基于Landsat 8影像的黄河口悬浮物质量浓度遥感反演

悬浮物质量浓度是黄河口海域重要的水质和水环境监测参数之一,直接影响着水面以下光场的分布,进而影响水体的初级生产力和水域生态环境。本文基于2011年6—7月和11—12月共计89组现场实测悬浮物质量浓度和光谱数据,分析了黄河口及其附近海域不同悬浮物质量浓度的水体光谱特征,尝试利用多种波段组合建立悬浮物质量浓度遥感反演算法。结果表明865 nm波段与波段比655 nm/560 nm组合形式算法反演结果最优,算法相关系数R²为0.95,平均相对误差为25.65%。将算法应用于2014—2016年共7景Landsat 8 OLI遥感影像,分析了不同年份黄河口悬浮物质量浓度的时空分布特征,黄河口海域悬浮物质量浓度分布总体呈现近岸高,离岸低的特点,不同时期悬浮物质量浓度量值上有显著变化。     

基于半分析方法的黄河口悬浮物浓度遥感反演

河口区的悬浮物浓度受陆源输入和水动力等其他因素的影响严重,具有重要研究意义。本文利用黄河口及其邻近区域采集的145个站位光谱数据和悬浮物(Suspended Particulate Matter,SPM)浓度数据,检验了Nechad模型、多波段准分析算法(Quasi-Analytical Algorithm,QAA)、最优化模型和半经验辐射传输模型(Semi-Empirical Radiative Transfer,SERT)在黄河口水域的适用性。结果表明,QAA561模型和Nechad561模型在低浓度水域反演结果较好,QAA655模型反演结果较差,Nechad665模型适合于低浓度水域,但反演精度低。QAA865模型和Nechad865模型在中高浓度水域的反演结果较好。SERT655模型反演精度较低。最优化模型和SERT滑动模型的反演精度较高。由于黄河口水域悬浮物浓度变化范围较大,因此,本文建立了分段QAA模型和Nechad模型。分段模型的反演结果均优于单一模型。根据误差敏感性分析可知,Nechad分段模型和QAA分段模型对于遥感反射率的50%以内的误差不敏感,稳定可靠。将分段模型应用于Landsat-8 OLI数据,获取了悬浮物浓度时空分布图。结果表明,反演结果与已有研究具有相似的分布特征。两种模型得到的悬浮物浓度在数值上存在差异,然而分布趋势在中高浓度季节有非常好的一致性。     

基于分析模型的太湖悬浮物浓度遥感监测

悬浮物浓度是水质评价的一项重要指标,利用遥感技术准确获取区域面状水域悬浮物浓度信息,是遥感监测水质参数的一项重要任务。利用地面实测的14个样点的光谱数据,将2004年7月26日太湖TM数据的DN值,校正为遥感反射率,并利用Gordon模型和太湖水体固有光学特性,建立水体反射率模拟的分析模型,模拟水体R(0-),进而利用TM数据反演水体悬浮物浓度,并绘制太湖悬浮物浓度分布图。将悬浮物浓度反演的结果与14个样点的实测结果相比较,其中,有79%的样点的估计精度高于70%,有64%的样点的估计精度高于80%。     

基于SDGSAT-1影像的总悬浮物浓度反演方法研究

总悬浮物浓度是海洋的重要水质参数之一,其对水体透明度、水下光场及初级生产力有显著影响,同时对河流入海口与海岸带冲淤变化过程有重要作用。本文基于我国自主研制的SDGSAT-1卫星遥感影像,使用准分析算法（Quasi-Analytical Algorithm,QAA）获取水体固有光学量,并结合2022年4月黄河口区域总悬浮物浓度实测数据,建立水体固有光学量与总悬浮物浓度实测数据的单波段、波段加减、波段比值,以及多波段组合等模型并开展遥感反演,最后将反演结果同实测数据及基于Sentinel-2B影像的总悬浮物浓度反演结果进行对比。研究结果表明：基于SDGSAT-1影像的总悬浮物浓度反演结果在黄河口高浓度区域的决定系数为0.622,均方根误差为7.94 mg/L;基于Sentinel-2B影像的总悬浮物浓度反演结果在黄河口高浓度区域的决定系数为0.589,均方根误差为8.27 mg/L。故在我国近岸海域总悬浮物浓度反演方面,SDGSAT-1影像反演精度与Sentinel-2B影像反演精度相媲美。     

渤海悬浮物分布的遥感研究

利用渤海湾和莱州湾现场实测的悬浮物含量和光谱数据,建立了基于555和670nm波段遥感反射率的悬浮物含量遥感反演模型。经检验,模型平均相对误差优于20%,对输入端误差不敏感。基于该模型,利用ENVISAT MERIS遥感数据,从空间分布格局、大风过程的短期扰动以及季节性差异等方面分析了渤海悬浮物的时空分布特征。(1)渤海悬浮物含量的高值区集中分布在莱州湾(尤其是黄河口和莱州湾湾底)和渤海湾沿岸,此外在辽东湾沿岸海域悬浮物含量也相对较高,而在渤海大部水体悬浮物含量较低。(2)大风过程可在短期内(约1~3d)显著改变全渤海的悬浮物空间分布格局,其中渤海湾和莱州湾响应最为强烈,辽东湾响应相对较弱,这与其各自的水深条件、底质类型和悬浮物粒径等因素有关。(3)渤海悬浮物含量总体上呈春夏低、秋冬高的分布特征;季节性差异最显著的区域是渤海湾、莱州湾和辽东湾,差异性最小的是秦皇岛近岸海域;风力等气候因素是悬浮物分布呈现季节性差异的主要原因,入海径流是另一重要因素。     

