Two-Dimensional Large Deformation Finite Element Analysis for the Pulling-up of Plate Anchor

Based on mesh regeneration and stress interpolation from an old mesh to a new one, a large deformation finite element model is developed for the study of the behaviour of circular plate anchors subjected to uplift loading. For the deterruination of the distributions of stress components across a clay foundation, the Recovery by Equilibrium in Patches is extended to plastic analyses. ABAQUS, a commercial finite element package, is customized and linked into our program so as to keep automatic and efficient running of large deformation calculation. The quality of stress interpolation is testified by evaluations of Tresca stress and nodal reaction forces. The complete pulling-up processes of plate anchors buried in homogeneous clay arc simulated, and typical pulling force-displacement responses of a deep anchor and a shallow anchor are compared. Different from the results of previous studies, large deformation analysis is of the capability of estimating the breakaway between the anchor bottom and soils. For deep anchors, the variation of mobilized uplift resistance with anchor settlement is composed of three stages, and the initial buried depths of anchors affect the separation embedment slightly. The uplift bearing capacity of deep anchors is usually higher than that of shallow anchors.     

Behavior of a helical anchor under vertical repetitive loading

Abstract

In the field of ocean engineering, anchors are used for several purposes. This article studies the behavior of a helical anchor embedded in soft marine clay under vertical repetitive loading. Helical anchors are simple steel shafts to which one or more helical plates are attached at regular intervals. The tests are conducted on a model helical anchor installed in a soft marine clay bed prepared in a test tank. Repetitive loading is applied using a pneumatic loading arrangement. Different cyclic load ratios and time periods are adopted. In each test, after the application of repetitive loading, poststatic‐pullout tests are conducted to observe the effect of repetitive loading on anchor behavior. From the test results, it is found that, up to a cyclic load ratio of 55%, there is no reduction in capacity. Instead, there seems to be a marginal increase in capacity and reduction in displacement. The reasons for this behavior are explained in terms of induced changes in strength and deformation behavior of marine clay under repetitive load. However, at higher cyclic load ratios, there seems to be reduction in pullout capacity of the anchor, and the reason for this is explained in terms of strain criteria. From this investigation, it can be concluded that the deep anchor is more suitable to a marine environment than a shallow anchor.     

Loading performance of fish and OMNI-Max anchors in crust-over-soft clays

This paper reports the results from three-dimensional dynamic finite element analysis undertaken to provide insight into the behaviour of the fish and OMNI-max dynamically installed anchors during loading in crust-over-soft clay sediments. Particular attention was focused on the situations where the anchor is embedded to a shallow depth during dynamic installation due to the strong crust layer. Large deformation finite element analyses were carried out using the coupled Eulerian-Lagrangian approach, incoporating the anchor chain effect. Parametric analyses were undertaken varying the initial embedment depth, anchor shape, loading angle, strength ratio between the top and bottom layers. The tracked anchor trajectory confirmed that the diving potential of the fish and OMNI-Max anchors were enhanced by the presence of the crust layer as that somewhat restircted the upward movement. This will be beneficial for many hydrocarbon active regions with layered seabed sediments where the anchor embedment depths during dynamic installation are expected to be low.     

Pullout capacity of embedded suction anchors in sand

An analytical solution has been developed to estimate the horizontal, vertical, and inclined loading pullout capacities of embedded suction anchors in sand. Validation of the analytical solution on pullout capacities has been made through comparisons with the centrifuge model test results. Primary variables for the centrifuge model tests are the depth to the loading point, the load inclination angle, and the addition of flanges. The results indicate that both the horizontal and vertical pullout capacities of the embedded suction anchor in sand increase, reach the peak and then start to decrease as the loading point moves downward. The inclined loading pullout capacity is very much dependent on the load inclination angle and the loading point. The effect of flanges on the pullout capacities is also found to be significant.     

