An explicitly coupled hydro‐geomechanical model for simulating hydraulic fracturing in arbitrary discrete fracture networks

Modeling hydraulic fracturing in the presence of a natural fracture network is a challenging task, owing to the complex interactions between fluid, rock matrix, and rock interfaces, as well as the interactions between propagating fractures and existing natural interfaces. Understanding these complex interactions through numerical modeling is critical to the design of optimum stimulation strategies. In this paper, we present an explicitly integrated, fully coupled discrete‐finite element approach for the simulation of hydraulic fracturing in arbitrary fracture networks. The individual physical processes involved in hydraulic fracturing are identified and addressed as separate modules: a finite element approach for geomechanics in the rock matrix, a finite volume approach for resolving hydrodynamics, a geomechanical joint model for interfacial resolution, and an adaptive remeshing module. The model is verified against the Khristianovich–Geertsma–DeKlerk closed‐form solution for the propagation of a single hydraulic fracture and validated against laboratory testing results on the interaction between a propagating hydraulic fracture and an existing fracture. Preliminary results of simulating hydraulic fracturing in a natural fracture system consisting of multiple fractures are also presented. Copyright © 2012 John Wiley & Sons, Ltd.     

Numerical modeling of hydraulic fracture propagation,closure and reopening using XFEM with application to in‐situ stress estimation

In this paper, a fully coupled model is developed for numerical modeling of hydraulic fracturing in partially saturated weak porous formations using the extended finite element method, which provides an effective means to simulate the coupled hydro‐mechanical processes occurring during hydraulic fracturing. The developed model is for short fractures where plane strain assumptions are valid. The propagation of the hydraulic fracture is governed by the cohesive crack model, which accounts for crack closure and reopening. The developed model allows for fluid flow within the open part of the crack and crack face contact resulting from fracture closure. To prevent the unphysical crack face interpenetration during the closing mode, the crack face contact or self‐contact condition is enforced using the penalty method. Along the open part of the crack, the leakage flux through the crack faces is obtained directly as a part of the solution without introducing any simplifying assumption. If the crack undergoes the closing mode, zero leakage flux condition is imposed along the contact zone. An application of the developed model is shown in numerical modeling of pump‐in/shut‐in test. It is illustrated that the developed model is able to capture the salient features bottomhole pressure/time records exhibit and can extract the confining stress perpendicular to the direction of the hydraulic fracture propagation from the fracture closure pressure. Copyright © 2016 John Wiley & Sons, Ltd.     

CONSEQUENCES OF FLUID LAG IN THREE-DIMENSIONAL HYDRAULIC FRACTURES

Research investigations on three-dimensional (3-D) rectangular hydraulic fracture configurations with varying degrees of fluid lag are reported. This paper demonstrates that a 3-D fracture model coupled with fluid lag (a small region of reduced pressure) at the fracture tip can predict very large excess pressure measurements for hydraulic fracture processes. Predictions of fracture propagation based on critical stress intensity factors are extremely sensitive to the pressure profile at the tip of a propagating fracture. This strong sensitivity to the pressure profile at the tip of a hydraulic fracture is more strongly pronounced in 3-D models versus 2-D models because 3-D fractures are clamped at the top and bottom, and pressures in the 3-D fractures that are far removed from the fracture tip have little effect on the stress intensity factor at the fracture tip. This rationale for the excess pressure mechanism is in marked contrast to the crack tip process damage zone assumptions and attendant high rock fracture toughness value hypotheses advanced in the literature. A comparison with field data is presented to illustrate the proposed fracture fluid pressure sensitivity phenomenon. This paper does not attempt to calculate the length of the fluid lag region in a propagating fracture but instead attempts to show that the pressure profile at the tip of the propagating fracture plays a major role in fracture propagation, and this role is magnified in 3-D models. © 1997 by John Wiley & Sons, Ltd. Int. J. Numer. Anal. Meth. Geomech., vol. 21, 229–240 (1997).     

