虹口八角庙-深溪沟炭质泥岩同震断层泥的X射线衍射分析结果

5.12汶川地震同震地表破裂带在虹口八角-深溪沟一带主要出露于三叠系须家河组的炭质泥岩中,同震断层泥在颜色、结构上与老断层泥和围岩类似。通过开挖探槽,系统采样,采用粉晶X射线衍射定量分析方法,研究了同震地表破裂带的围岩、断层角砾岩、老断层泥和新断层泥的矿物成分特征。同震断层泥的主要成分为石英和黏土矿物,含微量长石和白云石;断层泥的显著特征为高黏土矿物含量,从同震断层泥、老断层泥、角砾岩到围岩黏土矿物含量依次降低,黏土矿物以伊利石和伊蒙混层为主,含微量绿泥石和高岭石,矿物组成明显比地表破裂带北段同震断层泥简单。不同颜色的同震断层泥成分略有不同,黑色断层泥中伊利石含量明显高于白色断层泥;老断层泥中含有方解石和白云石,而同震断层泥不含方解石,只含微量白云石。同震断层泥中伊蒙混层高含量表明,在本次地震错动中有富含K的流体参与。     

断层泥的再生显微结构特征及其地震地质意义

三轴剪切摩擦实验后的断层泥与天然断层泥的再生显微结构特征研究表明，断层泥的显微结构特征与断层滑动方式之间有一定的关系，稳滑使断层泥变形均匀，产生低角度剪切（＜１４°）、布丁构造和颗粒碎裂流动。粘滑使断层泥局部发生强烈变形、高角度剪切（＞１４°）和碎粒出现随机裂纹等。断层泥的再生显微结构特征可用作鉴别古地震的存在     

龙门山断裂带金河磷矿剖面断层泥的低速至高速摩擦性质研究

本文对龙门山断裂带金河磷矿浅钻岩芯中的三种断层泥开展了低速到高速摩擦滑动的实验研究,并对实验变形样品开展了BET比表面积研究.摩擦实验在干燥和孔隙水压条件下开展,速率范围涵盖20 μm·s^-1~1.4 m·s^-1.实验结果显示,三种断层泥在干燥条件下的摩擦性质差别不大,但在孔隙水压条件下,三者的中低速摩擦强度与层状硅酸盐矿物的种类而非总含量紧密相关,蒙脱石和伊利石相比绿泥石更能有效地弱化断层.三种断层泥在孔隙水压条件下存在中低速率域的速度强化,暗示着对断层的加速滑动存在一定的阻碍作用.孔隙水压下,黄绿色和灰绿色断层泥的初始动态弱化非常迅速并伴随断层泥层的瞬时扩容,凹凸体急剧加热导致的局部热压作用可能是造成这种力学行为的物理机制.在经历高速滑动之后,三种断层泥在干、湿条件下的BET比表面积都显著降低,暗示着可能发生了颗粒烧结.中低速域内,孔隙水的存在使得断层泥呈现分散式的剪切变形,BET比表面积的增加因此比干燥条件下更加明显.对表面能的估算表明,颗粒磨碎所消耗的能量至多不超过摩擦力做功的8%,暗示着断层作用中颗粒磨碎所占的能量比例较低.     

Fault rock analysis of the northern part of the Chelungpu Fault and its relation to earthquake faulting of the 1999 Chi-Chi earthquake, Taiwan

