Experimental study on suspended sediment concentration and its vertical distribution under spilling breaking wave actions in silty coast

In this paper,flume experiments are focused on sediment transport inside and outside the surf zone.According to the energy dissipation balance principle of sediment-laden flow and the similarity between energy dissipation of spilling breaking wave and hydraulic jump,formulas are proposed to predict time averaged suspended sediment concentration under both non-breaking and breaking waves.Assuming that the sediment diffusion coefficient,which is related with energy dissipation,is proportional to water depth,formulas are proposed to predict close-to-bed suspended sediment concentration and vertical distribution of suspended sediment under spilling breaking waves,and the prediction shows a good agreement with the measurement.     

Characteristics of turbulent boundary layers over a rough bed under saw-tooth waves and its application to sediment transport

A large number of studies have been done dealing with sinusoidal wave boundary layers in the past. However, ocean waves often have a strong asymmetric shape especially in shallow water, and net of sediment movement occurs. It is envisaged that bottom shear stress and sediment transport behaviors influenced by the effect of asymmetry are different from those in sinusoidal waves. Characteristics of the turbulent boundary layer under breaking waves (saw-tooth) are investigated and described through both laboratory and numerical experiments. A new calculation method for bottom shear stress based on velocity and acceleration terms, theoretical phase difference, φ and the acceleration coefficient, a_c expressing the wave skew-ness effect for saw-tooth waves is proposed. The acceleration coefficient was determined empirically from both experimental and baseline k–ω model results. The new calculation has shown better agreement with the experimental data along a wave cycle for all saw-tooth wave cases compared by other existing methods. It was further applied into sediment transport rate calculation induced by skew waves. Sediment transport rate was formulated by using the existing sheet flow sediment transport rate data under skew waves by Watanabe and Sato [Watanabe, A. and Sato, S., 2004. A sheet-flow transport rate formula for asymmetric, forward-leaning waves and currents. Proc. of 29th ICCE, ASCE, pp. 1703–1714.]. Moreover, the characteristics of the net sediment transport were also examined and a good agreement between the proposed method and experimental data has been found.     

Sand transport under combined current and wave conditions: A semi-unsteady,practical model

For the general purposes of morphodynamic computations in coastal zones, simple formula-based models are usually employed to evaluate sediment transport. Sediment transport rates are computed as a function of the bottom shear stress or the near bed flow velocity and it is generally assumed that the sediment particles react immediately to changes in flow conditions. It has been recognized, through recent laboratory experiments in both rippled and plane bed sheet flow conditions that sediment reacts to the flow in a complex manner, involving non-steady processes resulting from memory and settling/entrainment delay effects. These processes may be important in the cross-shore direction, where sediment transport is mainly caused by the oscillatory motions induced by surface short gravity waves.The aim of the present work is to develop a semi-unsteady, practical model, to predict the total (bed load and suspended load) sediment transport rates in wave or combined wave-current flow conditions that are characteristic of the coastal zone. The unsteady effects are reproduced indirectly by taking into account the delayed settling of sediment particles. The net sediment transport rates are computed from the total bottom shear stress and the model takes into account the velocity and acceleration asymmetries of the waves as they propagate towards the shore.A comparison has been carried out between the computed net sediment transport rates with a large data set of experimental results for different flow conditions (wave-current flows, purely oscillatory flow, skewed waves and steady currents) in different regimes (plane bed and rippled bed) with fine, medium and coarse uniform sand. The numerical results obtained are reasonably accurate within a factor of 2. Based on this analysis, the limits and validity of the present formulation are discussed.     