Experimental investigation of the keying process of OMNI-Max anchor

ABSTRACT

The OMNI-Max anchors are newly developed dynamically installed anchors for deep water mooring systems. After installation, the anchor is keyed to a new orientation and position by tensing the attached mooring chain, which is known as the “keying process”. This study conducted 1g model tests to study the trajectories and capacity developments of OMNI-Max anchors in homogeneous and lightly overconsolidated (LOC) clays. A testing arrangement was designed to simulate the anchor keying process with a constant pullout angle at the mudline. A half model anchor which could move against the box glass was used to determine the anchor trajectory in the soil. The effects of padeye offset angle, uplift angle at the mudline, anchor fluke thickness, anchor initial embedment depth, and soil strength on the anchor trajectory and capacity were systematically investigated. Moreover, the critical uplift angle at the padeye and the anchor critical initial embedment depth were discussed. The results indicate that the anchor can dive both in homogeneous and LOC clays under certain conditions. A padeye offset angle of 24–30° is recommended for the OMNI-Max anchor to maintain high capacity and diving trend simultaneously. Besides, the anchor diving trend can be improved with small uplift angles at the mudline and with thick anchor flukes. A critical initial embedment depth of 1.3 times the anchor length is recommended to preclude the anchor from being pulled out.     

Behavior of underwater suction anchor in soil

To study the feasibility and efficiency of underwater suction anchors in soil, the performance of eight model anchors was evaluated in a 30 in. (76·2 cm) by 72 in. (183·0 cm) by 32 in. (81·3 cm) deep test tank. The soil studied were a medium fine sand, a silt and a clay. A gantry-type loading mechanisms was used to apply the vertical breakout force. A pullout rate of approximately 0·1 in/min (0·25 cm/min) was used for all tests.For the range of conditions studied, the test results indicate that the underwater suction anchor is feasible and effective. The breakout behavior of the suction anchors depends upon the anchor geometry including anchor diameter and skirt length, soil strength properties, soil-anchor friction and adhesion, and suction; i.e. the difference between the pressure underneath the porous plate and the ambient pressure. For the anchors and soils tested, the anchor capacity increases linearly with increasing suction provided the anchor skirt length to diameter ratio remains constant. An increase in the anchor capacity results with increasing suction and with increasing internal friction angle of the test soils. To study the results suggest that the underwater suction anchor is particularly useful for short-term anchorage.     

Study on interaction between soil and anchor chain with finite element method

With the development of offshore engineering, deeply embedded anchors are needed to be penetrated to appreciable depth and attached at the pad-eye. The interaction between anchor chain and soil is a very complex process and has not been thoroughly understood yet. In this paper, the finite element method (FEM) was used to study the interaction of soil-chain system. Results of the analysis show that when the attachment point is at a shallow depth, the load-development characteristics of the chain from FEM are in good agreement with that from the model tests and theoretical analysis. But with the depth increment, the results are different obviously in different methods. This phenomenon is resulted from a variety of reasons, and the plastic zone around the chain was studied to try finding the mechanism behind it. It could be seen that the plastic zone extended in different modes at different depths of attachment points. The interaction between the soil and anchor chain makes the load acting on the anchor decrease, but the soil disturbed surrounding the chain increases the anchor failure possibility. When the anchor bearing capacity is evaluated, these two factors should be considered properly at the same time.     

Remotely sensing in detecting the water depths and bed load of shallow waters and their changes

Bed load is a type of sand drift and accumulation on the sea-bed. Sand drift is a very important index to survey the erosion or deposition of coastal zone. The change of water depths indicates the change of bed load in shallow waters. The conventional method for measuring water depth uses the shipboard echo sounder, which is accurate for point-measurement, but is a time-consuming and labor-intensive task. For periodic survey of bathymetry as synoptic scale, the remote sensing method may be a viable alternative. Wave spectrum bathymetric (WSB) method takes advantages of remote sensing to obtain the bathymetry of shallow waters safely, economically and quickly. The WSB method is feasible to detect the change of water depths over coastal zones where water depths are less than about 12 m. This remote sensing method is worthy to be well developed and efficiently applied to change detection of water depths and bed load in shallow waters.     

