Strain-Rate Dependent Stress--Strain Behavior of Undisturbed Hong Kong Marine Deposits under Oedometric and Triaxial Stress States

This article presents a testing study on the strain-rate effects on the stress--strain behavior of natural, undisturbed Hong Kong marine deposits (HKMD) from three Hong Kong locations, including a one-dimensional (1-D) compressibility in a confined condition, and undrained shear strengths in triaxial compression and extension modes. The influences of the strain rates on the one-dimensional compressibility are studied by means of constant rate of strain (CRS) tests and multistage loading oedometer (MSL) tests, and those on the undrained shear strengths are studied by K_o-consolidated undrained compression and extension tests with step-changed axial strain rates (CK_oUC and CK_oUE tests), and with both step-changed axial strain rates and relaxation processes (CK_oUCR and CK_oUER tests). The strain-rate effects on the stress--strain behavior are generally examined by “apparent” preconsolidation pressures in the 1-D compressions and undrained shear strengths in the triaxial compression and extension stress states. The stress--strain behavior of the natural, undisturbed HKMD exhibits considerable viscous characteristics. In the CRS and MSL tests at a given strain, the higher the strain rate, the higher the effective stress, the higher the porewater pressure. In the undrained shearing tests, the higher the strain rate, the higher the undrained shear strength, but the lower the porewater pressure. For the CK_oUC and CK_oUE tests on the Tsing Yi site samples, the undrained shear strength increases by 8.5% and 12.1% for one order increment of axial strain rate of 0.2%/hr (i.e., ρ_0.2) for the compression and extension modes respectively. For the CK_oUCR and CK_o tests on the Tung Chung site samples of different compositions, average ρ_0.2 is increased by 6.2% for the compression and 9.5% for the extension, but by 18.8% for the extension on a higher plastic sample. The present study shows that the strain-rate effects on the stress--strain behavior of the undisturbed HKMD are larger for specimens in extension than those in compression.     

Strain-Rate Dependent Stress--Strain Behavior of Undisturbed Hong Kong Marine Deposits under Oedometric and Triaxial Stress States

ABSTRACT

This article presents a testing study on the strain-rate effects on the stress--strain behavior of natural, undisturbed Hong Kong marine deposits (HKMD) from three Hong Kong locations, including a one-dimensional (1-D) compressibility in a confined condition, and undrained shear strengths in triaxial compression and extension modes. The influences of the strain rates on the one-dimensional compressibility are studied by means of constant rate of strain (CRS) tests and multistage loading oedometer (MSL) tests, and those on the undrained shear strengths are studied by K _o-consolidated undrained compression and extension tests with step-changed axial strain rates (CK _oUC and CK _oUE tests), and with both step-changed axial strain rates and relaxation processes (CK _oUCR and CK _oUER tests). The strain-rate effects on the stress--strain behavior are generally examined by “apparent” preconsolidation pressures in the 1-D compressions and undrained shear strengths in the triaxial compression and extension stress states. The stress--strain behavior of the natural, undisturbed HKMD exhibits considerable viscous characteristics. In the CRS and MSL tests at a given strain, the higher the strain rate, the higher the effective stress, the higher the porewater pressure. In the undrained shearing tests, the higher the strain rate, the higher the undrained shear strength, but the lower the porewater pressure. For the CK _oUC and CK _oUE tests on the Tsing Yi site samples, the undrained shear strength increases by 8.5% and 12.1% for one order increment of axial strain rate of 0.2%/hr (i.e., ρ_0.2) for the compression and extension modes respectively. For the CK _oUCR and CK _o tests on the Tung Chung site samples of different compositions, average ρ_0.2 is increased by 6.2% for the compression and 9.5% for the extension, but by 18.8% for the extension on a higher plastic sample. The present study shows that the strain-rate effects on the stress--strain behavior of the undisturbed HKMD are larger for specimens in extension than those in compression.     