Modeling sediment transport in the swash zone: A review

A critical review of conceptual and mathematical models developed in recent decades on sediment transport in the swash zone is presented. Numerous studies of the hydrodynamics and sediment transport in the swash zone in recent years have pointed out the importance of swash processes in terms of science advancement and practical applications. Evidently, the hydrodynamics of the swash zone are complex and not fully understood. Key hydrodynamic processes include both high-frequency bores and low-frequency infragravity motions, and are affected by wave breaking and turbulence, shear stresses and bottom friction. The prediction of sediment transport that results from these complex and interacting processes is a challenging task. Besides, sediment transport in this oscillatory environment is affected by high-order processes such as the beach groundwater flow. Most relationships between sediment transport and flow characteristics are empirical, based on laboratory experiments and/or field measurements. Analytical solutions incorporating key factors such as sediment characteristics and concentration, waves and coastal aquifer interactions are unavailable. Therefore, numerical models for wave and sediment transport are widely used by coastal engineers. This review covers mechanisms of sediment transport, important forcing factors, governing equations of wave-induced flow, groundwater interactions, empirical and numerical relations of cross-shore and longshore sediment transport in the swash zone. Major advantages and shortcomings of various numerical models and approaches are highlighted and reviewed. These will provide coastal modelers an impetus for further detailed investigations of fluid and sediment transport in the swash zone.     

Large-scale experiments on beach profile evolution and surf and swash zone sediment transport induced by long waves,wave groups and random waves

New large-scale laboratory data are presented on the influence of long waves, bichromatic wave groups and random waves on sediment transport in the surf and swash zones. Physical model testing was performed in the large-scale CIEM wave flume at UPC, Barcelona, as part of the SUSCO (swash zone response under grouping storm conditions) experiment in the Hydralab III program (Vicinanza et al., 2010). Fourteen different wave conditions were used, encompassing monochromatic waves, bichromatic wave groups and random waves. The experiments were designed specifically to compare variations in beach profile evolution between monochromatic waves and unsteady waves with the same mean energy flux. Each test commenced with approximately the same initial profile. The monochromatic conditions were perturbed with free long waves, and then subsequently substituted with bichromatic wave groups with different bandwidth and with random waves with varying groupiness. Beach profile measurements were made at half-hourly and hourly intervals, from which net cross-shore transport rates were calculated for the different wave conditions. Pairs of experiments with slightly different bandwidth or wave grouping show very similar net cross-shore sediment transport patterns, giving high confidence to the data set. Consistent with recent small-scale experiments, the data clearly show that in comparison to monochromatic conditions the bichromatic wave groups reduce onshore transport during accretive conditions and increase offshore transport during erosive conditions. The random waves have a similar influence to the bichromatic wave groups, promoting offshore transport, in comparison to the monochromatic conditions. The data also indicate that the free long waves promote onshore transport, but the conclusions are more tentative as a result of a few errors in the test schedule and modifications to the setup which reduced testing time. The experiments suggest that the inclusion of long wave and wave group sediment transport is important for improved near-shore morphological modeling of cross-shore beach profile evolution, and they provide a very comprehensive and controlled series of tests for evaluating numerical models. It is suggested that the large change in the beach response between monochromatic conditions and wave group conditions is a result of the increased significant and maximum wave heights in the wave groups, as much as the presence of the forced and free long waves induced by the groupiness. The equilibrium state model concept can provide a heuristic explanation of the influence of the wave groups on the bulk beach profile response if their effective relative fall velocity is larger than that of monochromatic waves with the same incident energy flux.     

Magnitude and cross-shore distribution of bed return flow measured on natural beaches

Field measurements of cross-shore currents 0.25 m from the bed were made on two natural beaches under a range of incident wave conditions. The results indicated the presence of a relatively strong, offshore-directed mean current, both within and seaward of the surf zone. Typical velocities within the surf zone were of the order of 0.2–0.3 m/s. This bed return flow, or “undertow”, represents a mass conservation response, returning water seaward that was initially transported onshore in the upper water column, primarily above the trough of the incident waves. The measurements demonstrated that the bed return flow velocity increases with the incident wave height. In addition, the crossshore distribution of the bed return flow is characterised by a mid-surf zone maximum, which exhibits a strong decrease in velocity towards the shoreline and a more gradual decay in the offshore direction. Several bed return flow models based on mass continuity were formulated to predict the cross-shore distribution of the bed return flow under an irregular wave field and were compared with the field data. Best agreement was obtained using shallow water linear wave theory, after including the mass transport associated with unbroken waves. The contribution of the unbroken waves enables net offshore-directed bottom currents to persist outside the region of breaking waves, providing a mechanism, other than rip currents, to transport sediment offshore beyond the surf zone.     