Numerical investigation on the penetration of gravity installed anchors by a coupled Eulerian–Lagrangian approach

Gravity installed anchors (GIAs) are released from a height of 30–150 m above the seabed, achieving velocities up to 19–35 m/s at the seabed, and embed to depths of 1.0–2.4 times the anchor length. Challenges associated with GIAs include the prediction of anchor initial embedment depth, which determines the holding capacity of the anchor. Based on the coupled Eulerian–Lagrangian approach, a numerical framework is proposed in this paper to predict the embedment depth of GIAs, considering the effects of soil strain rate, soil strain-softening and hydrodynamic drag (modeled using a concentrated force), with the anchor-soil friction described appropriately. GIAs are influenced by the hydrodynamic drag before penetrating into the soil completely, hence the anchor accelerates less than the previous investigations in shallow penetration, even decelerates directly at the terminal impact velocity. The hydrodynamic drag has more influence on OMNI-Max anchors (with an error of ∼4.5%) than torpedo anchors, and the effect becomes more significant with increasing impact velocity. An extensive parametric study is carried out by varying the impact velocity, strain rate and strain-softening parameters, frictional coefficient, and soil undrained shear strength. It is concluded that the dominant factor affecting the penetration is the soil undrained shear strength, then are the impact velocity, strain rate dependency and frictional coefficient, and the minimal is the strain-softening of soil. In addition, although the strain rate dependency is partly compensated by the softening, the anchor embedment depth accounting for the effects of strain rate and strain-softening is lower than that for ideal Tresca soil. Strain rate dependency dominates the combined effects of strain rate and strain-softening in the dynamic installation of GIAs, on which should pay more attention, especially for the calibration of the related parameters and the measured solutions. In the end, the theoretical model based on the bearing resistance method is extended by accounting for the hydrodynamic drag effect.     

Abundance and distribution of meiofauna in the Chukchi Sea

The metazoan meiofauna in the Chukchi Sea were collected from seven shallow water stations(depths ranging 46 to 52 m) and five deep sea stations(depths ranging between 393 and 2 300 m) during the 4th Chinese National Arctic Research Expedition in 2010. The results showed that abundance of meiofauna was higher in shallow water sediments(average of 2 445 ind./(10 cm2)) than in deep sea sediments(407.06 ind./(10 cm2)). A UNIANOVA test for difference between the two different regions was highly significant(F=101.15, p0.01). Nematodes were numerically dominant, representing(96.6±4.6)% of the total meiofaunal abundance at the shallow water stations and(98.90±1.42)% at deep sea stations. The number of higher taxonomic groups and abundance of meiofauna were higher at Stas CC1, CC4, and R06 near the Bering Strait and the continent, than at the rest of the shallow water and deep sea stations. The primary factors causing the differences were concentrations of nutrients P and Si of bottom seawater(R=0.831, p0.003), followed by depth(R=-0.655, p0.05) and sand fractions of sediments(R=0.632, p 0.05). The numbers of meiofauna on the 65 μm and 32 μm sieves were significantly higher than those on the rest of the screens. Differences in numbers of meiofauna retained on screens with different mesh openings were highly significant among all sampling stations(F=31.60, p0.01). The highest numbers of individuals on screens with 32 μm mesh openings were found at deep sea stations. The number of meiofauna in the top 0–1, 1–2, and 2–4 cm segments constituted 84.4% of the total and was significantly higher than those in the bottom 4–6 and 6–10 cm segments(F=15, p0.01).     

Behavior of drag anchor in clay with linearly increasing shear strength under unidirectional and combined loading

Drag anchor is a widely used economical anchor option for offshore floating structures. The anchor behavior under unidirectional loading and combined loading is important for anchor selection. The anchor behavior under combined loading, characterized by the yield envelope, can also be used for the prediction of anchor installation, which is still an issue in anchor design. However, most existing studies on anchor capacity are for plate anchors which focused only on the anchor pullout capacity in soil with uniform shear strength. The behavior of drag anchor under unidirectional and combined loading in soil with linearly increasing shear strength profile is seldom investigated. The current 2D finite element studies investigate the anchor behavior for a horizontal anchor fluke in clay with linearly increasing shear strength under unidirectional vertical, horizontal and rotational loadings first. Then based on the results of anchor unidirectional loading behavior, the yield envelopes for anchor under combined loading for both shallow and deep embedded flukes are studied. The effect of anchor embedment depth, soil non- homogeneity, soil overburden pressure and the soil/anchor interface breakaway conditions are studied to provide insight for drag anchor design.     