黄、东海二类水体水色要素的统计反演模式

根据高质量的现场实测数据,借鉴Tassan模式,得到了中国黄、东海近岸二类水体水色要素统计反演模式,填补了中国近岸二类水体水色遥感三要素反演模式的空白.现场测量数据的反演与实测的平均相对误差分别为 Chl-a 36 %～45 %,总悬浮物浓度20 %～30 %,黄色物质约为20 %.对该三要素统计模式对遥感反射率误差的敏感性进行了分析.模式比较表明,中国黄、东海长江口近岸水体的模型,特别是高浑浊度水体区域,与国际其他水体的模型参数有较大的差异.     

辽东湾水体吸收系数区域性半分析反演算法

水体吸收系数是影响水体光场分布的重要参数,在水色遥感探测中受到广泛关注。本文利用2012年9月辽东湾区域航次调查数据分析该区域水体各组分吸收系数的分布情况,结果表明,辽东湾水体中浮游植物含量相对较高。并利用该航次数据,建立了区域性半分析算法,该算法基于相邻波段间固有光学量的线性关系,首先通过遥感反射率反演得到550 nm波段的水体总吸收系数,再通过后向散射波段相关关系外推得到其他波段的总吸收系数。经独立测试数据检验,3个波段(412、443、550 nm)总吸收系数反演的平均相对误差分别为19.71%,17.99%,9.35%,说明区域性半分析算法能较好地估算研究区域的水体总吸收系数。本文还通过引入随机误差对算法稳定性进行了检验,结果表明算法具有较好的稳定性。     

近海水体悬浮物HJ-1 号小卫星CCD 定量反演研究

基于H J-1号小卫星CCD数据,开展近海水体悬浮物含量监测研究.采用邻近清洁水体和同日MODIS气溶胶产品的方法对CCD辐亮度数据进行较精准的大气校正;利用得到的水体遥感反射率,结合地面准同步实测悬浮物含量数据建立悬浮物反演模型,获得研究区悬浮物的空间分布.模型的相关系数R2为0.849,平均误差为33.0％,反演结果较为理想.结果表明,HJ-1号小卫星作为中国首个灾害监测小卫星星座,能够实现定量反演近海水体的悬浮物含量,对中国近海水体水质的监测和治理具有重要意义.     

渤海悬浮物分布的遥感研究渤海悬浮物分布的遥感研究

利用渤海湾和莱州湾现场实测的悬浮物含量和光谱数据，建立了基于555和670 nm波段遥感反射率的悬浮物含量遥感反演模型。经检验，模型平均相对误差优于20%，对输入端误差不敏感。基于该模型，利用ENVISAT MERIS遥感数据，从空间分布格局、大风过程的短期扰动以及季节性差异等方面分析了渤海悬浮物的时空分布特征。（1）渤海悬浮物含量的高值区集中分布在莱州湾（尤其是黄河口和莱州湾湾底）和渤海湾沿岸，此外在辽东湾沿岸海域悬浮物含量也相对较高，而在渤海大部水体悬浮物含量较低。（2）大风过程可在短期内（约1~3 d）显著改变全渤海的悬浮物空间分布格局，其中渤海湾和莱州湾响应最为强烈，辽东湾响应相对较弱，这与其各自的水深条件、底质类型和悬浮物粒径等因素有关。（3）渤海悬浮物含量总体上呈春夏低、秋冬高的分布特征；季节性差异最显著的区域是渤海湾、莱州湾和辽东湾，差异性最小的是秦皇岛近岸海域；风力等气候因素是悬浮物分布呈现季节性差异的主要原因，入海径流是另一重要因素     

图像融合技术在海阳核电工程建设区域表层悬沙浓度遥感反演中的应用

本研究分别采用根据高时间分辨率的GOCI(Geostationary Ocean Imager)数据和高空间分辨率的OLI影像反演得到的悬浮泥沙浓度产品,利用STARFM(Spatial and Temporal Adaptive Reflectance Fusion Model)融合算法,生成高时空分辨率的悬浮泥沙浓度产品,融合后的数据兼具OLI影像的高空间分辨率和GOCI影像的高时间分辨率。与实测数据相比, GOCI原始数据反演的相对误差为56%,融合图像的反演相对误差降低至36%。融合影像可用于探讨研究区从高潮到低潮时期表层悬浮泥沙完整变化,便于分析海阳核电工程建设区域的悬浮泥沙分布受潮流变化的影响,进而了解核电工程建设通过影响悬沙分布对周围环境产生的影响。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.