Abstract   The 1999 Chi-Chi earthquake in Taiwan ( M _w = 7.6) produced a surface rupture along the north–south-striking Chelungpu thrust fault with pure dip-slip (east side up) and left lateral strike-slip displacements. Near-field strong-motion data for the northern part of the fault illustrate a distinct lack of the high-frequency seismic radiation associated with a large slip (10–15 m) and a rapid slip velocity (2–4 m/s), suggesting a smooth seismic slip associated with low dynamic frictional resistance on the fault. A drillhole was constructed at shallow depths in the possible fault zones of the northern part of the Chelungpu Fault, which may have slipped during the 1999 earthquake. One of the zones consists of a 20-cm-thick, unconsolidated fault breccia with a chaotic texture lacking both discrete slip surfaces (e.g. Riedel shears) and grain crushing. Other possible fault zones are marked by the narrow (less than a few centimeters) gouge zone in which clayey material intrudes into the damaged zone outside of the gouge zone. These characteristic fault rock textures suggest that the slip mechanisms at shallow levels during the earthquake involved either granular flow of initially unconsolidated material or slip localization under elevated pore pressure along the narrow clayey gouge zone. Because both mechanisms lead to low dynamic frictional resistance on the fault, the rapid seismic slip in the deep portions of the fault (i.e. the source region of strong-motion radiation) could have been accommodated by frictionless slip on the shallow portions of the fault. The combination of strong-motion data and fault rock analysis suggests that smooth slip associated with low dynamic friction occurred on both the deep and shallow portions of the fault, resulting in a large slip between the source region and the surface in the northern region.     

FRICTIONAL PROPERTIES OF A NATURAL FAULT GOUGE FROM DRILLED CORES IN THE LONGMENSHAN FAULT ZONE CUTTING GRANITIC ROCK

In this paper, we report friction experiments performed on natural fault gouge samples embedded in granitic rock from drilled core by a project entitled "the Longmenshan Fault Shallow Drilling(LMFD)". Compared with other natural fault gouge, this yellow-greenish gouge(YGG)is dominantly chlorite-rich. The maximum content of chlorite reaches 47%in the YGG. To understand the frictional properties of the YGG sample, experiments were performed at constant confining pressure of 130MPa, with constant pore pressure of 50MPa and at different temperatures from 25℃ to 150℃. The experiments aim to address the frictional behavior of the YGG under shallow, upper crustal pressure, and temperature conditions. Compared with previous studies of natural gouge, our results show that the YGG is stronger and shows a steady state friction coefficient of 0.47~0.51. Comparison with previous studies of natural gouge with similar content of clay minerals indicates a sequence of strengths of different clay minerals:chlorite > illite > smectite. At temperatures up to 150℃ hence depths up to~8km in the Longmenshan region, the YGG shows stable velocity-strengthening behavior at shallow crustal conditions. Combined with the fact of strong direct velocity effect, i.e., (a-b)/a>0.5, faults cutting the present clastic lithology up to~8km depth in the Longmenshan fault zone(LFZ)are likely to offer stable sliding resistance, damping co-seismic rupture propagating from below at not-too-high slip rates. However, as the fault gouge generally has low permeability, co-seismic weakening through thermal pressurization may occur at high slip rates(>0.05m/s), leading to additional hazards.     

X光组构仪在活断层研究中的应用

断层泥矿物的优选方位和组构型式与断层活动的性质有着密切的关系。使用Ｘ射线组构测角仪测试香山－天景山断裂不同区段断层泥伊利石的组构，结果显示，香山－天景山断裂中段断层泥伊利石组构无优选方位，是断层粘滑的结果；东西两段断层泥伊利石组构有一个极密区，是断层左旋剪切蠕动的结果     

Comparative microstructures of natural and experimentally produced clay-bearing fault gouges

Fault rocks formed in phyllosilicate-bearing rocks formed over a wide range of environmental conditions within the Earth's crust are characterised by similar structural and microstructural features. The most striking of these are (a) P foliation, defined by the preferred alignment of phyllosilicates in a plane oblique to the direction of shear and (b) small-scale shear zones either parallel to the shear direction (Y shears) or oblique to the direction of shear but with the opposite sense of obliquity relative to the P foliation (Riedel shears, R₁). The minor shear zones have the same sense of displacement as the host shear zone.The occurrence of these and other structures in clay-rich fault gouges from exceptionally well-exposed fault zones in southeastern Spain is described. The pervasive development of these flow structures throughout large volumes of fault gouge permits fault-displacement vectors to be inferred. For the region studied the movement pictures is relatively simple and is superposed on a complex network of variably oriented fault zones.The naturally produced fault-gouge structures are compared with fault gouges produced experimentally by shearing kaolinite-quartz mixtures between intact blocks over a wide range of experimental conditions. Good correspondence between their respective microstructural features was observed.Finally, attention is drawn to the fact that natural clay-bearing fault gouges are the products of deformation accompanied by very low-grade retrogressive metamorphism, and that part of the micro-structure of these rocks may be ascribed to crystallization under stress. Microstructures are described that are from long-duration experimental runs, (5 months at high temperature and in the presence of water) which go some way towards simulating these effects.     

