system defined through rock mass classification schemes

Changes in the hydraulic conductivity field, resulting from the redistribution of stresses in fractured rock masses, are difficult to characterize due to complex nature of the coupled hydromechanical processes. A methodology is developed to predict the distributed hydraulic conductivity field based on the original undisturbed parameters of hydraulic conductivity, Rock Mass Rating (RMR), Rock Quality Designation (RQD), and additionally the induced strains. The most obvious advantage of the methodology is that these required parameters are minimal and are readily available in practice. The incorporation of RMR and RQD, both of which have been applied to design in rock engineering for decades, enables the stress-dependent hydraulic conductivity field to be represented for a whole spectrum of rock masses. Knowledge of the RQD, together with the original hydraulic conductivity, is applied to determine the effective porosity for the fractured media. When RQD approaches zero, the rock mass is highly fractured, and fracture permeability will be relatively high. When RQD approaches 100, the degree of fracturing is minimal, and secondary porosity and secondary permeability will be low. These values bound the possible ranges in hydraulic behaviour of the secondary porosity within the system. RMR may also be applied to determine the scale effect of elastic modulus. As RMR approaches 100, the ‘softening’ effect of fractures is a minimum and results in the smallest strain-induced change in the hydraulic conductivity because the induced strain is uniformly distributed between fractures and matrix. When RMR approaches zero, the laboratory modulus must be reduced significantly in order to represent the rock mass. This results in the largest possible change in the hydraulic conductivity because the induced strain is applied entirely to the fracture system. These values of RMR bound the possible ranges in mechanical behaviour of the system. The mechanical system is coupled with the hydraulic system by two empirical parameters, RQD and RMR. The methodology has been applied to a circular underground excavation and to qualitatively explain the in situ experimental results of the macropermeability test in the drift at Stripa. Copyright © 1999 John Wiley & Sons, Ltd.     

基于结构面网络模拟的岩体深部卸荷裂隙及非均质特性研究

深部卸荷裂隙是一类非构造成因的特殊地质现象,常出现在高山峡谷地带,对工程建设有重要影响。将二维结构面网络模拟运用于模拟某水电站边坡平硐内深部卸荷裂隙和常规卸荷裂隙,在该模拟结果中布设18个虚拟钻孔,利用Autolisp编写岩石质量指标统计程序来计算岩体RQD值。并统计、对比两类裂隙岩体在不同阈值的岩体RQD值及其标准差。利用RQD值的差异将两类岩体裂隙实现区分,同时基于RQD值的标准差体现出的数据的离散性,进一步分析裂隙岩体的非均质特性。     

某大型水电站坝区岩体风化分带定量划分初探

岩体风化程度的划分对岩体质量的准确分级及建基面的确定具有重要意义。但定性划分岩体风化程度往往受到主观因素的制约,存在评价时的任意性,且不能客观反映岩体风化的本质特征。而选取一些能反映岩体风化特征的指标对岩体进行风化量化分级,则较为准确、客观。论文结合西南某大型电站基本情况,根据国内外的研究成果,选取岩石质量指标（RQD）、裂隙间距（D）、波速比（Bv）、完整性系数（Kv）、岩石单轴抗压强度及2m硐段裂隙数等适合坝区岩体定量风化分带的特征指标,对主要指标进行相关性分析。最后根据选定指标定量划分出坝区岩体风化分带,以期对类似工程有一定的指导意义。     

Strain-dependent Fluid Flow Defined Through Rock Mass Classification Schemes

Summary ?Strain-dependent hydraulic conductivities are uniquely defined by an environmental factor, representing applied normal and shear strains, combined with intrinsic material parameters representing mass and component deformation moduli, initial conductivities, and mass structure. The components representing mass moduli and structure are defined in terms of RQD (rock quality designation) and RMR (rock mass rating) to represent the response of a whole spectrum of rock masses, varying from highly fractured (crushed) rock to intact rock. These two empirical parameters determine the hydraulic response of a fractured medium to the induced-deformations. The constitutive relations are verified against available published data and applied to study one-dimensional, strain-dependent fluid flow. Analytical results indicate that both normal and shear strains exert a significant influence on the processes of fluid flow and that the magnitude of this influence is regulated by the values of RQD and RMR.     

花岗岩体钻孔中结构面的分布规律——以深圳大亚湾花岗岩体为例

结构面对工程岩体的强度及其稳定性起着关键作用。在工程选址时常会首先考虑花岗岩作为其地基或围岩,而钻孔揭露的是目标深度岩体最直接的数据。以广东深圳的大亚湾花岗岩体为例,结合地质背景,研究钻孔方向上结构面的分布规律。钻孔方向上花岗岩结构面主要为构造结构面和表生结构面。首先,对比沿钻孔方向花岗岩体中结构面与地表结构面的倾向与倾角,在同一场址区,受到同一构造作用影响,钻孔中与地表节理的产状分布类似。其次,研究沿钻孔方向结构面的间距（直接影响岩体的RQD值）,通过间距分组和回归分析,发现结构面间距与其频数具有明显的幂函数关系,且该关系式与RQD值相关。     

煤矿床工程地质勘查中岩石质量指标(RQD)存在问题的探讨

岩石质量指标(RQD)是评价岩体完整性及质量分级的一个重要指标。针对矿区工程地质勘查规范中推荐的岩体质量评价方法,详细分析了岩石质量指标(RQD)在用于岩体分类与评价中存在的岩心长度的计算、采取率、硬度和结构对其赋值大小的影响,以及对规范理解的差异,提出了解决这些问题的有效方法与途径,为岩石质量指标(RQD)的正确应用及煤矿床岩体质量合理评价做了有益的探讨。     

基于三维结构面网络模拟的岩体变形模量确定方法

变形模量作为表征岩体变形特征的重要参数,是岩体工程设计的基础力学参数之一。在综合前人研究的基础上提出了基于三维结构面网络模拟确定岩体变形模量的方法,编制了三维结构面网络模拟及计算RQD值的程序。以西南山区某水电站坝址区岩体为实例,在概率统计各组优势结构面几何要素分布形式的基础上,采用Monte Carlo法生成三维结构面网络模型,据此获得岩体三维RQD值,利用RMR法进行质量评价和变形模量的确定,并与钻孔资料统计法和原位试验结果进行对比分析。结果表明:基于钻孔资料统计的估算结果与原位试验相对误差达31.62%,且其估算值偏低;基于三维结构面网络模拟的估算结果与原位试验相对误差仅为2.56%,估算结果精度较高。该方法考虑了岩体质量的空间各向异性,对岩体的质量评价和参数确定更为合理,研究成果为该工程的优化设计提供了合理的计算参数。      

裂隙岩体流固耦合双重介质模型的有限元计算

基于孔隙-裂隙岩体的双重孔隙介质流固耦合计算的微分方程,利用伽辽金有限元法提出的相应有限元公式,并基于岩体分类指标（RQD,RMR）提出了与岩体应力状态相关的渗透系数计算公式。编制了相应的有限元程序并给出了应用算例,将计算结果与相关文献作了比较,得出相关结论。     

铁路岩质边坡的RQD研究

以宝成铁路略阳站前后一段铁路工程边坡为例,采用蒙特卡洛原理和方法,计算模拟铁路边结构面概率参数,利用统计结果估算边坡岩体的岩石质量指标ＲＱＤ,提出方向ＲＱＤ的概念,初探方向ＲＱＤ值在铁路工程边坡中的应用及铁路开挖工程活动与自然地质环境间的相互影响。