Vertical uplift resistance of close-spaced shallow rectangular group anchor plates embedded in sand

Abstract

This study describes an analytical solution for determining the ultimate vertical uplift resistance of a group of two and multiple number of close-spaced shallow rectangular anchor plates embedded horizontally in sand. The analysis was performed by using an upper bound theorem of limit analysis with the employment of the kinematically admissible three-dimensional (3D) rigid wedge collapse mechanisms. Results are obtained in terms of dimensionless uplift factors F_γ and F_q due to the components of soil self-weight and surcharge pressure acting on the ground surface for a wide range of parameters. It was found that the magnitude of uplift factors decreases substantially with a decrease in the clear spacing between the anchors, soil friction angle, and embedment ratio, and an increase in the aspect ratio of anchors. Further, it was noticed that when the clear spacing between the anchors is greater than or equal to the certain critical value, the interaction effect of anchors vanishes and the magnitude of uplift factors associated with a group of anchors becomes equal to that of single isolated anchors. The present solutions are found to compare reasonably well with those theoretical, numerical, and experimental results available in the literature.     

Static pullout resistance of anchor chains in cohesionless soil—laboratory testing

This paper investigates the static pullout resistance of anchor chains embedded into cohesionless soil. The anchor chains, which are made of steel, were buried into Jumunjin sand whose relative density was set to approximately 60%. The anchor chains were horizontally pulled out through a displacement of 70?mm in laboratory model tests. Three different embedment depths and seven different numbers of chain links were adopted. The pullout resistance of the anchor chains was found to increase with increasing embedment depth and the number of anchor chain links. The measured resistance was significantly higher than the calculated frictional resistance, implying that the passive resistance at the front of the anchor chain significantly contributes to the pullout resistance. The contribution of the passive resistance tends to decrease with increasing number of chain links.     

南海北部陆坡深水区浅层天然气藏特征

南海北部陆坡深水区的浅层天然气藏是一种伴随天然气水合物的新型油气藏, 具有埋藏浅、规模大的特点, 其埋藏深度一般小于300m。浅层天然气藏由深部裂解气沿断裂上升被天然气水合物封盖而形成, 识别似海底反射(BSR)是寻找浅层天然气藏有效方法。浅层天然气藏的气源主要有热解气、生物气和混合气, 陆坡张性断裂是气体运移的主要通道, 水合物下部的砂层是浅层天然气藏的主要储集层, 水合物层则是封盖层。从南海发现的天然气水合物分布特征看, 浅层天然气藏在陆坡深水区广泛分布且气藏厚度大, 潜在资源量非常可观, 是一种新型的开采成本相对低廉的油气藏。     

Numerical analysis of suction embedded plate anchors in structured clay

As offshore energy developments move towards deeper water, moored floating production facilities are increasingly preferred to fixed structures. Anchoring systems are therefore of great interest to engineers working on deep water developments. Suction embedded plate anchors (SEPLAs) are rapidly becoming a popular solution, possessing a more accurate and predictable installation process compared to traditional alternatives. In this paper, finite element analysis has been conducted to evaluate the ultimate pullout capacity of SEPLAs in a range of post-keying configurations. Previous numerical studies of anchor pullout capacity have generally treated the soil as an elastic-perfectly plastic medium. However, the mechanical behaviour of natural clays is affected by inter-particle bonding, or structure, which cannot be accounted for using simple elasto-plastic models. Here, an advanced constitutive model formulated within the kinematic hardening framework is used to accurately predict the degradation of structure as an anchor embedded in a natural soft clay deposit is loaded to its pullout capacity. In comparison with an idealised, non-softening clay, the degradation of clay structure due to plastic strains in the soil mass results in a lower pullout capacity factor, a quantity commonly used in design, and a more complex load–displacement relationship. It can be concluded that clay structure has an important effect on the pullout behaviour of plate anchors.     