Numerical simulation of breaking wave generated sediment suspension and transport process based on CLSVOF algorithm

The sediment suspension and transport process under complex breaking wave situation is investigated using large eddy simulation （abbreviated as LES hereafter） method. The coupled level set （LS） and volume of fluid （VOF） method is used to accurately capture the evolution of air？water interface. The wall effect at the bottom is modeled based on the wave friction term while the complicate bottom boundary condition for sediment is tackled using Chou and Fringer’s sediment erosion and deposition flux method. A simulation is carried out to study the sediment suspension and transport process under periodic plunging breaking waves. The comparison between the results by CLSVOF method and those obtained by the LS method is given. It shows that the latter performs as well as the CLSVOF method in the pre-breaking weak-surface deformation situation. However, a serious mass conservation problem in the later stages of wave breaking makes it inappropriate for this study by use of the LS method and thus the CLSVOF method is suggested. The flow field and the distribution of suspended sediment concentration are then analyzed in detail. At the early stage of breaking, the sediment is mainly concentrated near the bottom area. During the wave breaking process, when the entrapped large-scale air bubble travels downward to approach the bottom, strong shear is induced and the sediment is highly entrained.     

Non-linear propagation of unidirectional wave fields over varying topography

The present study aims at investigating the non-linear triad interaction process affecting shoaling surface gravity wave fields. The triad interaction phenomenon being enhanced towards the shore, the domain of study is extended up to the surf zone. Three 1D non-linear wave models (one phase-resolving and two phase-averaged spectral models) have been implemented and compared to laboratory experiments performed in a wave flume. This set of models includes two existing models and a new one which has been developed in the frame of this work. The models include a breaking dissipation term based on the parametrical model of Battjes and Janssen [Battjes, J.A., Janssen, P.A.E.M., 1978. Energy loss and set-up due to breaking of random waves. Proc. 16th Int. Conf. Coastal Eng. (ASCE), Vol. 1, pp. 569–587.]. The investigations concern the evolution of variance spectra, spectral significant wave height and mean period over a barred bathymetric profile. In addition, the performances of the different models are analysed by computing the spectral source term for triad interactions. We found that all models are able to reproduce the main features of non-linear mechanisms affecting a wave field in the near-shore zone. The phase-resolving model gives the most accurate results for non-breaking situations. It correctly reproduces the non-linear coupling effect in decreasing water depths due to wave–wave interactions, as well as the harmonic release after a bar. However, the model is computationally time-consuming. The CPU time is considerably reduced using phase-averaged models. They give satisfactorily results on harmonic generation. However, they do not reproduce the release of harmonics as water depth increases. In breaking conditions, the variance spectra undergo significant changes under the combined effects of non-linear energy transfers and dissipation. The depth-induced wave breaking model included in the equations provides a good estimate of the energy decay in the surf zone.     

Threshold of motion of coarse-grained sediment under waves in shallow water

This paper considers the threshold of motion of sediment in shallow coastal waters under breaking and non-breaking waves. A simple model, representing conditions at the fluid/sediment interface, is developed. The representation of a breaking wave is based on bore theory, and the shear stress at the bed is based on the friction formula of O'Connor and Yoo. A threshold formula is presented based on the use of energy dissipation. The threshold data is also related to the Shields threshold criterion.     