青藏高原东北缘断层泥的研究

本文对青藏高原东北缘一些主要断裂（包括阿尔金、昌马、毛毛山等断裂）的断层泥首次进行了研究。在对断裂带的内部结构、围岩成分、断层泥的厚度及石英颗粒表面特征等综合分析的基础上对断裂的活动年代、活动方式及断层泥形成的深度进行了讨论。石英颗粒表面上溶蚀程度（颗粒表面的光滑程度、凹凸现象及孔洞发育情况）可划分为６种类型并且每种类型都有相应的年代。根据断裂的粘滑、蠕滑特征，对该区的各活动断裂进行了粘滑段与蠕滑段的划分。用红外光谱与稀土元素的分析结果，算得断层泥形成的深度在地壳１０ｋｍ范围内。     

Grain size and chemical controls on the ductile properties of mostly frictional faults at low-temperature hydrothermal conditions

A conceptually simple process which establishes a steady grain size distribution is envisioned to control the ductile creep properties of fault zones that mainly slip by frictional processes. Fracture during earthquakes and aseismic frictional creep tend to reduce grain size. However, sufficiently small grains tend to dissolve so that larger grains grow at their expense, a process called Ostwald ripening. A dynamic stedy state is reached where grain size reduction by fracture is balanced by grain growth from Ostwald ripening. The ductile creep mechanism within fault zones in hard rock is probably pressure solution where the rate is limited by diffusion along load-bearing grain-grain contacts. The diffusion paths that limit Ostwald repening are to a considerable extent the same as those for pressure solution. Active Ostwald ripening thus implies conditions suitable for ductile creep. An analytic theory allows estimation of the steady-state mean grain size and the viscosity for creep implied by this dynamic steady state from material properties and from the width, shear traction, and long-term slip velocity of the fault zone. Numerical models were formulated to compute the steady state grain size distribution. The results indicate that ductile creep, as suggested in the companion paper, is a plausible mechanism for transiently increasing fluid pressure within mostly sealed fault zones so that frictional failure occurs at relatively low shear tractions, 10 MPa. The relevant material properties are too poorly known, however, for the steady state theory (or its extension to a fault that slips in infrequent large earthquakes) to have much predictive value without additional laboratory experiments and studies of exhumed faults.     

剪切破裂与粘滑——浅源强震发震机制的研究

周口店花岗闪长岩的高温高压三轴实验和理论分析表明,剪切破裂和摩擦滑移具有类似的孕育过程和发生机制。剪切破裂贯通强度就是一种摩擦强度。剪切破裂和摩擦滑移各自都有渐进式和突发式之分。突发式摩擦滑移是已有断层的粘滑滑移。突发式剪切破裂则是完整岩石的初始粘滑滑移。考虑到地壳温度随深度增加,完整岩石剪裂强震要求较高的围压,因此,多数浅源强震的发震方式很可能是已有断层的粘滑     

AN EXPERIMENTAL STUDY ON THE PROCESS OF INTERGRANULAR PRESSURE SOLUTION OF PLAGIOCLASE GOUGE UNDER HIGH TEMPERATURE AND PRESSURE: METHOD AND PRELIMINARY RESULTS

