Comparative study on adsorption of chromium(VI) from industrial wastewater onto nature-derived adsorbents (brown coal and zeolite)

The removal of hexavalent chromium from wastewater streams has received an considerable attention in recent years, since it can cause harmful effects on the environment. Several approaches, including adsorption, are recognized to tackle this problem, but unfortunately most of these processes are impressed with practical conditions of the experiments. The main objective of this study was to recognize applicable conditions for Cr(VI) removal from an industrial drainage using nature-derived adsorbents (brown coal and modified zeolite) and to make the process more adaptive by using adsorbents conjointly. Batch experiments were carried out by agitating Cr(VI) stock solution with adsorbents at room temperature. The influence of main operating parameters was explored, and the best proportion of the adsorbents was determined. Maximum sorption of Cr(VI) onto brown coal was observed at pH = 4 by adding 60 g L^?1 adsorbent to contaminated solution. In case of using zeolite, the modification process was required, and the pH indicated a weak influence in a wide range (2–8). Optimum dosage of modified zeolite for Cr(VI) removal was 10 g L^?1. The hybrid application of adsorbents with the mass ratio of brown coal/modified zeolite at (3:1) was capable of removing more than 99% of Cr(VI) from contaminated wastewater in the natural pH range of the wastewater. The adsorption of Cr(VI) by brown coal and modified zeolite followed Langmuir and Freundlich isotherm models, respectively. Sorption of Cr(VI) onto both brown coal and modified zeolite fitted well to pseudo-second-order rate reaction.     

A novel adsorbent for heavy metal remediation in aqueous environments

The objective of this study was to investigate the possibility of using maize tassel as an alternative adsorbent for the removal of chromium (VI) and cadmium (II) ions from aqueous solutions. The effect of pH, solution temperature, contact time, initial metal ion concentration and adsorbent dose on the adsorption of chromium (VI) and cadmium (II) by tassel was investigated using batch methods. Adsorption for both chromium (VI) and cadmium (II) was found to be highly pH dependent compared to the other parameters investigated. Obtained results gave an adsorption capacity of 79.1 % for chromium (VI) at pH 2, exposure time of 1h at 25 °C. Maximum capacity of cadmium of 88 % was obtained in the pH range of 5-6 at 25 °C after exposure time of 1 h. The adsorption capacities of tassel for both chromium (VI) and cadmium (II) were found to be comparable to those of other commercial adsorbents currently in use for the removal of heavy metals from aqueous wastes. These results have demonstrated the immense potential of maize tassel as an alternative adsorbent for toxic metal ions remediation in polluted water and wastewater.     

Effective removal of zinc from an aqueous solution using Turkish leonardite–clinoptilolite mixture as a sorbent

In this study, the feasibility of using a low-cost adsorbent mixture composed of leonardite (L) and clinoptilolite (C) was evaluated by batch adsorption method using different parameters such as mixing ratio, contact time, pH, temperature, and adsorbent amount for the removal of Zn (II) ions from an aqueous solution. The adsorbents were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and Raman spectroscopy. Additionally, leonardite–clinoptilolite mixture was analyzed by scanning electron microscopy coupled with energy dispersive X-ray. The Zn (II) adsorption along with an unprecedented adsorption capacity of 454.55 mg g^?1 for unmodified natural sorbents was obtained by mixing leonardite and clinoptilolite (LC) without any pretreatment at a ratio of 3:1, using 0.1 g of sorbent at a pH 6, for 2 h of contact time. The experimental data showed a good fit for the Langmuir isotherm model. The thermodynamic parameters revealed that the present adsorption process was spontaneous and exothermic in nature (25–50 °C). The kinetic results of the adsorption showed that the Zn (II) adsorption onto the LC follows pseudo-second-order model. The resultant LC mixture has an excellent adsorption capacity of a Zn (II) aqueous solution, and data obtained may form the basis for utilization of LC as an unpretreated low-cost adsorbent for treatment of metalliferous industrial wastewater.     

