装配式人工消能塑性铰框架-摇摆墙抗震性能研究

为提高装配式钢筋混凝土(RC)框架结构的抗震性能,并针对震后梁、柱构件损伤严重等问题,提出一种基于人工塑性消能铰的装配式混凝土框架-摇摆墙结构.人工消能塑性铰即梁、柱构件在梁端采用机械铰及附加耗能钢板连接的构造,基于该构造的框架结合底部铰接的剪力墙,形成人工消能塑性铰框架-摇摆墙结构.使用OpenSEES软件建立了人工...     

扩孔螺栓连接型消能梁段的力学模型及参数研究

当前国家对建筑结构的抗震性能和震后功能恢复能力提出了更高要求。基于短剪切型消能梁段的受剪屈服特性和剪切扩孔型螺栓连接的受剪滑移性能,提出一种新型扩孔螺栓连接型消能梁段,可有效增大消能梁段的延性和耗能能力并同时减小消能梁段的损伤,使带扩孔螺栓连接型消能梁段的新型Y形偏心支撑结构更好地适应当前要求。采用有限元方法详细分析扩孔螺栓连接型消能梁段的滞回性能、破坏模式和耗能机理,由此得到其骨架曲线和力学模型,并阐述其力学模型的影响参数,为相应偏心支撑结构的设计和分析提供理论依据。     

摇摆墙-框架体系的抗震损伤机制控制研究

合理有效的损伤机制控制是提高建筑结构抗震性能的重要措施.本文在总结现有各种抗震结构体系损伤机制的基础上,研究了摇摆墙-框架结构体系的损伤机制控制原理与控制效果,给出了摇摆墙刚度的确定方法,比较了摇摆墙-框架结构体系与传统的延性框架结构体系、框架-剪力墙结构体系抗震性能的差别,指出了摇摆墙-框架结构体系的优越性.通过对一...     

安装粘弹性转角阻尼器的海洋平台—摇摆墙体系抗震性能分析

在海洋平台摇摆墙体系基础上,在摇摆墙底部的铰接点处安装一粘弹性转角阻尼器,进行被动消能结构振动控制,利用ANSYS进行地震荷载作用下的抗震性能验算,并对阻尼器的刚度和阻尼参数进行了分析。结果表明,在摇摆墙底部施加的转角阻尼器能显著降低结构的地震反应。     

长周期地震动作用下RID-巨-子结构消能控制体系减震性能研究

为了验证旋转惯容阻尼器(RID)对巨-子结构体系在长周期地震动作用下的减震效果,基于强震动观测数据比较了近断层速度脉冲型地震动和远场类谐和地震动这两类长周期地震动的特点,通过建立RID-巨-子结构消能控制体系的振动微分方程,对比分析了两类长周期地震动对RID-巨-子结构消能控制体系和巨-子结构抗震体系地震响应的影响差异。结果表明,相对于巨-子结构抗震体系,RID-巨-子结构消能控制体系能有效减小结构体系在长周期地震动作用下的地震响应,减震效果明显。     

装配式混凝土金属消能减震连接体系抗震性能分析研究

为了研究装配式混凝土金属消能减震连接体系的抗震性能,对金属消能减震连接体系和普通预制装配式框架进行了数值仿真分析,分析了消能器不同设计参数对该体系抗震性能的影响。分析结果表明:金属消能减震连接体系的抗震性能优于普通预制装配式框架,屈服位移有显著提高,较好的延缓了梁端的破坏,对梁端保护作用明显,并且有效的解决了梁端后浇区施工困难的问题;金属消能器腹板高度越小耗能效果越好,但初始刚度及承载力也越小;翼缘板厚度越小消能器越早屈服耗能,但过小的翼缘板厚度会导致耗能能力不足,并且应变过大会导致其与梁柱连接部位被破坏;随着消能器高度的增加,构件跨中弯矩越大,也越早屈服耗能,但过大的消能器高度会导致其弯曲变形严重。     

加装SLVD的预制装配式混凝土消能减震框架抗震性能分析

为研究扇形铅黏弹阻尼器(SLVD)对预制装配式混凝土(PC)框架抗震性能的提升效果和其设计参数对PC框架抗震性能的影响规律,建立Abaqus精细化有限元模型,与试验结果对比验证模型正确性。对比加装SLVD的PC消能框架与RC框架抗震性能的差异,分析不同铅芯直径、橡胶硬度和扇形半径三个关键设计参数对PC消能框架抗震性能的影响。研究结果表明:SLVD在PC消能框架中起“耗能腋撑”作用;铅芯直径对整体结构抗震性能影响较大,随铅芯直径增大,结构刚度、承载能力和耗能能力均有所提高;橡胶硬度对整体结构抗震性能影响较小;铅芯屈服区域随扇形半径增大而减小,但可提高整体结构的承载能力。     