To understand the mechanism of lower-crust earthquake and slow slips, it is necessary to study the frictional properties of mafic rocks and their major rock-forming minerals. Previous studies have performed a series of experimental researches on gabbro, basalt and their major constituents. According to the results of previous experiments, frictional sliding of plagioclase under hydrothermal conditions(100~600℃)shows a property of velocity weakening, and the experimental results show that both the direct rate effect parameter(a)and the healing effect parameter(b)increase with temperature, a typical feature for thermally-activated processes. Velocity weakening means property of a shear band that has a stronger friction healing effect than the direct rate effect in the rate and state friction constitutive framework, and the healing effect(b value)in constitutive relation mainly reflects the increase in contact area with time under hydrothermal conditions, with some minor effect of structural changes. Since the microphysical mechanism of feldspar minerals at the contacts is mainly brittle cataclasis for temperatures below 600℃, the significant frictional healing effect in this case can only be explained by the mechanism of pressure solution. In order to determine if the dissolution process of plagioclase actually occurs on the laboratory time scale, we conducted hydrostatic experiments on plagioclase powder samples under hydrothermal conditions whereby frequent contact switch between particles seen in frictional sliding experiments can be avoided, making the observation on the dissolution sites possible. Experimental temperatures were 400℃ and 500℃, with confining pressure of 90~150MPa, pore pressure of 30MPa, with 2mm initial thickness of fault gouge. The mechanical data show that a creep process occurred in the plagioclase fault gouge in the experimental temperature and pressure range; and the microstructures of the experiment show that precipitation of new grains is prevalent as the product of pressure solution process between plagioclase particles. At the same time, it is observed that the contact points have an appearance similar to fused, fuzzy structure as signatures of dissolution. The results of our experiments provide a definite experimental evidence for the healing mechanism in friction of plagioclase and for the theoretical relation between unstable slip and the pressure solution process. The results of the experiments are summarized as follows: (1)Drainage rate of pore water in plagioclase gouge was high in the first few hours of experiment, but gradually decreases over time for both temperature and pressure series of experiments slowing down to a steady state. This feature indicates that there is a creep process that evolves inside the plagioclase gouge. In the temperature-series experiments, the drainage rate of the pore water in the plagioclase gouge at 400℃ is relatively low than the cases for higher temperatures. Thus, the applied temperature is positively correlated with the creep of plagioclase gouge. (2)Scanning electron microscopy(SEM)observations of the experimentally deformed samples were performed on thin sections cut along the sample axis. Firstly, from the images of microstructure, it was found that the degree of particle fracture became more significant at a higher effective pressure, with smaller pore volume between particles. In the temperature-series experiments it was found that the degree of compaction of plagioclase gouge increased with increasing temperature. Precipitation of plagioclase grains in layered structures was generally observed in high-magnification images, indicating the presence of pressure solution processes. Contact points were also found to be in a state of ambiguity that seems to be a fused morphology, but the details of the structure remain to be determined by further observations. The above results indicate that the pressure solution process of plagioclase particles can occur on a typical laboratory time scale, and the results of this study provide robust experimental evidences for the theory that links between pressure solution and the mechanism of frictional healing and unstable slips for plagioclase.     

断层物质测年的热释光研究

断层物质ＴＬ测年的关键，是断裂运动产生的温压效应能否使断裂带内某些矿物原贮存的ＴＬ能量完全释放而“归零”。为此，进行了不同条件的高温、高压和位移速率变化等的模拟断裂运动的实验。结果表明，断裂运动产生的摩擦增温是使断层面上矿物ＴＬ强度减弱的主要因素。讨论了摩擦增温值与断裂运动时剪应力大小、断层泥厚度和断层位移间的关系，并得到了野外断层面上实际测试的证实。据此研究成果，还对小湾坝区Ｆ＿７断裂的活动时代进行了测定     

岩石高速摩擦实验与地震物理过程

简述了最近20年来国内外岩石高速摩擦实验研究领域的进展和动态:岩石高速摩擦实验技术的发展实现了对高滑动速率、大位移的地震过程的实验模拟;其结果揭示了岩石和断层泥在地震滑动速率下的力学性状,深化了对断层滑动弱化机制、临界滑动距离、以及地震发生过程的认识和理解;实验在假玄武玻璃成因方面取得了重要进展,并提出了断层发生地震滑动可能留下的其它地质证据,可望为研究断层滑动性状与地震物理过程提供新的思路和信息.岩石高速摩擦实验今后的发展方向主要包括:发展具有加温系统和孔隙压系统的岩石高速摩擦实验装置,研究水热作用下岩石和断层泥的高速摩擦性状;室内实验和地震资料分析相结合研究断层滑动和地震机制;室内实验和野外地质调查相结合探索断层发生地震错动的地质证据等等.     