Insight into adsorption equilibrium,kinetics and thermodynamics of lead onto alluvial soil

In the present study, adsorption of lead (II) ions from aqueous solution by alluvial soil of Bhagirathi River was investigated under batch mode. The influence of solution pH, sorbent dose, initial lead (II) concentration, contact time, stirring rate and temperature on the removal process were investigated. The lead adsorption was favored with maximum adsorption at pH 6.0. Sorption equilibrium time was observed in 60 min. The equilibrium adsorption data were analyzed by the Freundlich, Langmuir, Dubinin–Radushkevich and Temkin adsorption isotherm models. The kinetics of lead (II) ion was discussed by pseudo first-order, pseudo second-order, intra-particle diffusion, and surface mass transfer models. It was shown that the adsorption of lead ions could be described by the pseudo second-order kinetic model. The activation energy of the adsorption process (E _a) was found to be ?38.33 kJ mol^?1 using the Arrhenius equation, indicating exothermic nature of lead adsorption onto alluvial soil. Thermodynamic parameters, such as Gibbs free energy (?G ⁰), the enthalpy (?H ⁰), and the entropy change of sorption (?S ⁰) have also been evaluated and it has been found that the adsorption process was spontaneous, feasible, and exothermic in nature. The results indicated that alluvial soil of Bhagirathi River can be used as an effective and low cost adsorbent to remove lead ions from aqueous solutions.     

Removal of ibuprofen from aqueous solution by functionalized strong nano-clay composite adsorbent: kinetic and equilibrium isotherm studies

The functionalized nano-clay composite adsorbent was prepared, and its properties were characterized using FT-IR, XRD and SEM techniques. The synthesized nano-clay composite was studied with regard to its capacity to remove ibuprofen under different adsorption conditions such as varying pH levels (5–9), initial ibuprofen concentrations (3, 5 and 10 mg L^?1), contact time, and the amount of adsorbent (0.125, 0.25, 0.5 and 1 g). In order to evaluate the nanocomposite adsorption capacity, the adsorption results were assessed using nine isotherm models. The results showed that the optimum adsorption pH was 6 and that an increase or decrease in the pH reduced the adsorption capacity. The adsorption process was fast and reached equilibrium after 120 min. The maximum efficacy of ibuprofen removal was approximately 95.2%, with 1 g of adsorbent, 10 mg L^?1 initial concentration of ibuprofen, 120 min contact time and pH = 6. The optimal adsorption isotherm models were the Freundlich, Fritz–Schlunder, Redlich–Peterson, Radke–Prausnitz, Sip, Toth and Khan models. In addition, four adsorption kinetic models were employed for adsorption system evaluation under a variety of experimental conditions. The kinetic data illustrated that the process is very fast, and the reaction followed the Elovich kinetic model. Therefore, this nano-clay composite can be used as an effective adsorbent for the removal of ibuprofen from aqueous solutions, such as water and wastewater.     

Adsorption of lead, zinc and cadmium ions from contaminated water onto Peganum harmala seeds as biosorbent

Peganum harmala seeds were assessed as biosorbent for removing Pb²⁺, Zn²⁺and Cd²⁺ ions from aqueous solutions. The effects of various parameters such as the aqueous solution pH, the contact time, the initial metal concentration and the amount of adsorbent in the process were investigated. The adsorption efficiencies increased with pH. It was found that about 95 % of lead, 75 % of zinc and 90 % of cadmium ions could be removed from 45 ml of aqueous solution containing 20 mg l^?1 of each cation with 2 g of adsorbent at pH 4.5 after 15 min. The quantitative desorption of cadmium from adsorbent surface was achieved using 10 ml of a 0.5 M nitric acid solution. This condition was attained for lead and zinc ions with 10 ml of 1 M hydrochloric acid solution. Kinetic investigation of the process was performed by considering a pseudo-second-order model. This model predicts the chemisorption mechanism of the process. Langmuir, Freundlich, Temkin and Dubinin–Radushkevich models were tested for describing the equilibrium data. It was found that the Freundlich model describes the experimental data resulting from the adsorption of lead ions. However for cadmium and zinc ions, the adsorption equilibria were interpreted with the Langmuir model.     

Uptake of Indosol Dark-blue GL dye from aqueous solution by water hyacinth roots powder: adsorption and desorption study

Adsorption characteristics of water hyacinth roots powder for the removal of Indosol Dark-blue GL dye were investigated in batch mode. Operating variables, such as initial solution pH, presence of detergent, adsorbent dosage, initial concentration and contact time, were studied. The results showed that the adsorption of dye increased with increasing the initial concentration and contact time. The adsorption is highly pH dependent and adsorption capacity increased with decrease in pH. Kinetic study revealed that the uptake of Indosol Dark-blue GL was very rapid within the first 15 min and equilibrium time was independent of initial concentration. Batch equilibrium experiments were carried out at different pH and found that equilibrium data fitted well to Langmuir isotherm model. The maximum sorption capacity of the adsorbent was found as 86 mg g^?1 at pH 3 which reduced to 64 mg g^?1 at pH 5. The presence of detergent reduced the sorption capacity of the adsorbent significantly. Using equilibrium and kinetic data, the forward and backward rate constants were determined from the unified approach model. Desorption study revealed that the dye can be recovered by swing the pH from low to high.     