筒中筒结构内部摩擦连接消能减震体系的研究

提出利用筒中筒结构内筒和外筒的相对运动带动耗能装置耗能的的筒中筒结构内部摩擦连接消能减震体系。该体系将结构的内筒和框筒用专门设计的摩擦连接装置连接,罕遇地震下摩擦连接装置滑移产生滞回耗能。文中阐明了该体系的消能减震原理和构造特点,并通过对一栋40层筒中筒结构进行有限元分析,验证了该体系具有良好的抗震性能,可供工程实践参考。     

摇摆墙刚度对框架摇摆墙结构抗震性能的影响分析

为研究摇摆墙刚度对框架摇摆墙结构抗震性能的影响,对1个4层钢筋混凝土框架结构模型,用有限元软件SAP2000对附加不同刚度的摇摆墙结构进行了静力非线性分析。分析结果表明:随着摇摆墙刚度的增大可以逐渐改善框架的抗震性能,使框架变形更加均匀,层间位移角更趋于一致。但刚度增加到一定程度后,其值进一步增大时结构的抗震性能趋于稳定。对于本文的结构模型摇摆墙与框架的刚度比小于1.27%时,对框架的破坏机制影响很小。摇摆墙的刚度比大于2.48%时,开始改变框架的破坏机制,逐渐从层破坏机制变为整体破坏机制。摇摆墙的刚度比大于6.81%时,结构具有稳定的整体破坏机制。     

不同类型地震动作用下自复位摇摆桥梁延性需求谱研究

自复位摇摆桥梁的损伤和残余位移小,具有良好的震后可恢复性。文中以自复位摇摆桥梁为研究对象,对不同类型地震动作用下的结构的延性需求谱及其影响因素进行研究。选用FEMA P695推荐的100条典型地震动作为输入,并划分为远场地震动、近场脉冲地震动以及近场无脉冲地震动。研究结果表明,近场脉冲地震动作用下的结构的延性需求最大,设计时需考虑近场脉冲地震动的影响;随着强度折减系数R的增大,结构的延性需求显著增加,设计时不宜采用较高的强度折减系数;增加刚度比α和耗能系数β能在一定周期范围内减小结构的延性需求;阻尼比ξ在0.01～0.05范围内对延性需求的影响基本可以忽略。     

罕遇地震作用下的框架-摇摆刚架结构体系动力可靠度研究

针对钢筋混凝土框架结构的受力特点,采用增设摇摆刚架的抗震设计方法,以提高罕遇地震下建筑结构的安全性。建立了框架一摇摆刚架结构体系的计算模型,结合状态空间法与虚拟激励法,求解结构的平稳随机响应,并根据计算所得随机响应对框架一摇摆刚架体系的动力可靠度进行分析。以西部地区某已建成的6层框架结构为算例,探讨了罕遇地震作用下不同刚度比的摇摆刚架对新结构体系动力可靠度的影响。结果表明,通过增设不同刚度比的摇摆刚架,可以有效协调结构体系的变形模式,充分发挥结构的耗能能力,降低整体结构的条件失效概率。     

Modeling of energy dissipation in structural devices and foundation soil during seismic loading

Though rocking shallow foundations could be designed to possess many desirable characteristics such as energy dissipation, isolation, and self-centering, current seismic design codes often avoid nonlinear behavior of soil and energy dissipation beneath foundations. This paper compares the effectiveness of energy dissipation in foundation soil (during rocking) with the effectiveness of structural energy dissipation devices during seismic loading. Numerical simulations were carried out to systematically study the seismic energy dissipation in structural elements and passive controlled energy dissipation devices inserted into the structure. The numerical model was validated using shaking table experimental results on model frame structures with and without energy dissipation devices. The energy dissipation in the structure, drift ratio, and the force and displacement demands on the structure are compared with energy dissipation characteristics of rocking shallow foundations as observed in centrifuge experiments, where shallow foundations were allowed to rock on dry sandy soil stratum during dynamic loading. For the structures with energy dissipating devices, about 70–90% of the seismic input energy is dissipated by energy dissipating devices, while foundation rocking dissipates about 30–90% of the total seismic input energy in foundation soil (depending on the static factor of safety). Results indicate that, if properly designed (with reliable capacity and tolerable settlements), adverse effects of foundation rocking can be minimized, while taking advantage of the favorable features of foundation rocking and hence they can be used as efficient and economical seismic energy dissipation mechanisms in buildings and bridges.     