卷破波作用下沙质岸滩剖面形态判别式初探

通过波浪水槽实验,开展不同类型波浪作用下的沙质岸滩演化规律研究工作。本次实验研究不考虑比尺,采用1:10与1:20组成的复合沙质斜坡对岸滩进行概化,选取规则波和椭圆余弦波两种典型波浪作用,对波浪的传播、变形和破碎、上爬、回落过程以及波浪作用前后沙质岸滩床面地形进行了观测,探讨波浪作用下沙质岸滩剖面演化规律。本文实验工况中,规则波作用下,岸滩剖面呈现出沙坝剖面和滩肩剖面,椭圆余弦波作用下的岸滩剖面均呈滩肩形态,发现岸滩剖面形态不仅与波浪作用类型、强度、周期等因素相关,还与波浪破碎的强度等因素有关。通过对实验过程中现象的进行观察和分析,引入了卷破波水舌冲击角的概念。对波浪卷破破碎后形成的水流挟沙运动与岸滩剖面形态的关系进行定性分析,对水舌冲击角与Irribarren参数之间的关系进行定量分析,基于Irribarren参数与岸滩剖面形态的关系初步建立了波浪作用下沙质岸滩剖面形态判别关系式。通过本文实验结果和前人实验结果对趋势线进行拟合,求得其判别系数,判别式能够较好地划分淤积型岸滩、侵蚀型岸滩及过渡型岸滩三种岸滩形态。     

Wave characteristic and morphologic effects on the onshore hydrodynamic response of tsunamis

While the destruction caused by a tsunami can vary significantly owing to near- and onshore controls, we have only a limited quantitative understanding of how different local parameters influence the onshore response of tsunamis. Here, a numerical model based on the non-linear shallow water equations is first shown to agree well with analytical expressions developed for periodic long waves inundating over planar slopes. More than 13,000 simulations are then conducted to examine the effects variations in the wave characteristics, bed slopes, and bottom roughness have on maximum tsunami run-up and water velocity at the still water shoreline. While deviations from periodic waves and planar slopes affect the onshore dynamics, the details of these effects depend on a combination of factors. In general, the effects differ for breaking and non-breaking waves, and are related to the relative shift of the waves along the breaking–non-breaking wave continuum. Variations that shift waves toward increased breaking, such as steeper wave fronts, tend to increase the onshore impact of non-breaking waves, but decrease the impact of already breaking waves. The onshore impact of a tsunami composed of multiple waves can be different from that of a single wave tsunami, with the largest difference occurring on long, shallow onshore topographies. These results demonstrate that the onshore response of a tsunami is complex, and that using analytical expressions derived from simplified conditions may not always be appropriate.     

A wave-resolving model for nearshore suspended sediment transport

This paper presents a wave-resolving sediment transport model, which is capable of simulating sediment suspension in the field-scale surf zone. The surf zone hydrodynamics is modeled by the non-hydrostatic model NHWAVE (Ma et al., 2012). The turbulent flow and suspended sediment are simulated in a coupled manner. Three effects of suspended sediment on turbulent flow field are considered: (1) baroclinic forcing effect; (2) turbulence damping effect and (3) bottom boundary layer effect. Through the validation with the laboratory measurements of suspended sediment under nonbreaking skewed waves and surfzone breaking waves, we demonstrate that the model can reasonably predict wave-averaged sediment profiles. The model is then utilized to simulate a rip current field experiment (RCEX) and nearshore suspended sediment transport. The offshore sediment transport by rip currents is captured by the model. The effects of suspended sediment on self-suspension are also investigated. The turbulence damping and bottom boundary layer effects are significant on sediment suspension. The suspended sediment creates a stably stratified water column, damping fluid turbulence and reducing turbulent diffusivity. The suspension of sediment also produces a stably stratified bottom boundary layer. Thus, the drag coefficient and bottom shear stress are reduced, causing less sediment pickup from the bottom. The cross-shore suspended sediment flux is analyzed as well. The mean Eulerian suspended sediment flux is shoreward outside the surf zone, while it is seaward in the surf zone.     