Applications on agricultural and forest waste adsorbents for the removal of lead (II) from contaminated waters

At present, there is growing interest in using low cost, commercially available materials for the adsorption of heavy metals. The major advantages of adsorption technologies are its effectiveness in reducing the concentration of heavy metal ions to very low levels and the use of inexpensive adsorbent materials. In this review, agricultural and forest waste adsorbents were used to remove Pb²⁺ ions in wastewater treatment, and their technical feasibilities were reviewed in studies mainly from 2000 to 2010. They all were compared with each other by metal binding capacities, metal removal performances, sorbent dose, optimum pH, temperature, initial concentration and contact time. Although commercial activated carbon is widely used in wastewater treatment applications, it has high costs. The use of agricultural by-products as adsorbent material to purify heavy metal contaminated water has become increasingly popular through the past decade because they are less expensive, biodegradable, abundant and efficient. Instead of activated carbon, this study was focused on the inexpensive materials such as agricultural and forest waste. It was shown that these alternative adsorbents had sufficient binding capacity to remove Pb²⁺ ions from wastewater.     

Adsorptive removal of Cu(II) and Pb(II) onto mixed-waste activated carbon: kinetic,thermodynamic, and competitive studies and application to real wastewater samples

This work aimed to investigate the adsorption characteristics, both kinetically and thermodynamically, of Cu(II) and Pb(II) removal from aqueous solutions onto mixed-waste activated carbon, as well as to study the competitive behavior found in mixed heavy metal solution systems. This study shows that activated carbon prepared from mixed waste is an effective adsorbent for the removal of Cu(II) and Pb(II) from aqueous solutions, with the aim of detoxifying industrial effluents before their safe disposal onto water surfaces. The adsorption process was characterized in terms of kinetic and thermodynamic studies. In addition, the influence of presence of Cu(II) and Pb(II) in a competitive system was investigated. The results showed that the maximum adsorption capacities were gained at a pH of 6 with a contact time of 180 min, a metal solution concentration of 300 ppm, and an adsorbent dose of 0.3 g/L. The adsorption process was found to follow a pseudo-first-order kinetic model. Thermodynamic parameters such as ΔG ^o, ΔH ^o, and ΔS ^o showed that the sorption process was spontaneous and endothermic in nature. A competitive study demonstrated the applicability of mixed-waste activated carbon to adsorb Cu(II) and Pb(II) from a solution of mixed metals. In addition, the adsorption capacity was found to be as effective as other adsorbents reported in the literature. The developed adsorptive removal procedure was applied for treatment of real wastewater samples and showed high removal efficiency.     

Potentiality of open burnt clay as an adsorbent for the removal of Congo red from aqueous solution

Open burnt clay was studied as a potential adsorbent for the adsorption of Congo red (a reactive dye) from aqueous solution. The effect of contact time, pH, adsorbent dosage and temperature were studied. It was observed that the amount of Congo red retained increase with decreasing pH and increasing initial concentration. Removal percentage at pH 2 and 3 are almost same. The adsorption capacity of regenerated burnt clay was showed more than 98 % recovery of the adsorption efficiency of initial virgin adsorbent. The equilibrium data were described well by both Langmuir and Freundlich isotherm model. The adsorption capacity of some natural adsorbents, namely rice husk, wood charcoal, tea waste etc. were also investigated and compared with that of open burnt clay.     

Application of dried plant biomass as novel low-cost adsorbent for removal of cadmium from aqueous solution