Mechanical Characteristics of Light-Weighted Soils Using Dredged Materials

This study investigates the mechanical characteristics of light-weighted soils (LWS) consisting of expanded polystyrene (EPS), dredged clays, and cement through both unconfined and triaxial compression tests. The mechanical characteristics of the compressive strength of LWS are analyzed with varying initial water contents of dredged clays, EPS ratio, cement ratio, and curing pressure. In the triaxial compression test, it is found that the compressive strength of LWS associated with EPS is independent on the effective confining pressure. When both EPS ratio is less than 2% and cement ratio is more than 2%, the compressive strength rapidly decreases after the ultimate value. This signifies that the compressive strength-strain behavior is quite similar to that of the cemented soil. The ground improved by LWS has the compressive strength of 200 kPa associated with the optimized EPS ratio of 3-4% and initial water content of 165-175%. The ultimate compressive strength under both triaxial and unconfined compression tests is almost constant for a cement ratio of up to 2%.     

Shear Strength of Jumunjin Sand according to Relative Density

The properties of sands pertaining to shear strength have been studied extensively by plane strain and triaxial tests for relative densities above 40%. Unfortunately, properties of sand have not been comprehensively studied for relative density below 40%. An experimental investigation of the shear strength of Jumunjin sand was carried out using a plane strain, triaxial and direct shear apparatus according to relative density ranges from 0 to 100%. Because of the complexity of the shear tests on coarse materials, correlations were developed that would be useful for practical purposes. This article presents a comparison of strength properties' results and their correlation with relative density.     

Mechanical Behavior of Light-Weight Soil Under Consolidated Drained Shear Condition

To reveal the influence of material composition on mechanical properties of light-weight soil, stress-strain -volumetric strain characteristics and Poisson's ratio of mixed soil were researched by consolidated drained shear tests. The results show that light-weight soil is a kind of structural soil, so its mechanical properties are affected by mixed ratio and confining pressure, and mixed soil possesses structural yield stress. When confining pressure is less than the structural yield stress, strain softening occurs; when confining pressure is more than the structural yield stress, strain hardening is observed. There are two kinds of volume change behavior: shear contraction and shear dilatancy. Shear dilatancy usually leads to strain softening, but there isn't an assured causal relationship between them. Poisson's ratio of mixed soil is a variational state parameter with the change of stress state, it decreases with increased confining pressure, and it increases with increased stress level. When axial strain is near 5%, Poisson’ ratio is gradually close to a steady value. The main range of Poisson's ratio is 0.25～0.50 when confining pressure changes from 50 to 300 kPa. When unconfined compressive strength of mixed soil is less than 328 kPa, its stress-strain-volumetric strain characteristics can be predicted very well by Duncan-Chang model (E-B model). However, when the range of unconfined compressive strength is [328 kPa, 566 kPa], the model can't predict stress-strain characteristics accurately when confining pressure is under 200 kPa, and it also can't predict the strong shear dilatancy phenomenon of mixed soil under low confining pressure.     

Post-Cyclic Behavior of Carbonate Sand of the Northern Coast of the Persian Gulf

The post-cyclic behavior of biogenic carbonate sand was evaluated using cyclic triaxial testing through a stress control method under different confining pressures between 50 to 600 kPa. The testing program included a series of isotropically and anisotropically consolidated, undrained triaxial compression and extension tests on samples of remolded calcareous Bushehr sand. Grading analyses (before and after each test) were used to examine the influence of particle breakage on post-cyclic behavior of Bushehr sand. The particle breakage commonly occurred in these soils even in lower values of confining pressure, yet there was not a clear correlation between the post-cyclic responses and particle breakage. Based on the present study, a concept is suggested for post-cyclic behavior of carbonate sand. It was observed that post-cyclic strength has a good correlation with cyclic stress ratio, type of consolidation, and value of residual cyclic strain. For all specimens, it is clear that the post-cyclic strength is greater than monotonic strength, irrespective of confining pressure and relative density.     