破碎波群的显著特征指标

群发性是风浪破碎的显著特征,最近的研究表明风浪破碎研究应该基于波群而不是单个波。本文探讨破碎波群区别于非破碎波群的显著特征指标。依据一系列风浪破碎实验数据,采用多种判据与实验现场目测的破碎标记信号相结合的原则划分破碎波群与非破碎波群,考查波群特征量、单个波几何特征量、局地破碎判据指标、波包络几何特征量以及波群能量结构特征量等5大类28个指标在破碎波群与非破碎波群上的分布差异。结果表明:波陡、峰前波陡、瞬时波面斜率、运动学判据指标和动力学判据指标等在破碎非破碎波群上的分布几乎没有交叠;后两者尤为理想,分布明显分离,是破碎波群区别于非破碎波群的显著指标;而其它各指标在破碎波群非破碎波群上的分布都有不同程度的交叠,不能单独依据它们区分破碎波群与非破碎波群。     

Process-based model for nearshore hydrodynamics, sediment transport and morphological evolution in the surf and swash zones

Hydrodynamics and sediment transport in the nearshore zone were modeled numerically taking into account turbulent unsteady flow. The flow field was computed using the Reynolds Averaged Navier–Stokes equations with a k–ε turbulence closure model, while the free surface was tracked using the Volume-Of-Fluid technique. This hydrodynamical model was supplemented with a cross-shore sediment transport formula to calculate profile changes and sediment transport in the surf and swash zones. Based on the numerical solutions, flow characteristics and the effects of breaking waves on sediment transport were studied. The main characteristic of breaking waves, i.e. the instantaneous sediment transport rate, was investigated numerically, as was the spatial distribution of time-averaged sediment transport rates for different grain sizes. The analysis included an evaluation of different values of the wave friction factor and an empirical constant characterizing the uprush and backwash. It was found that the uprush induces a larger instantaneous transport rate than the backwash, indicating that the uprush is more important for sediment transport than the backwash. The results of the present model are in reasonable agreement with other numerical and physical models of nearshore hydrodynamics. The model was found to predict well cross-shore sediment transport and thus it provides a tool for predicting beach morphology change.     

Database of full-scale laboratory experiments on wave-driven sand transport processes

A new database of laboratory experiments involving sand transport processes over horizontal, mobile sand beds under full-scale non-breaking wave and non-breaking wave-plus-current conditions is described. The database contains details of the flow and bed conditions, information on which quantities were measured and the value of the measured net sand transport rate for 298 experiments conducted in 7 large-scale laboratory facilities. Analysis of the coverage of the experiments and the measured net sand transport rates identified the following gaps in the range of test conditions and/or the type of measurements: (i) graded sand experiments, (ii) wave-plus-current experiments and (iii) intra-wave velocity and concentration measurements in the ripple regime. Furthermore, it highlights two areas requiring further research: (i) the differences in sand transport processes and sand transport rates between real waves and tunnel flows with nominally similar near-bed oscillatory flow conditions and (ii) the effects of acceleration skewness on transport rates. The database is a useful resource for the development and validation of sand transport models for coastal applications.     

Modeling wave�Ccurrent bottom boundary layers beneath shoaling and breaking waves

The boundary layer characteristics beneath waves transforming on a natural beach are affected by both waves and wave-induced currents, and their predictability is more difficult and challenging than for those observed over a seabed of uniform depth. In this research, a first-order boundary layer model is developed to investigate the characteristics of bottom boundary layers in a wave–current coexisting environment beneath shoaling and breaking waves. The main difference between the present modeling approach and previous methods is in the mathematical formulation for the mean horizontal pressure gradient term in the governing equations for the cross-shore wave-induced currents. This term is obtained from the wave-averaged momentum equation, and its magnitude depends on the balance between the wave excess momentum flux gradient and the hydrostatic pressure gradient due to spatial variations in the wave field of propagating waves and mean water level fluctuations. A turbulence closure scheme is used with a modified low Reynolds number k-ε model. The model was validated with two published experimental datasets for normally incident shoaling and breaking waves over a sloping seabed. For shoaling waves, model results agree well with data for the instantaneous velocity profiles, oscillatory wave amplitudes, and mean velocity profiles. For breaking waves, a good agreement is obtained between model and data for the vertical distribution of mean shear stress. In particular, the model reproduced the local onshore mean flow near the bottom beneath shoaling waves, and the vertically decreasing pattern of mean shear stress beneath breaking waves. These successful demonstrations for wave–current bottom boundary layers are attributed to a novel formulation of the mean pressure gradient incorporated in the present model. The proposed new formulation plays an important role in modeling the boundary layer characteristics beneath shoaling and breaking waves, and ensuring that the present model is applicable to nearshore sediment transport and morphology evolution.     

