高频波浪的测量与谱分析

为了解高频海浪的特征,通过在实验室风浪水槽中进行实验测量,获取了风浪高频部分的数据.实验采用直径为 0.2 mm 的细钽丝作传感器,采样间隔为 0.005 s,每组采集 30 000 个数据,以获得对波浪高频部分的更多的信息.通过分析,得到了高频风浪谱参数及其平衡域的特性,并提出次峰现象可能是采样速率过低、因计算方法造成的假象,并不是海浪特有的高频现象.     

基于阻抗匹配条件的树枝状超材料吸收器

基于树枝状金属结构单元的电磁谐振特性,设计了一种双面大小树枝状结构的超材料吸收器,该结构分别是正面二级树枝及正对的背面三级树枝.通过仿真模拟设计了不同的阻抗匹配方式,调节相应的结构参数,找到了阻抗匹配对吸收特性的影响.在最佳的阻抗匹配条件下,得到最大吸收率.实验测量表明,阻抗匹配条件下双面大小树枝模型可以实现90.01%吸收率.增加样品层数可以有效的增加吸收率,3层样品就可以达到99%以上的吸收率,实现工程意义的完美吸收.     

海洋绞车主动升沉补偿控制系统建模与仿真分析

针对海洋绞车主动升沉补偿系统的控制要求,通过对主动升沉补偿系统的控制机理进行分析,于Simulink软件中搭建海洋绞车主动升沉补偿控制系统的仿真模型。根据负载所处不同海况,设置相应仿真参数,得出负载在不同海况下主动升沉补偿控制系统的补偿特性,绘制了负载在升沉补偿作用下的位移响应曲线及补偿时电机转速响应曲线,并与无升沉补偿作用下的仿真结果进行对比。仿真结果表明,该主动升沉补偿控制系统具备理想的补偿精度。将主动升沉补偿控制系统应用于海洋绞车进行模拟试验,得到了电驱动海洋绞车主动升沉补偿控制系统在四级模拟海况下的试验数据。试验结果表明该主动升沉补偿控制系统满足补偿能力设计要求。研究可为海洋绞车主动升沉补偿控制系统补偿性能的改进与完善提供参考。     

深海小型履带式机器人转向动力学建模与分析

为预测复杂海底环境下的小型履带式机器人转向运动性能,运用履带与土壤之间的剪切应力-剪切位移关系,考虑履带滑转以及转向离心力因素,并将水中浮力和水阻力参数引入构建履带式机器人深海底质土壤环境下的稳态转向动力学模型。将海底土壤参数、机器人结构参数代入动力学模型迭代求解,分析得到影响海底履带式机器人运动性能的因素。以一款深海小型履带式机器人为研究对象,在动力学仿真软件Recurdyn中构建动力学模型,通过动力学仿真得到的数据与理论计算数据具有较高的一致性,最后通过水池试验对比验证了动力学仿真的正确性。本文提出的稳态动力学模型可以作为海底履带式机器人不同机械结构参数、土壤条件下通过性预测的理论依据。     

基于小波变换选择的海底沉积物声速分析技术

海底沉积物物理特性参数的研究对海洋资源开发、海底工程建设、海地测绘、海洋灾害预报、海底历史研究、航运国防等具有重要意义.它可由对出海采样的样品直接进行土工实验获取,或者经测量得到的声学特性参数表征.目前海底沉积物探测主要以声学测量为主,通过接收透射、反射、折射的声波后提取出声学特性而成,包括压缩波速、切变波速(液体不存在)、声波阻抗、声衰减.针对传统的走时法由于人工读取起跳点造成声速的精确度不高这一特点,引出小波分析方法读取起跳点,应用小波分解原始信号得到的细节信号的模极大值连线来确定原始信号的畸变点,从而确定为接收声信号的起跳点以计算声速.     