Seismic performance of hybrid ductile‐rocking braced frame system

A new hybrid ductile‐rocking seismic‐resistant design is proposed which consists of a code‐designed buckling‐restrained braced frame (BRBF) that yields along its height and also partially rocks on its foundation. The goal of this system is to cost‐effectively improve the performance of BRBFs, by reducing drift concentrations and residual deformations, while taking advantage of their large ductility and their reliable limit on seismic forces and accelerations along a building's height. A lock‐up device ensures that the full code‐compliant lateral strength can be achieved after a limited amount of column uplift, and supplemental energy dissipation elements are used to reduce the rocking response. This paper outlines the mechanics of the system and then presents analyses on rocking frames with both ductile and elastic braces in order to highlight the large higher mode demands on elastic rocking frames. A parametric study using nonlinear time‐history analysis of BRBF structures designed according to the proposed procedure for Los Angeles, California is then presented. This study investigates the system's seismic response and the effect of different energy dissipation element properties and allowable base rotation values before the lock‐up is engaged. Finally, the effect of vertical mass modeling on analysis results was investigated. These studies demonstrated that the hybrid ductile‐rocking system can in fact improve the global peak and residual deformation response as well as reduce brace damage. This enhanced performance could eliminate the need for expensive repairs or demolition that are otherwise to be expected for conventional ductile fixed base buildings that sustain severe damage.     

Seismic performance evaluation of an infilled rocking wall frame structure through quasi-static cyclic testing

Earthquake investigations have illustrated that even code-compliant reinforced concrete frames may suffer from soft-story mechanism. This damage mode results in poor ductility and limited energy dissipation. Continuous components offer alternatives that may avoid such failures. A novel infilled rocking wall frame system is proposed that takes advantage of continuous component and rocking characteristics. Previous studies have investigated similar systems that combine a reinforced concrete frame and a wall with rocking behavior used. However, a large-scale experimental study of a reinforced concrete frame combined with a rocking wall has not been reported. In this study, a seismic performance evaluation of the newly proposed infilled rocking wall frame structure was conducted through quasi-static cyclic testing. Critical joints were designed and verified. Numerical models were established and calibrated to estimate frame shear forces. The results evaluation demonstrate that an infilled rocking wall frame can effectively avoid soft-story mechanisms. Capacity and initial stiffness are greatly improved and self-centering behavior is achieved with the help of the infilled rocking wall. Drift distribution becomes more uniform with height. Concrete cracks and damage occurs in desired areas. The infilled rocking wall frame offers a promising approach to achieving seismic resilience.     

粘滞阻尼耗能连梁的超高层结构减震性能研究

连梁作为剪力墙结构中的抗震第一道防线,其承载力和耗能能力对整体结构的抗震性能有重要影响。本文提出在连梁中附设粘滞阻尼器,利用阻尼器发生竖向剪切变形而耗能。结合实际工程研究粘滞阻尼耗能连梁的性能,采用ETABS和PERFORM-3D软件对粘滞阻尼耗能连梁结构与传统连梁结构进行有限元模拟对比分析,并对粘滞阻尼耗能连梁的各项最优参数进行研究。结果表明:粘滞阻尼耗能连梁充分发挥耗能作用,整体结构具有良好的抗震性能,与传统连梁结构相比,主体结构的弹性耗能得到明显降低。平面布置方式、竖向布置方式、阻尼器参数的选取对附设粘滞阻尼耗能连梁的框架-核心筒结构减震效果影响较大,合理选择这些参数可以使耗能结构减震效果最优。     

A finite element model for seismic response analysis of deformable rocking frames

A new finite element model to analyze the seismic response of deformable rocking bodies and rocking structures is presented. The model comprises a set of beam elements to represent the rocking body and zero‐length fiber cross‐section elements at the ends of the rocking body to represent the rocking surfaces. The energy dissipation during rocking motion is modeled using a Hilber–Hughes–Taylor numerically dissipative time step integration scheme. The model is verified through correct prediction of the horizontal and vertical displacements of a rigid rocking block and validated against the analytical Housner model solution for the rocking response of rigid bodies subjected to ground motion excitation. The proposed model is augmented by a dissipative model of the ground under the rocking surface to facilitate modeling of the rocking response of deformable bodies and structures. The augmented model is used to compute the overturning and uplift rocking response spectra for a deformable rocking frame structure to symmetric and anti‐symmetric Ricker pulse ground motion excitation. It is found that the deformability of the columns of a rocking frame does not jeopardize its stability under Ricker pulse ground motion excitation. In fact, there are cases where a deformable rocking frame is more stable than its rigid counterpart. Copyright © 2016 John Wiley & Sons, Ltd.     