Heavy metals are a threat to human health and ecosystem. These days, great deal of attention is being given to green technologies for purification of water contaminated with heavy metal ions. Biosorption is one among such emerging technologies, which utilizes naturally occurring waste materials to sequester heavy metals from wastewater. Cadmium has hazardous impact on living beings; therefore, its removal through green and economical process is an important task. The aim of the present study was to utilize the locally available Portulaca oleracea plant biomass as an adsorbent for cadmium removal from aqueous solution. The biomass was obtained after drying and grinding the portulaca leaves and stem. No chemical treatment was done on the adsorbent so that it remained green in a true sense. Batch experiments were performed at room temperature. The critical parameters studied were effects of pH, contact time, initial metal ion concentration and adsorbent dose on the adsorption of cadmium. The maximum adsorption was found to be 72 %. The kinetic data were found to best fit the pseudo-second-order equation. High adsorption rates were obtained in the initial 45 min, and adsorption equilibrium was then gradually achieved in about 100 min. Adsorption increased with increase in pH for a range 2 and 6. The equilibrium adsorption results closely followed both the Langmuir and Freundlich isotherms. The values of constants were calculated from isotherms. Results indicated that portulaca plant biomass could be developed as a potential material to be used in green water treatment devices for removal of metal ions.     

Adsorption of methylene blue and crystal violet on low-cost adsorbent: waste fruits of <Emphasis Type="Italic">Rapanea ferruginea</Emphasis> (ethanol-treated and H<Subscript>2</Subscript>SO<Subscript>4</Subscript>-treated)

This study assesses the ability of two low-cost adsorbents made from waste of Rapanea ferruginea treated with ethanol (WRf) and its H₂SO₄-treated analog (WRf/H₂SO₄) for the removal of two cationic dyes methylene blue (MB) and crystal violet (CV) from aqueous solutions. The adsorbent was characterized by scanning electron microscopy, Fourier transform infrared spectrometry, thermogravimetric analysis, point of zero charge (pH_pzc), specific surface, and functional groups. The adsorption of dye onto the adsorbents was studied as a function of pH solution (2–12), contact time (up to 120 min) and initial concentration (20–120 mg/L), and temperature (25, 35, and 55 °C). The influence of these parameters on adsorption capacity was studied using the batch process. The response surface methodology (RSM) was used in the experimental design, modeling of the process, and optimizing of the variables and was optimized by the response involving Box–Behnken factorial design (15 runs). The results show that the data correlated well with the Sips isotherm. The maximum adsorption capacities of MB and CV onto WRf were found to be 69 and 106 mg/g, and onto WRf/H₂SO₄, the adsorption capacities were 33 and 125 mg/g, respectively. The kinetic data revealed that adsorption of cationic dyes onto the adsorbents closely follows the pseudo-second-order kinetic model. Regression analysis showed good fit of the experimental data to the second-order polynomial model, with coefficient of determination (R²) values for MB (R²?=?0.9685) and MB (R²?=?0.9832) for WRf and CV (R²?=?0.9685) and CV (R²?=?0.9832) for WRf/H₂SO₄ indicated that regression analysis is able to give a good prediction of response for the adsorption process in the range studied. The results revealed that waste from R. ferruginea is potentially an efficient and low-cost adsorbent for adsorption of MB and CV.     

Fluoride contamination of groundwater in parts of eastern India and a preliminary experimental study of fluoride adsorption by natural haematite iron ore and synthetic magnetite

Incidence of high fluoride (F^?) in groundwater (>1.5 mg/L) in two tribal belts of eastern India, one around Chukru in the Palamau district of Jharkhand and the other around Karlakot in the Nuapada district of Odisha, has been studied. The maximum concentration of F^? in groundwater from dug wells and tube wells is 10.30 mg/L in Chukru and 4.62 mg/L in Karlakot. The groundwaters are mildly alkaline with pH ranges of 7.52–8.22 and 7.33–8.20 in Chukru and Karlakot, respectively. The F^? concentration is positively correlated with pH, electrical conductivity and SO₄ ^2? in both areas. The high F^? in groundwater resulted mainly from dissolution of biotite and fluorapatite in quartzofeldspathic gneiss. The ionic dominance pattern (in meq/L) is mostly in the order Ca²⁺ > Na⁺ > Mg²⁺ > K⁺ among cations and HCO₃ ^? > SO₄ ^2? > < Cl^? > F^? among anions in the Karlakot groundwater. Preliminary adsorption experiments were conducted on natural haematite iron ore and synthetic magnetite to evaluate their potential for F^? removal from water. Effects of different parameters such as contact time, pH, adsorbent dose and initial F^? concentration on the adsorption capacity of these materials were investigated. Strong dependence of F^? removal on pH was observed for both the adsorbents. With natural haematite iron ore, the maximum F^? removal of 66 % occurred at an initial pH of 3.2 for a solution with F^? concentration of 3 mg/L, adsorbent dose of 7 g/L and overnight contact time. The haematite iron ore was observed to increase the pH of the F^? solution. Adsorption equilibrium was not achieved with this adsorbent even after a contact time of 45.2 h. In the case of synthetic magnetite, 84 % F^? removal was achieved after 2 min of contact time for a solution with F^? concentration of 6 mg/L, adsorbent dose of 10 g/L and initial pH of 7. The results indicate high potential of both natural haematite iron ore and synthetic magnetite as adsorbents of F^? in water.     