浅海聚焦定位中简化地声模型的应用研究

为了提高定位算法的环境宽容性,聚焦法将环境参数纳入了寻优空间。聚焦法虽然降低了对环境测量的要求,但是反演参数的增加也增加了反演的复杂性。基于海底反射特性,用两个参数对海底进行建模。通过标准的反演测试问题对简化地声模型在浅海聚焦定位中的有效性进行了分析。结果表明:基于简化地声模型的聚焦定位是可行的。在获得正确定位结果的同时,随着地声参数个数的减少,匹配场处理的便捷性得到了提高。文中引入的简化地声模型是聚焦问题中参数最少的地声模型,它可以有效减少聚焦定位参数维数以提升反演的便捷性。同时,简化地声模型在参数敏感性和耦合性上有较好的表现,这些优点可以保证定位结果的稳健性。     

含甲烷水合物多孔介质的复电阻率模型对比

在获得含甲烷水合物多孔介质体系阻抗谱参数的基础上,通过计算得到了复电阻率数据,分析了复电阻率参数的频散规律;讨论了3种常用的复电阻率模型(Dias模型、Warburg模型、Cole-Cole模型),并采用实验数据对3种复电阻率模型的参数进行了拟合,进而对各模型的适用性进行了对比和评价。结果表明:Warburg模型对含甲烷水合物多孔介质的复电阻率数据拟合效果最好,该模型可应用于含水合物多孔介质电学特性的进一步研究;Warburg模型的参数与水合物饱和度之间存在明显的对应关系,随着水合物饱和度的增大,模型参数中的零频电阻率和时间常数均单调减小,这为下一步建立基于复电阻率模型参数的水合物饱和度计算模型提供了基础。     

海底沉积物声速经验方程的分析和研究

比较国内外主要研究者提出的海底沉积物声速单参数、双参数和多参数预报经验方程的物理意义和适用性,提出了孔隙度-含水量预报海底沉积物声速新的双参数公式,该式避免了单一参数预报声速经验方程和某些双参数公式中物理意义不明确以及多参数方程复杂性及对提高预报计算能力效果不显著之处.基于理论分析,改进孔隙度-含水量双参数计算公式得到的通用模型具有明确的物理意义,可以通过修改参数适用于不同海域的声速预报,提高了泛化能力,扩大了适用范围.通过对孔隙度、含水量等物理参数的权值分析研究,更加明确了孔隙度是影响海底沉积物声速大小的最关键参数.用台湾海峡北部、南海海域、珠江口大陆架三处的海域沉积物测量数据比较了不同模型,验证了本模型的优越性.     

射线稳定性参数与波导不变量

基于简正波理论的波导不变量在声传播特性描述中已得到广泛应用,而当环境与距离无关或存在轻微扰动时,基于射线理论的声场特性可以用一个新的物理量—射线稳定性参数来描述。本文通过简正波干涉声场数值模拟,通过分析简正波相长干涉形成的能量包传播路径与射线传播路径相互关系,利用简正波水平干涉结构距离上的周期性与射线水平跨距相等的特点,采用简洁方式证明了射线稳定性参数与简正波波导不变量间的等价性,从而在射线和简正波理论中建立了一个新的联系。对远距离射线模型声传播仿真结果的分析表明,与射线传播时间相比,射线稳定性参数作为射线理论的一个新的参数,可有效用于描述声传播特性,并能够反映海洋环境变化,应用于海洋环境参数声学反演。     

基于声场模型的猎雷声呐探测成像仿真方法

针对猎雷声呐对水雷目标探测仿真问题,提出一种基于运动学信息与水下声场传播耦合分析的探测成像仿真方法。利用 Bellhop3D 声场分析方法对水下声信道信号冲击响应进行计算,结合信号复分析方法得到信号传播信道参数以构建声散射模型,以运动耦合方式综合分析声呐搭载平台位置、姿态及速度等因素对回波信号的影响,通过综合考虑上述因素来模拟目标回波信号,从而利用较为真实的等效回波信号进行图像重构。 以高频前视声呐为例,对声呐探测沉底水雷目标情况进行了仿真,结果表明,该方法能够得到高频声呐对沉底水雷目标的探测图像,与实际情况具有一致性,可为进一步构建反水雷相关模拟仿真训练系统提供参考。     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.