Laboratory study of wave and turbulence characteristics in narrow-band irregular breaking waves

Wave elevations and water particle velocities were measured in a laboratory surf zone created by the breaking of a narrow-band irregular wave train on a 1/35 plane slope. The incident waves form wave groups that are strongly modulated. It is found that the waves that break close to the shoreline generally have larger wave-height-to-water-depth ratios before breaking than the waves that break farther offshore. After breaking, the wave-height-to-water-depth ratio for the individual waves approaches a constant value in the inner surf zone, while the standard deviation of the wave period increases as the still water depth decreases. In the outer surf zone, the distribution of the period-averaged turbulent kinetic energy is closely correlated to the initial wave heights, and has a wider variation for narrow-band waves than for broad-band waves. In the inner surf zone, the distribution of the period-averaged turbulent kinetic energy is similar for narrow-band waves and broad-band waves. It is found that the wave elevation and turbulent kinetic energy time histories for the individual waves in a wave group are qualitatively similar to those found in a spilling regular wave. The time-averaged transport of turbulent kinetic energy by the ensemble-averaged velocity and turbulence velocity under the irregular breaking waves are also consistent with the measurements obtained in regular breaking waves. The experimental results indicate that the shape of the incident wave spectrum has a significant effect on the temporal and spatial variability of wave breaking and the distribution of turbulent kinetic energy in the outer surf zone. In the inner surf zone, however, the distribution of turbulent kinetic energy is relatively insensitive to the shape of the incident wave spectrum, and the important parameters are the significant wave height and period of the incident waves, and the beach slope.     

粤东后江湾冲流带滩面高频振动及动力作用分析

利用涌浪影响下短时段内的冲流带滩面高频高程数据和碎波带波流资料,在奇异谱分析(SSA)的基础上,以比研究了不同形态滩面的冲淤变化趋势、趋势分布形状、冲淤变化周期和冲淤变化强度,以及同一条剖面不同桩点间各因素间的变化关系;用交叉谱方法探索了每分钟滩面高频冲淤变化与碎波带长重力波间的作用关系.分析结果表明,滩角韵律地形引起的冲流分流作用促进了滩脊向滩谷的泥沙转运,冲流带滩面存在明显的长重力波频段的周期性冲淤振动,滩面冲淤振动强度由滩面下部向上部递减,碎波带长重力波对滩面高频冲淤变化起重要作用.     

Bailard's sediment transport formulation in shelf sea conditions: comparison with observations using a clustering technique

A previously published wave-averaged version of Bailard's sediment transport formulation, intended for use in a numerical model of shelf sand transport, is compared against available field observations from literature. The objective was to test the performance of the transport relation over the wide range of hydrodynamical conditions that can occur at sea. A modified data analysis method was used to assess the reliability of the field observations. The modification consists of a method to cluster the data into classes to enable statistical analysis. The sediment transport formulation is part of the classification method. The method is in principle also suitable to reduce the size of data sets of non-cohesive sediment transport obtained with modern electronic equipment. The results show that the quality of the published field observations is fair, and that the wave-averaged Bailard formulation performs well for low and medium transport regimes in both currents and waves. For those conditions, it yields a slight overprediction of the transports, and a nearly uniform behaviour as a function of the conditions. The formulation underestimates transport rates for very high flow velocities in absence of waves, which is in agreement with earlier findings. The present version of Bailard's wave averaged sediment transport formulation is suitable for computing the local transport rates of fine to coarse sand on continental shelves in conditions ranging from small currents to moderate currents combined with non-breaking waves.