Simulation of non‐planar three‐dimensional hydraulic fracture propagation

Hydraulic fracturing is the method of choice to enhance reservoir permeability and well efficiency for extraction of shale gas. Multi‐stranded non‐planar hydraulic fractures are often observed in stimulation sites. Non‐planar fractures propagating from wellbores inclined from the direction of maximum horizontal stress have also been reported. The pressure required to propagate non‐planar fractures is in general higher than in the case of planar fractures. Current computational methods for the simulation of hydraulic fractures generally assume single, symmetric, and planar crack geometries. In order to better understand hydraulic fracturing in complex‐layered naturally fractured reservoirs, fully 3D models need to be developed. In this paper, we present simulations of 3D non‐planar fracture propagation using an adaptive generalized FEM. This method greatly facilitates the discretization of complex 3D fractures, as finite element faces are not required to fit the crack surfaces. A solution strategy for fully automatic propagation of arbitrary 3D cracks is presented. The fracture surface on which pressure is applied is also automatically updated at each step. An efficient technique to numerically integrate boundary conditions on crack surfaces is also proposed and implemented. Strongly graded localized refinement and analytical asymptotic expansions are used as enrichment functions in the neighborhood of fracture fronts to increase the computational accuracy and efficiency of the method. Stress intensity factors with pressure on crack faces are extracted using the contour integral method. Various non‐planar crack geometries are investigated to demonstrate the robustness and flexibility of the proposed simulation methodology. Copyright © 2014 John Wiley & Sons, Ltd.     

薄互层水力裂缝垂向扩展控制因素试验研究

新疆油田某地区油藏的储隔层岩性组合复杂,呈现突出的薄互层产状特征,研究合、分压判断条件有利于提高压裂效率,增强储层动用程度与压后改造效果。水力裂缝在薄互层中的穿层与裂缝扩展行为受薄互层地质特征与压裂施工参数的影响。基于此,开展了薄互层物理模型压裂试验,研究界面胶结、岩层分布、岩层厚度、压裂液黏度与注液排量对薄互层中水力裂缝垂向扩展的影响分析。试验结果表明：薄互层的地层特征界面胶结与岩层分布是水力裂缝垂向扩展的主要控制因素,界面胶结强度对裂缝垂向扩展行为的影响强于岩层分布;由于弱胶结界面的存在,水力裂缝垂向扩展穿层时可发生方向偏转,抑制裂缝垂向扩展;提高压裂液黏度与注液排量有利于薄互层中水力裂缝的穿层垂向扩展。     

Anisotropic porothermoelastic solution and hydro‐thermal effects on fracture width in hydraulic fracturing

In this study, the effects of the temperature difference between hydraulic fracturing fluid and rock formation on the time‐dependent evolution of fracture width were investigated using a newly derived one‐dimensional anisotropic porothermoelastic analytical solution. The solution is shown to correctly reproduce existing solutions for special cases and corrections for an earlier publication are provided. An analysis of time‐dependent fracture width evolution using Woodford Shale data was also presented. It was found that when the fracturing fluid has the same temperature as the shale formation, the fracture gradually closes back after the initial opening due to the invasion of the fracturing fluid. Practically, in this scenario, proppants should be pumped into the fracture as soon as possible to obtain maximum fracture conductivity. On the other hand, with a fracturing fluid 60 °C colder than the formation, the thermal contraction of the rock dominates the fracture aperture evolution, resulting in a fracture aperture approximately 70% larger than that produced by the hotter fracturing fluid. Consequently, in this case, it is beneficial to delay proppant placement to take advantage of the widening fractures. Finally, it was found that the fracture aperture is directly controlled by the spacing of natural fractures. Therefore, the presence of natural fractures in the shale formation and their spacing influence not only the type of hydraulic fractures created but also what kind and size of proppants should be used to keep them open. Copyright © 2013 John Wiley & Sons, Ltd.     