Characterization and adsorption of disperse dyes from wastewater onto cenospheres activated carbon composites

In the present research, coal fly ash, a waste by-product of thermal power plant, has been segregated to obtain hollow and spherical cenospheres which combined with activated carbon in different ratio for effectual remediation of wastewater. Fabricated cenospheres activated carbon (CNAC) composites were characterized by ATR-FTIR, SEM, XRD, BET and CILAS for functionality, surface modification, crystallinity, surface area, pore volume, pore size and particle size analysis, respectively. Batch adsorption has been applied to appraised maximum removal of Disperse Orange 25 (DO) and Disperse Blue 79:1 (DB) dyes at varying solution pH 2 to 12, adsorbent dose 0.1 g cenospheres + 0.1 g AC to 1.0 g cenospheres + 1.0 g AC, dye concentration 10 to 100 mg/L, agitation speed 80 to 240 rpm and contact time 5 to 300 min at three different temperatures (25, 35 and 45 °C). The maximum percentage removal was found to be 79 and 76% for DO and DB dyes, respectively, at optimized condition. Langmuir isotherm showed good interaction with adsorption data, and the obtained maximum equilibrium adsorption capacity was found to be 90.91 mg/g for DO and 83.33 mg/g for DB at 45 °C. Eventually, the negative ?G° (? 7.513 for DO and ? 7.767 for DB) has suggested the feasibility of dyes adsorption on CNAC composites.     

Nettle ash as a low cost adsorbent for the removal of nickel and cadmium from wastewater

This study was focused on nettle ash as an alternative adsorbent for the removal of nickel (II) and cadmium (II) from wastewater. Batch experiments were conducted to determine the factors affecting adsorption of nickel (II) and cadmium (II). The adsorption process is affected by various parameters such as contact time, solution pH and adsorbent dose. The optimum pH required for maximum adsorption was found to be 6. The experimental data were tested using Langmuir, Freundlich and Tempkin equations. The data were fitted well to the Langmuir isotherm with monolayer adsorption capacity of 192.3 and 142.8 mg/g for nickel and cadmium, respectively. The adsorption kinetics were best described by the pseudo second order model. The cost of removal is expected to be quite low, as the adsorbent is cheap and easily available in large quantities. The present study showed that nettle ash was capable of removing nickel and cadmium ions from aqueous solution.     

Empirical and mechanistic evaluation of sodium exchange isotherms on natural mineral and organic adsorbents and organically functionalized nanoparticles

This study was conducted to evaluate the efficiency of low-cost adsorbents including bentonite, kaolinite and zeolite saturated with calcium and potassium, potato and wheat residues, and three metal oxide nanoparticles functionalized with an acidic extract of potato residues in improving the quality of sodic waters. The optimization of factors such as pH, contact time, and adsorbent dosage was investigated using a solution containing sodium, calcium, magnesium, and potassium. The optimal pH and contact time were 7.0 and 24 h, respectively. The optimal dosage for using functionalized nanoparticles was 0.1 g and for using other adsorbents was 1.0 g. The sodium exchange isotherms were conducted in binary sodium–calcium and sodium–potassium and quaternary sodium–calcium–magnesium–potassium systems. Zeolite saturated with potassium was the most effective adsorbent in removing sodium from aqueous solutions with an average removal efficiency of 69.2 and 66.5 % in binary and quaternary systems, respectively. Freundlich and Langmuir equations fitted well to experimental data in both binary and quaternary systems. Cation selectivity coefficients calculated based on the Gaines–Thomas convention varied with changing pH and adsorbent dosage. Graphical and statistical evaluations confirmed that the mechanistic cation exchange model using average Gaines–Thomas selectivity coefficients in geochemical PHREEQC program was able to successfully simulate the sodium exchange on different adsorbents in both systems. The Gaines–Thomas selectivity coefficient values greater than unity and as a consequence, the negative values of the Gibbs free energy change of adsorption indicated that sodium exchange reactions in the presence of different adsorbents used is this study were exergonic and spontaneous.     