Undrained Monotonic Response and Instability of Medium-Dense Sandy Soil

A series of undrained monotonic triaxial compression tests were performed on natural, medium-dense (relative density (RD) = 50%) Chlef sand containing 0.5% of non-plastic fines, under different confining pressures of 50 kPa, 100 kPa, and 200 kPa. This article focuses on distinctive states of the monotonic undrained response of sands, namely the critical state, the phase transformation state, the quasi-steady state, and the state of undrained instability (onset of flow liquefaction). Specimens were prepared using dry funnel pluviation and wet deposition to investigate the effect of the initial sand fabric on these states. The present data suggest that the initial fabric of the sand appears to have a significant effect on the undrained behavior in the early stages of shearing, with its influence vanishing at large strains. Wet deposition specimens demonstrate considerably larger undrained instability state strength than their dry funnel pluviation counterparts, and a unique critical state locus is reached by both dry funnel pluviation and wet deposition.     

海洋粉质粘土在波浪荷载作用后的不排水抗剪强度衰化特性

通过对南海重塑粉质粘土土样的大量动三轴试验结果分析,得到此种土在波浪荷载作用后不捧水抗剪强度衰化同动载作用引起的动应变幅及平均累积孔压之间的相互关系和预估公式;并通过与超固结土样的静三轴剪切试验结果的比较,发现动、静三轴两种试验结果具有很好的吻合关系。建议可用超固结土样的静三轴剪切试验同时结合部分动三轴试验来预估土样在波浪荷载作用后不排水抗剪强度衰化与平均累积孔压之间的关系。     

Strength Behavior of Marine Sands at Elevated Confining Stresses

A testing program was initiated to determine the stress-strain and strength behavior of two very different marine sands (a calcareous sediment from South Australia and a siliceous sediment from the United Kingdom) at elevated confining pressures. The testing matrix consisted of a series of isotropically consolidated, undrained (CIU) and drained (CID), triaxial compression tests on samples of naturally deposited calcareous and siliceous sediment and remolded calcareous sediment. It was found that the calcareous samples displayed little cemented behavior during shear. For tests conducted at pressures up to 1.5 MPa, a significant amount of particle crushing occurred in the calcareous samples but not in the siliceous samples. Particle degradation and reorientation facilitates transitions from dilative to contractive behavior with increases in confining stress. The calcareous sediment exhibited contractive behavior at confining pressures above approximately 500 kPa and the siliceous sediment remained dilative at stresses up to 1 MPa during undrained loading. Comparison with data collected by the University of Sydney (CID tests with confining pressures up to 60 MPa) showed that most of the variations in strength behavior occurred within the low stress range (up to 2 MPa) tests conducted at URI. This was evident in the friction angle data and in the reloading Young's modulus data.     

Shearing response of geotextile-reinforced calcareous soils using monotonic triaxial tests

Abstract

Different types of geosynthetic reinforcements have been widely used for improving shear strength of soil materials in recent decades. In this study, two different calcareous soils reinforced by geotextile layers were evaluated by monotonic compression triaxial tests. The calcareous soils were obtained from Hormuz Island and Boushehr Port located in the north coast of the Persian Gulf. Different reconstituted samples were prepared at dense conditions with and without geotextile layers and consolidated under different effective confining pressures ranging from 100 to 600?kPa. Different layers of reinforcements including one, two and three geotextile layers were placed in the reinforced samples and sheared under drained condition. The results show that confining pressure has a significant effect on the efficiency of reinforcements. Evidently, increasing the reinforcement layers decreased the particle breakage of the calcareous soils used in this study.     

低围压水平下砂的排水行为(英文)

采用干样沉降法制备样品 ,选用静三轴仪对松砂和密砂样在 10 k Pa至 10 0 k Pa的低围压下的排水行为进行了实验研究 ,并对实验结果作了橡皮膜校正 ,在围压为 10 k Pa的密砂实验中 ,轴向应力的校正值可达到 12 %。实验研究表明低围压下松砂的剪胀性非常明显 ,且存在剪应力极值 ;围压越低 ,松砂和密砂的剪应力极值越小 ,达到最大剪应力所对应的剪应变越小。同时还表明低围压范围内相对密度不同 ,砂的应力应变特性不同 ;此外 ,低围压下砂的内摩擦角高于高围压下的值 ,从而在工程上应重视低围压水平下砂土工程参数的合理选取     