基于ABAQUS平台的水力裂缝扩展有限元模拟研究

随着扩展有限元理论的深入研究,利用扩展有限元方法模拟水力压裂具有了一定的可操作性。相比于常规有限元方法,XFEM方法具有计算结果精度高和计算量小的优点。但是,如何模拟射孔孔眼、如何模拟流体与岩石相互作用以及分析水力裂缝的扩展规律仍然是难题。以研究水力压裂裂缝扩展规律为目的,建立了岩石多孔介质应力平衡方程、流体渗流连续性方程和边界条件。通过有限元离散化方法对耦合方程矩阵进行处理。通过富集函数定义初始裂缝（射孔孔眼）,选择最大主应力及损伤变量D分别作为裂缝起裂和扩展判定准则,利用水平集方法模拟水力裂缝扩展过程。数值模拟结果显示：增加射孔方位角、压裂液排量和减小水平地应力差,起裂压力上升;黏度对起裂压力无明显影响。增加射孔方位角、压裂液排量、黏度和减小水平地应力差值有助于裂缝宽度的增加。增加水平地应力差值、压裂液排量和减小射孔方位角以及压裂液黏度有助于裂缝长度增加,反之亦然。基于ABAQUS的水力裂缝扩展有限元法可对不同井型和诸多储层物性参数及压裂施工参数进行分析,且裂缝形态逼真,裂缝面凹凸程度清晰,结果准确。此研究可作为一种简便有效研究水力压裂裂缝扩展规律的方法为油田水力压裂设计与施工提供参考与依据。     

青海共和盆地干热岩地热储层水力压裂物理模拟和裂缝起裂与扩展形态研究

水力压裂是青海共和盆地干热岩地热资源开发的难点技术问题之一。本文基于升级改造的大尺寸真三轴水力压裂物理模拟实验系统模拟干热岩储层高温高压环境,利用青海共和盆地露头岩心进行水力压裂物理模拟实验,揭示干热岩储层水力裂缝的起裂和扩展规律。通过物理模拟实验发现：干热岩储层裂缝起裂可以通过文中提出的起裂模型判断起裂方式和预测起裂压力;水力裂缝在岩石基质中的扩展形态简单,仅沿最大主应力方向延伸;但是水力裂缝会受到岩石中弱面的影响,发生转向沿弱面延伸,形成较复杂的裂缝形态。因此,建议在干热岩储层实际施工中,在天然裂缝发育较丰富的层段开展水力压裂,以实现复杂裂缝网络提取地热能。     

煤岩水力压裂裂缝扩展形态试验研究

通过室内水力压裂物理模拟试验系统,对大尺寸原煤进行了水力压裂模拟试验,根据水力裂缝的空间展布形态分析了煤岩储层水力裂缝的延伸规律,揭示了网状裂缝的形成机制。结果表明：水力裂缝易在弱层理处分叉和转向,发育的层理和裂缝系统等结构面为压裂形成裂缝网络提供了前提条件。泵压曲线呈现出的频繁波动是煤岩内产生网状裂缝的一个显著特征。水力裂缝的起裂与延伸有4种基本模式,裂缝网络的形成多为这4种基本模式的组合。地应力差异系数和泵注排量对煤层水力裂缝形态有较大影响。较小的地应力差异系数更利于网状裂缝的形成;较高的压裂液排量易形成相对简单的裂缝形态,导致压裂改造效果较差。该试验方法和试验结果可为现场水力压裂参数设计和优化提供参考和依据。     