Application of Chitin and Zeolite adsorbents for treatment of low level radioactive liquid wastes

Two types of Shrimp Chitin derivatives and two types of Iranian natural Zeolite derivatives (Firuzkooh Clinoptiliolite) were studied for adsorption and treatment of low-level radioactive liquid waste (LLW). Chitin with lowers than 10% and Chtiosan with higher than 90% deacetylation factor were selected as natural organic adsorbents. Natural Cliniptilolite of Firuzkooh area and Na form derivatives of it were selected as natural inorganic adsorbents. The static and dynamic ion exchange experimental results show that the adadsorption efficiency depend on particle size, PH, adsorbent type, deacetylation factor (in Chitin adsorbents) and cation type. The best Cs adsorption occurred in Na form Clinoptilolite. Nevertheless Chitin derivatives, particularly Chitosan, are more efficient than Zeolite adsorbents for removing of radionuclides such as ¹³⁷Cs, ⁵⁴Mn, ⁹⁰Sr and ⁶⁰Co. Adsorption performance was discussed and compared with each other.     

Removal of lead (II) from synthetic and batteries wastewater using agricultural residues in batch/column mode

The present article explores the ability of five different combinations of two adsorbents (Arachis hypogea shell powder and Eucalyptus cameldulensis saw dust) to remove Pb(II) from synthetic and lead acid batteries wastewater through batch and column mode. The effects of solution pH, adsorbent dose, initial Pb(II) concentration and contact time were investigated with synthetic solutions in batch mode. The Fourier transform infrared spectroscopy study revealed that carboxyl and hydroxyl functional groups were mostly responsible for the removal of Pb(II) ions from test solutions. The kinetic data were found to follow pseudo-second-order model with correlation coefficient of 0.99. Among Freundlich and Langmuir adsorption models, the Langmuir model provided the best fit to the equilibrium data with maximum adsorption capacity of 270.2 mg g^?1. Column studies were carried out using lead battery wastewater at different flow rates and bed depths. Two kinetic models, viz. Thomas and Bed depth service time model, were applied to predict the breakthrough curves and breakthrough service time. The Pb(II) uptake capacity (q _e = 540.41 mg g^?1) was obtained using bed depth of 35 cm and a flow rate of 1.0 mL min^?1 at 6.0 pH. The results from this study showed that adsorption capacity of agricultural residues in different combinations is much better than reported by other authors, authenticating that the prepared biosorbents have potential in remediation of Pb-contaminated waters.     

High efficacy on diclofenac removal by activated carbon produced from potato peel waste

In the present study, a novel porous carbon obtained by K₂CO₃ activation of potato peel waste under optimized conditions was applied for the first time as liquid-phase adsorbent of sodium diclofenac in parallel with a commercial activated carbon. The biomass-activated carbon presented an apparent surface area of 866 m² g^?1 and well-developed microporous structure with a large amount of ultramicropores. The obtained carbon presented leaching and ecotoxicological properties compatible with its safe application to aqueous medium. Kinetic data of laboratory-made and commercial sample were best fitted by the pseudo-second-order model. The commercial carbon presented higher uptake of diclofenac, but the biomass carbon presented the higher adsorption rate which was associated with its higher hydrophilic nature which favoured external mass transfer. Both adsorbents presented adsorption isotherms that were best fitted by Langmuir model. The biomass carbon and the commercial carbon presented adsorption monolayer capacities of 69 and 146 mg g^?1, and Langmuir constants of 0.38 and 1.02 L mg^?1, respectively. The better performance of the commercial sample was related to its slightly higher micropore volume, but the most remarkable effect was the competition of water molecules in the biomass carbon.     

Removal of lead from aqueous solution using low cost abundantly available adsorbents

The removal of poisonous Pb (II) from wastewater by different low-cost abundant adsorbents was investigated. Rice husks, maize cobs and sawdust, were used at different adsorbent/metal ion ratios. The influence of pH, contact time, metal concentration, adsorbent concentration on the selectivity and sensitivity of the removal process was investigated. The adsorption efficiencies were found to be pH dependent, increasing by increasing the solution pH in the range from 2.5 to 6.5. The equilibrium time was attained after 120 min and the maximum removal percentage was achieved at an adsorbent loading weight of 1.5 gm. The equilibrium adsorption capacity of adsorbents used for lead were measured and extrapolated using linear Freundlich, Langmuir and Temkin isotherms and the experimental data were found to fit the Temkin isotherm model.