Experimental study on the cyclic behavior of loose calcareous sand under linear stress paths

Abstract

Hollow cylinder torsional shear tests on loose isotropically and anisotropically consolidated calcareous sand were conducted to investigate the cyclic behavior under three different linear stress paths, including horizontal line, oblique line, and vertical line stress paths, in a coordinate system of the normal stress difference and the horizontal shear stress. The dominant strain components of the isotropically consolidated specimens are affected by the stress paths. With increasing consolidation stress ratio, axial strain gradually becomes the dominant strain component under the three different stress paths. The cyclic strength of the isotropically consolidated specimens under the three different stress paths are almost the same, while for the anisotropically consolidated specimens, the cyclic strengths are strongly affected by the stress paths. These results indicate that conventional cyclic triaxial tests may overestimate cyclic strength in some cases. Irrespective of the stress paths and cyclic stress ratios, the terminal residual excess pore pressure ratio decreases with increasing consolidation stress ratio. Moreover, an empirical equation is proposed to describe the relationship between the normalized shear work and the normalized residual excess pore pressure ratio. The comparative study reveals that the relationship proposed for silica sand is not suitable for the dynamic analyses of calcareous sand.     

Effects of Mudstone Particle Content on Shear Strength of a Crushed Sandstone–Mudstone Particle Mixture

The present study focuses on the shear strength, deformation, and particle crushing of sand which is mixed by crushed sandstone and mudstone particles. Two triaxial tests—one for unsaturated specimens and the other for saturated specimens—were performed, along with sieve analysis tests. Results obtained from the triaxial tests indicate that, with the increment of the mudstone particle content by weight, the angle of internal friction decreases, the cohesion increases and then decreases, and both the initial angle of shearing resistance at the atmospheric pressure and decremental angle increase and then decrease. Compared to the unsaturated specimens, the deviator stress or normalized deviator stress of the saturated specimens at the same axial stress may decrease due to the wetting action. Thus, the shear strength of the tested materials may be reduced by the wetting action. Results of sieve analysis tests indicate that the mixing of some mudstone particles into the sandstone particle mixture may reduce the amount of particle crushing, but the wetting action may increase the amount. The amount of the crushed particle may arrive at a minimum of 40% of mudstone particle content by weight.     

Mechanical Characteristics of Light-Weighted Soils Using Dredged Materials

This study investigates the mechanical characteristics of light-weighted soils (LWS) consisting of expanded polystyrene (EPS), dredged clays, and cement through both unconfined and triaxial compression tests. The mechanical characteristics of the compressive strength of LWS are analyzed with varying initial water contents of dredged clays, EPS ratio, cement ratio, and curing pressure. In the triaxial compression test, it is found that the compressive strength of LWS associated with EPS is independent on the effective confining pressure. When both EPS ratio is less than 2% and cement ratio is more than 2%, the compressive strength rapidly decreases after the ultimate value. This signifies that the compressive strength-strain behavior is quite similar to that of the cemented soil. The ground improved by LWS has the compressive strength of 200 kPa associated with the optimized EPS ratio of 3–4% and initial water content of 165–175%. The ultimate compressive strength under both triaxial and unconfined compression tests is almost constant for a cement ratio of up to 2%.     

循环应力下饱和黏土剪切变形特性试验研究

针对饱和重塑黏土,利用土工静力-动力液压三轴-扭转多功能剪切仪,在不固结不排水(UU)条件下进行了应力控制式循环扭剪和竖向-扭转耦合试验,通过对试验结果的对比分析探讨了初始预剪应力和应力反向对应力-应变关系特性的影响,并阐述了不同加荷模式下孔隙水压力发展特性。以此为基础,综合考虑剪切变形和正向偏差变形的共同效应,同时为了能够反映平均残余变形和循环变形的影响,建议了一个综合应变破坏标准的算式。进而通过利用试验数据与目前常用的应变标准比较,表明这种破坏标准具有普遍适用性和较好的稳定性,适用于判定各种应力条件下黏土试样破坏及其强度。     

Laboratory study of shear strength response of Chlef natural sand: Effect of saturation