钢筋混凝土框架抗震结构地震能量分布及耗散研究

基于能量平衡原理,对多层钢筋混凝土框架结构的地震输入能量的分布及耗散规律进行了研究。选用8条天然地震波和2条人工波,运用Perform-3D软件,对多层钢筋混凝土框架结构模型在7度罕遇地震作用下的弹塑性能量进行数值仿真计算。计算了钢混框架结构在不同地震波下的地震总输入能量、滞回耗能、阻尼耗能以及滞回耗能占总耗能的比例时程,分析了地震能量在各分量中的分布及分配规律;分析了阻尼比和延性比对地震输入能量的影响,确定了滞回耗能随阻尼比和延性比的变化规律;研究了钢筋混凝土框架结构梁柱构造和竖向侧移刚度变化对地震输入能及其分量的影响,确定了多层钢筋混凝土框架结构滞回耗能沿竖向的分布规律及沿横向在框架构件中的分配,研究了框架结构存在薄弱层情况下的滞回耗能的分布规律。揭示了多自由度钢筋混凝土框架结构地震输入能量及其分布规律,可为基于能量平衡原理的抗震设计理论在工程实际中的运用提供有益的参考。     

消能减震技术用于C类框架学校建筑提高一度抗震设防加固的探讨

针对既有的C类框架学校建筑提高一度抗震设防的加固目标,从地震作用计算、结构抗震验算和抗震构造措施等方面详细分析了其中的加固难点,指出了应用传统抗震加固方法的一些不足之处,探讨了应用消能减震技术进行结构提高一度抗震设防加固的可行性;并以某C类框架学校建筑加固工程为实例,从减震控制效果分析、弹塑性变形验算、消能部件影响评价、抗震构造措施核查4个方面论证了消能减震加固方法的有效性和可操作性。结果表明,消能减震技术在C类框架学校建筑抗震加固中具有一定的应用优势,不但能有效控制结构的地震响应,而且依据减震效果可以适当降低结构的抗震构造要求。因此,只要通过合理的消能减震加固设计,再辅以额外的局部加强处理,完全可以实现C类框架学校建筑提高一度抗震设防的加固目标需求。     

Seismic behaviour of multistorey RC wall–frame system versus bare ductile frame system

The wall–frame systems have many known advantages, namely increase of the system's lateral strength and stiffness thereby allowing for a good tangential inter‐storey drift control, and the retention of a satisfactory energy dissipation capacity. However, rocking of the wall could occur as a result of uplifting wall base or concentrated plastic hinge deformations. Problems arising from this phenomenon have significant impact on the system behaviour and hence require extended study. This paper focuses on the wall‐rocking phenomenon due to the concentrated plastic hinge rotation at the wall base. To facilitate a comprehensive evaluation, a six‐storey three‐bay RC wall–frame structure is investigated with comparison to a bare ductile frame by means of earthquake simulation tests. The results revealed that, despite a superior performance over the ductile frame under low to moderate seismic actions, the wall–frame structure deteriorated more rapidly than the bare frame during advanced inelastic response. The increasingly significant rocking of the wall resulted in severe material damage at localized critical regions. Mitigating the wall rocking is seen to be a key to the further improvement of the system performance, and the extent to which this may be achieved by incorporating the three‐dimensional effects is explicitly illustrated by an analytical evaluation. Copyright © 2001 John Wiley & Sons, Ltd.     

运用防屈曲支撑的混凝土框架结构的抗震性能研究

简要介绍地震安全社区的实现途径以及防屈曲支撑的构成和性能参数。运用ABAQUS软件对有无安装防屈曲支撑的钢筋混凝土框架模型进行动力时程分析,总结分析防屈曲支撑对钢筋混凝土框架结构的减震效果。结果表明,防屈曲支撑能大大降低钢筋混凝土框架结构在罕遇地震作用下的层间位移角,提高建筑物抗震性能,使地震安全社区中抗震设防烈度为Ⅶ度的建筑物能够抵御Ⅷ度罕遇地震。