岩石和断层泥摩擦特性的现场大尺度试件实验研究

为了研究岩石与断层泥的摩擦特性,在远安断裂带附近的灰岩体中开挖试洞、制作试体,进行大尺度试件的现场实验研究.实验用直剪法进行.试体的尺度为506030cm3.试体与岩体间的摩擦面积为3000cm2.摩擦面分为天然断层面、软弱夹层面和节理裂隙面三种.测得的摩擦系数平均值是:（1）天然断层面————0.48;（2）软弱夹层面————0.41;（3）节理裂隙面————0.84.与室内小试件实验结果进行对比,发现现场断层泥的摩擦系数与室内实验结果相近.现场岩石的摩擦系数与室内粗糙岩石的实验结果相近.由于摩擦面积的增大,摩擦面上各点介质屈服的时间有明显的差别.部分摩擦面上介质的较早屈服可作为预报整体失稳的前兆.      

海原断裂带断层泥摩擦特性的研究

用双剪法对海原断裂带5个点的13种断层泥的摩擦滑动特征进行的实验研究表明,海原断裂带的断层泥的存在有助于消除粘滑与增大摩擦强度,五个点断层泥的摩擦系数平均值分别是0.760(景泰),0.728(哈思山),0.669(大沟门),0.644(剌儿沟),0.684(蔡祥堡)。     

Creep,stable sliding,and premonitory slip

Summary The current status of laboratory investigations into creep, stable sliding and premonitory slip is reviewed and some new material is presented. It is postulated that pre-cut rocks and those with simulated gouge layers undergo a transition with increasing confining pressure from (1) stable sliding to stick-slip, to (2) sliding along the pre-cut with deformation of the country rock, to (3) homogeneous flow of the specimen without slip along the pre-cut. Stick-slip behavior is not always present. Decreasing displacement rates are found to enhance stick-slip. Mixtures of gouge are found to be significant in controlling the behavior of sliding with 10–20 percent of anhydrite mixed with quartz or clays mixed with anhydrite shifting the sliding mode from stable stick-slip or stick-slip to stable sliding, respectively. Premonitory slip may be one of the most significant short term precursors of earthquakes. Although widely recognized in the laboratory, little systematic work has been completed. Variations in pore pressure, resistivity and seismic velocities have been investigated. Clearly much work needs to be done into these topics before a clear understanding is achieved.     

Frictional Properties and Microstructure of Calcite-Rich Fault Gouges Sheared at Sub-Seismic Sliding Velocities

We report an experimental and microstructural study of the frictional properties of simulated fault gouges prepared from natural limestone (96 % CaCO₃) and pure calcite. Our experiments consisted of direct shear tests performed, under dry and wet conditions, at an effective normal stress of 50 MPa, at 18–150 °C and sliding velocities of 0.1–10 μm/s. Wet experiments used a pore water pressure of 10 MPa. Wet gouges typically showed a lower steady-state frictional strength (μ = 0.6) than dry gouges (μ = 0.7–0.8), particularly in the case of the pure calcite samples. All runs showed a transition from stable velocity strengthening to (potentially) unstable velocity weakening slip above 80–100 °C. All recovered samples showed patchy, mirror-like surfaces marking boundary shear planes. Optical study of sections cut normal to the shear plane and parallel to the shear direction showed both boundary and inclined shear bands, characterized by extreme grain comminution and a crystallographic preferred orientation. Cross-sections of boundary shears, cut normal to the shear direction using focused ion beam—SEM, from pure calcite gouges sheared at 18 and 150 °C, revealed dense arrays of rounded, ~0.3 μm-sized particles in the shear band core. Transmission electron microscopy showed that these particles consist of 5–20 nm sized calcite nanocrystals. All samples showed evidence for cataclasis and crystal plasticity. Comparing our results with previous models for gouge friction, we suggest that frictional behaviour was controlled by competition between crystal plastic and granular flow processes active in the shear bands, with water facilitating pressure solution, subcritical cracking and intergranular lubrication. Our data have important implications for the depth of the seismogenic zone in tectonically active limestone terrains. Contrary to recent claims, our data also demonstrate that nanocrystalline mirror-like slip surfaces in calcite(-rich) faults are not necessarily indicative of seismic slip rates.     