Analysis Procedure of the Cyclic Bearing Capacity for Suction Anchors in Soft Clays

This article presents a procedure to calculate the bearing capacity of suction anchors subjected to inclined average and cyclic loads at the optimal load attachment point using the undrained cyclic shear strength of soft clays based on the failure model of anchors proposed by Andersen et al. The constant average shear stress of each failure zone around an anchor is assumed and determined based on the static equilibrium condition for the procedure. The cyclic shear strength of each failure zone is determined based on the average shear stress. The cyclic bearing capacity is finally determined by limiting equilibrium analyses. Thirty-six model tests of suction anchors subjected to inclined average and cyclic loads were conducted, which include vertical and lateral failure modes. Model test results were predicted using the procedure to verify its feasibility. The average relative error between predicted and test results is 1.7%, which shows that the procedure can be used to calculate the cyclic bearing capacity of anchors with optimal loading. Test results also showed that the anchor was still in vertical failure mode under combined average and cyclic loads if an anchor was in vertical failure mode under static loads. The anchor failure would depend on the vertical resistance degradation under cyclic loads if an anchor was in lateral failure mode under static loads. Cyclic bearing capacities associated with the number of load cycles to failure of 1000 were about 75% and 80% of the static bearing capacity for vertical failure anchors and lateral failure anchors, respectively.     

Puzzling mass movement features in the Navarinsky Canyon head,Bering Sea

Two types of morphologic features in the head of Navarinsky Canyon are attributed to mass movement of near-surface sediment. A series of pull-aparts is located downslope of large sand waves. These pull-aparts, possibly induced by liquefaction, affect the upper 5 to 10 m of sandy sediment (water depths 350 to 600 m) on a 1^o slope. A hummocky elongate mound of muddy sand (water depths 550 to 800 m) contains chaotic internal reflectors to a subbottom depth of 30 to 40 m and possibly is the product of a shallow slide. We speculate that Holocene seismicity is the likely triggering mechanism.     

Analytical study on comprehensive behaviors of drag anchors in the seabed

Attributed to good performance in the seabed, drag anchors are adopted as an effective anchoring solution in deepwater mooring systems. This type of anchors is drag installed, companying with comprehensive behaviors during movement of the anchor in the seabed, which make the anchor trajectory and therefore the final embedment position difficult to be predicted. On the basis of the mechanical model and analytical procedure, an analytical method is proposed for exploring comprehensive behaviors of drag anchors in both clay and sand. The anchor behaviors are classified as keying, pulling out and diving. The bearing capacity and the trajectory of the anchor can be predicted through the combination of the three behaviors. By comparing analytical predictions with experimental data and other predictions, the efficiency and veracity of the theoretical model are validated. A parametric study is also performed to investigate the effects of different parameters, and to further understand the comprehensive anchor behaviors in the seabed. The present work provides an efficient theoretical tool for analyzing comprehensive behaviors of drag anchors in either clayey or sandy seabed.     

Interaction of ocean waves with floating and submerged horizontal flexible structures in three-dimensions

A three-dimensional general mathematical hydroelastic model dealing with the problem of wave interaction with a floating and a submerged flexible structure is developed based on small amplitude wave theory and linear structural response. The horizontal floating and submerged flexible structures are modelled with a thin plate theory. The linearized long wave equations based on shallow water approximations are derived and results are compared. Three-dimensional Green’s functions are derived using fundamental source potentials in water of finite and infinite depths. The expansion formulae associated with orthogonal mode-coupling relations are derived based on the application of Fourier transform in finite and infinite depths in case of finite width in three-dimensions. The usefulness of the expansion formula is demonstrated by analysing a physical problem of surface gravity wave interaction with a moored finite floating elastic plate in the presence of a finite submerged flexible membrane in three-dimensions. The numerical accuracy of the method is demonstrated by computing the complex values of reflected wave amplitudes for different modes of oscillation and mooring stiffness. Further, the effect of compressive force and modes of oscillations on a free oscillation hydroelastic waves in a closed channel of finite width and length for floating and submerged elastic plate system is analysed.     

Discussion of “A function to determine wavelength from deep in to shallow water based on the length of the cnoidal wave at breaking” by J.P. Le Roux

An empirical modification to the Airy equation for wave celerity reduces to the expression for solitary waves in shallow water whilst retaining its usual form for deep water. The equation yields celerities in reasonable agreement with those for cnoidal waves in intermediate water depths. In this aspect, it is similar to the work described by Le Roux [Le Roux, J.P., 2007. A function to determine wavelength from deep into shallow water based on the length of the cnoidal wave at breaking. Coastal Engineering 54, 770–774]. The empirical modification has been widely applied in computer programs over the past 30 years.