砂砾岩水力压裂裂缝扩展规律的数值模拟分析

砂砾岩储层一般具有岩性和渗透性变化大、孔隙度低、连通性差、孔隙结构复杂和非均匀性严重等特点,因此,在水力压裂过程中,裂缝扩展形态难以控制,大规模改造难度大。针对国内某典型砂砾岩油藏特征,采用数值计算方法对砂砾岩压裂裂缝的扩展规律进行了研究,包括地应力场、砾石含量和粒径等对裂缝扩展形态及压裂压力的影响。研究表明,砾石的存在增加了压裂裂纹扩展的复杂性,裂纹主要有止裂、偏转、穿透和吸附4种表现模式,但主应力差严格控制着裂纹的走向,随着主应力差的增大,裂纹由总体绕砾扩展转变为总体穿砾扩展,失稳压力随着主应力差的增大而明显减小;砾石含量的多少体现了砂砾岩试样宏观的非均匀性,含量越高均匀性越差,随着砾石含量的提高,裂纹与砾石的相互作用占据主导地位,失稳压力随砾石含量的增加而增大;当砾石体积含量一定时,砾石粒径对压裂压力的影响主要取决于砾石排列的随机性,失稳压力随砾石粒径的增大而略有增大。     

超临界CO2岩石致裂机制分析

超临界CO2是一种介于气体和液体之间的特殊状态的CO2流体,具有低黏、高扩散性和零表面张力等独特的性质。利用超临界CO2作为压裂液,有助于裂缝的起裂和扩展,同时可避免储层伤害。通过研究超临界CO2射流破岩和压裂特性,分析得到了超临界CO2岩石致裂机制。研究结果表明,超临界CO2低黏等特性使其更容易进入岩石微孔和微缝之中,在岩石内部建立大小不一的流体压力系统,使岩石发生拉伸和剪切破坏;常规流体压裂起裂压力较高,裂缝一般为单条或多条平直裂缝,大多沿着同一方向贯穿强度较高的胶结颗粒,且裂缝断面光滑、平整;超临界CO2压裂起裂压力相比于常规流体压裂低,在岩石中形成的裂缝网络较为复杂,裂缝互相连通,一般沿着强度较低的胶结物开裂,较少贯穿胶结颗粒,裂缝断面较为粗糙。该研究结果可为超临界CO2压裂技术的实施提供理论支撑。     

Solution for a plane strain rough‐walled hydraulic fracture driven by turbulent fluid through impermeable rock

The impact of turbulent flow on plane strain fluid‐driven crack propagation is an important but still poorly understood consideration in hydraulic fracture modeling. The changes that hydraulic fracturing has experienced over the past decade, especially in the area of fracturing fluids, have played a major role in the transition of the typical fluid regime from laminar to turbulent flow. Motivated by the increasing preponderance of high‐rate, water‐driven hydraulic fractures with high Reynolds number, we present a semianalytical solution for the propagation of a plane strain hydraulic fracture driven by a turbulent fluid in an impermeable formation. The formulation uses a power law relationship between the Darcy‐Weisbach friction factor and the scale of the fracture roughness, where one specific manifestation of this generalized friction factor is the classical Gauckler‐Manning‐Strickler approximation for turbulent flow in a rough‐walled channel. Conservation of mass, elasticity, and crack propagation are also solved simultaneously. We obtain a semianalytical solution using an orthogonal polynomial series. An approximate closed‐form solution is enabled by a choice of orthogonal polynomials embedding the near‐tip asymptotic behavior and thus giving very rapid convergence; a precise solution is obtained with 2 terms of the series. By comparison with numerical simulations, we show that the transition region between the laminar and turbulent regimes can be relatively small so that full solutions can often be well approximated by either a fully laminar or fully turbulent solution.     

煤岩水力压裂起裂压力和裂缝扩展机制实验研究

为了研究煤岩水力压裂的起裂压力和水力压裂裂缝扩展规律,采用型煤试样,利用自主研发的水力压裂实验系统,参照现场压裂施工制定了“施加三向应力-顶部注水”的煤岩水力压裂物理模拟实验方案并开展了水力压裂实验,分析了不同条件下泵注压力和水力压裂裂缝。实验结果表明:压裂液泵注排量越大,起裂压力越大。三向应力满足最大水平主应力σ_H > 垂向应力σ_v > 最小水平主应力σ_h,水力压裂裂缝沿着垂直于σ_h的方向扩展。σ_v和σ_h一定,随着σ_H的增大,煤岩起裂压力先增大后减小,水力压裂裂缝扩展路径越平直。当σ_H远大于σ_v和σ_h时,水力压裂裂缝扩展路径越复杂,分叉缝角度越大。研究结果可为煤岩水力压裂理论的完善提供一定的参考和借鉴。      