白云母对岩盐断层带摩擦速度依赖性影响的实验研究

为更好地理解层状硅酸盐对断层强度、滑动速度依赖性及地震活动特征的影响,利用双轴摩擦实验对含白云母岩盐断层带在干燥及含水条件下摩擦的速度依赖性进行了实验研究,并观测了摩擦滑动过程中的声发射,分析了断层带的微观结构.实验结果表明,干燥条件下含白云母岩盐断层带在0.1 ～ 100μm/s的速度范围内表现为黏滑和速度弱化,增大σ2会使断层带从速度弱化向速度强化转化,速度依赖性转换出现在0.1 μm/s,其中断层滑动表现为稳滑或应力释放时间较长的黏滑事件;含水条件下含白云母岩盐断层带在0.05 ～0.01μm/s的速度范围内表现为速度强化,0.1 ～10μm/s的速度范围内表现为速度弱化,50～100μm/s的速度范围内又转换为速度强化行为.含白云母岩盐断层带在干燥条件下一次黏滑伴随一个或一丛声发射事件,而在含水条件下与稳滑相对应,滑动过程中并未记录到声发射事件.显微结构观察表明,速度弱化域的主要变形机制是岩盐颗粒的脆性破裂和局部化的滑动;干燥条件下,速度强化域的主要变形机制是岩盐颗粒的均匀破裂;含水条件下2个速度强化域对应不同的微观机制,高速域的速度强化受控于岩盐颗粒在白云母相互连结形成的网状结构上的滑动及其均匀碎裂作用,而低速域的速度强化还受岩盐的压溶作用控制.通过与岩盐断层带摩擦实验结果对比可知,白云母的存在对于燥岩盐断层带摩擦滑动方式和速度依赖性没有显著影响,而在含水条件下白云母的存在使得岩盐断层带滑动趋于稳定.实验结果为分析含层状硅酸盐断层的强度和稳定性提供了依据.此外,在速度依赖性转换域上观察到的应力缓慢释放的现象进一步证实了在岩盐断层带摩擦滑动过程中观察到的现象,这对慢地震机制研究具有参考意义.     

温度压力孔隙压力对断层泥强度及滑动性质的影响

在不同的压力、温度和孔隙压力下进行了含四种不同断层泥标本的强度试验。碎屑型断层泥对压力很敏感,对温度无反应,对孔隙压力的反应符合有效应力律。粘土类断层泥则对温度和孔隙压力有明显响应。这些力学性质的差别反映了具体变形机制的差别     

地壳深部稳定性——震源体破裂机制和摩擦滑动机制的综合研究

本文通过地壳应力测量结果和地震资料的综合分析,对深部应力状态与断层运动的关系作了讨论:进而应用库仑准则,推导了三维应力作用下完整岩体和已有的任意空间方向断层面的失稳条件及其滑动方式的解析表达式.通过建立描述岩体和已有断层稳定性的两个函数————破裂函数 Fm 和摩擦函数 Ff,给出了应用破裂机制和摩擦滑动机制综合分析地壳稳定性和失稳性态的方法:根据这种分析方法并结合华北平原区的水压致裂应力测量资料,以及孔隙压力、大地热流等观测结果,定量研究了本区地壳的稳定问题,计算并图示了地壳内破裂函数沿深度的分布,以及各种走向和倾向断层面上的摩擦函数和剪应力分布;计算中以 Byerlee 定律作为断层运动的约束条件,并考虑了地壳密度纵向非均匀性导致的垂直应力沿深度的非线性增长以及深部超静水压力的异常孔隙压力作用.结果表明,华北平原区地壳失稳性态主要表现为已有断层的滑动;伴有高剪应力降的断层运动的深度范围在8至2.0多公里之间:陡断层稳定性低于缓断层,其运动方式以走滑为主;本区 NNE-NE 走向的陡断层是一组易震断层,其震时错动为右旋走滑;孔隙压力的增长对地壳稳定性有显著的影响;华北平原区深部高异常孔隙压力是地震活动的一种重要背景.