A numerical investigation of the hydraulic fracturing behaviour of conglomerate in Glutenite formation

Rock formations in Glutenite reservoirs typically display highly variable lithology and permeability, low and complex porosity, and significant heterogeneity. It is difficult to predict the pathway of hydraulic fractures in such rock formations. To capture the complex hydraulic fractures in rock masses, a numerical code called Rock Failure Process Analysis (RFPA2D) is introduced. Based on the characteristics of a typical Glutenite reservoir in China, a series of 2D numerical simulations on the hydraulic fractures in a small-scale model are conducted. The initiation, propagation and associated stress evolution of the hydraulic fracture during the failure process, which cannot be observed in experimental tests, are numerically simulated. Based on the numerical results, the hydraulic fracturing path and features are illustrated and discussed in detail. The influence of the confining stress ratio, gravel sizes (indicated by the diameter variation), and gravel volume content (VC) on the hydraulic fracturing pattern in a conglomerate specimen are numerically investigated, and the breakdown pressure is quantified as a function of these variables. Five hydraulic fracturing modes are identified: termination, deflection, branching (bifurcation), penetration, and attraction. The propagation trajectory of the primary hydraulic fractures is determined by the maximum and minimum stress ratios, although the fracturing path on local scales is clearly influenced by the presence of gravels in the conglomerate, particularly when the gravels are relatively large. As the stress ratio increases, the fractures typically penetrate through the gravels completely rather than propagating around the gravels, and the breakdown pressure decreases with increasing stress ratio. Furthermore, the breakdown pressure is affected by the size and volume content of the gravel in the conglomerate: as the gravel size and volume content increase, the breakdown pressure increases.     

孔隙水压力对岩石裂纹扩展影响的数值模拟

应用岩石破坏过程渗流-应力-损伤(FSD)耦合分析软件F-RFPA2D,通过对孔隙水压作用下岩石试件加载破坏过程的数值模拟,对孔隙水压力大小和梯度对岩石试样中裂纹的萌生和扩展进行了数值模拟研究。模拟结果再现了孔隙水压力作用下裂纹萌生扩展的全过程,表明孔隙水压力大小和梯度对岩石中裂纹的萌生和扩展模式都有很大的影响。     

A stabilized extended finite element framework for hydraulic fracturing simulations

We present a stabilized extended finite element formulation to simulate the hydraulic fracturing process in an elasto‐plastic medium. The fracture propagation process is governed by a cohesive fracture model, where a trilinear traction‐separation law is used to describe normal contact, cohesion and strength softening on the fracture face. Fluid flow inside the fracture channel is governed by the lubrication equation, and the flow rate is related to the fluid pressure gradient by the ‘cubic’ law. Fluid leak off happens only in the normal direction and is assumed to be governed by the Carter's leak‐off model. We propose a ‘local’ U‐P (displacement‐pressure) formulation to discretize the fluid‐solid coupled system, where volume shape functions are used to interpolate the fluid pressure field on the fracture face. The ‘local’ U‐P approach is compatible with the extended finite element framework, and a separate mesh is not required to describe the fluid flow. The coupled system of equations is solved iteratively by the standard Newton‐Raphson method. We identify instability issues associated with the fluid flow inside the fracture channel, and use the polynomial pressure projection method to reduce the pressure oscillations resulting from the instability. Numerical examples demonstrate that the proposed framework is effective in modeling 3D hydraulic fracture propagation. Copyright © 2016 John Wiley & Sons, Ltd.     

Numerical Modeling of Natural Fracture Distributions in Shale

The production efficiency of shale gas is affected by the interaction between hydraulic and natural fractures. This study presents a simulation of natural fractures in shale reservoirs, based on a discrete fracture network (DFN) method for hydraulic fracturing engineering. Fracture properties of the model are calculated from core fracture data, according to statistical mathematical analysis. The calculation results make full use of the quantitative information of core fracture orientation, density, opening and length, which constitute the direct and extensive data of mining engineering. The reliability and applicability of the model are analyzed with regard to model size and density, a calculation method for dominant size and density being proposed. Then, finite element analysis is applied to a hydraulic fracturing numerical simulation of a shale fractured reservoir in southeastern Chongqing. The hydraulic pressure distribution, fracture propagation, acoustic emission information and in situ stress changes during fracturing are analyzed. The results show the application of fracture statistics in fracture modeling and the influence of fracture distribution on hydraulic fracturing engineering. The present analysis may provide a reference for shale gas exploitation.     

Numerical simulation of particle plugging in hydraulic fracture by element partition method

Hydraulic fracturing (HF) treatment often involves particle migration and is applied for propping or plugging fractures. Particle migration behaviors, e.g., bridging, packing, and plugging, significantly affect the HF process. Hence, it is crucial to effectively simulate particle migration. In this study, a new numerical approach is developed based on a coupled element partition method (EPM). The EPM is used to model natural and hydraulic fractures, in which a fracture is allowed to propagate across an element, thereby avoiding remeshing in fracture simulations. To characterize the water flow process in a fracture, a fully hydromechanical coupled equation is adopted in the EPM. To model particle transportation in fractures with water flow, each particle is treated as a discrete element. The particles move in the fracture as a result of being dragged by fluid. Their movement, contact, and packing behaviors are simulated using the discrete element method. To reflect the plugging effect, an equivalent aperture approach is proposed. Using this method, the particle migration and its effect on water flow are well simulated. The simulation results show that this method can effectively reproduce particle bridging, plugging, and unblocking in a hydraulic fracture. Furthermore, it is demonstrated that particle plugging significantly affects water flow in a fracture and hence the propagation of hydraulic fracture. This method provides a simple and feasible approach for the simulation of particle migration in a hydraulic fracture.     

Discrete fracture model for simulating waterflooding processes under fracturing conditions

In our study, we develop a model for simulating fracturing processes in a poroelastic medium. The proposed approach combines the discrete fracture model enriched with contact plane mechanics. The model captures mechanical interactions of fractures and a deformable medium, fluid, and heat transfer in fractures and in a porous medium. Both effects of poroelasticity and thermoelasticity are accounted in our model. Mass and heat conservation equations are approximated by the finite volume method, and mechanical equilibrium equations are discretized by means of the Galerkin finite element approach. Two‐dimensional grid facets between 3‐dimensional finite elements are considered as possible fracture surfaces. Most of these facets are inactive from the beginning and are activated throughout the simulation. A fracture propagation criterion, based on Irwin's approach, is verified on each nonlinear iteration. When the criterion is satisfied, additional contact elements are added into finite element and discrete fracture model formulations respectively. The proposed approach allows modeling of existing natural and artificially created fractures within one framework. The model is tested on single‐ and multiple‐phase fluid flow examples for both isothermal and thermal conditions and verified against existing semianalytical solutions. The applicability of the approach is demonstrated on an example of practical interests where a sector model of an oil reservoir is simulated with different injection and production regimes.     

Modeling of dynamic cohesive fracture propagation in porous saturated media

In this paper, a mathematical model is presented for the analysis of dynamic fracture propagation in the saturated porous media. The solid behavior incorporates a discrete cohesive fracture model, coupled with the flow in porous media through the fracture network. The double‐nodded zero‐thickness cohesive interface element is employed for the mixed mode fracture behavior in tension and contact behavior in compression. The crack is automatically detected and propagated perpendicular to the maximum effective stress. The spatial discretization is continuously updated during the crack propagation. Numerical examples from the hydraulic fracturing test and the concrete gravity dam show the capability of the model to simulate dynamic fracture propagation. The comparison is performed between the quasi‐static and fully dynamic solutions, and the performance of two analyses is investigated on the values of crack length and crack mouth opening. Copyright © 2010 John Wiley & Sons, Ltd.