Abstract

The study of the unsaturated soils is a very complex field to which several researches in laboratory and on site are directed these last years. An experimental study aims to quantify the influence of the Skempton coefficient B characterizing the degree of saturation on the behavior of the granular sand to the liquefaction resistance of sand. The study is based on undrained triaxial tests performed on natural Chlef sand carried out at an initial relative density Dr = 50% under a confining pressure of 50, 100 and 200?kPa for Skempton coefficient B?=?10 to 92%. The results of the tests show that an increase of confining pressure leads to an increase of the shear stress of the samples. For the lower value of the degree of saturation results of our findings indicate an increase of the resistance to liquefaction; our results are in good agreement with others observed in several research projects conducted with other sands. The increase of Skempton coefficient B induces an increase of pore water pressure and a decrease of the shear strength. The pore pressure (u) increases with an exponential manner with the increase of the degree of saturation; while the residual shear strength (Rs) decreases with logarithmic manner with the increase of degree of saturation (B).     

A simple experimental method to regain the mechanical behavior of naturally structured marine clays

Quantitative laboratory studies on the structural behavior of natural intact marine clays require a large number of identical natural samples leading to an expensive and challenging task. This study proposes a simple method to reconstruct an artificial structured marine clay as the state of its natural intact clay at both macro and micro levels. For this purpose, the Shanghai marine clay is selected and mixed with low cement contents (1–6%). The clay-cement slurry is mixed in a container with the ice-covered sides at a low temperature about 0 ± 2 °C to postpone the hydration reactions until consolidation began. The purpose of adding cement is to generate the inter-particle bonding and structure in reconstituted samples. Initially, the reconstituted samples are consolidated under the in situ stress of 98 kPa and then under the pre-consolidation pressure of 50 kPa. Mechanical characteristics such as compression index, yield stress, unconfined compression strength, shear strength ratio, and the stress paths from triaxial tests are compared with natural intact clay accordingly. Scanning electron microscope and mercury intrusion porosimetry analyses are also performed to analyze the microstructure of clays for comparison. Furthermore, the proposed method is also examined by using natural intact marine clays of different locations and characteristics.     

分段多项式拟合在动三轴试验数据处理中的应用

动三轴采集的试验数据点(剪应变与动剪模量和阻尼比之间)具有离散性和有限性,为方便应用需要对数据点进行拟合,但现有经验公式不一定很好吻合试验数据。为得到不同剪应变与对应的动剪模量和阻尼比之间的关系,本文利用最小二乘原理,对渤海某海洋平台地基土进行动三轴试验获得的动剪模量、阻尼比与剪切应变的数据进行了分段多项式的拟合。数据处理过程是先对剪应变值进行了压缩处理,然后再分段低次多项式拟合,得到多项式拟合参数。通过此项改进解决了正规方程解中的病态问题,且拟合效果良好。     

Short-Term Stability Evaluation of an Embankment Constructed on Marine Clay Foundation at Kobe Airport

This article introduces the application of a stability analysis method that accounts for strength anisotropy on the embankment constructed at the Kobe airport. Shear strength anisotropy is induced by the in-situ state of stress along a potential slip surface of the embankment. In addition, the effects of the shearing rate on the undrained shear strength of the marine clay are examined in detail based on the results of a series of constant-volume direct shear box (DSB), triaxial compression (TC), and triaxial extension (TE) tests varying shearing rates. The most critical slip surface was selected from the deterministic slope stability analysis using unconfined compression tests of undisturbed clay samples from the field. For the most critical slip surface, the potential factor of safety of the embankment is estimated to be within the range of 1.21 to 1.28, as indicated by the results of the stability analyses using the strengths obtained from the DSB, TC, and TE tests and varying shearing rates.     

含水合物粉细砂的三轴试验及模拟

利用水饱和法制备含天然气水合物试样,进行等向压缩试验和不排水三轴试验.采用天然气水合物临界状态(M HCS)模型同时预测排水条件和不排水条件下的三轴试验,并进行变动参数分析.不排水条件下,密实纯砂发生应变硬化,而相近密实度的含水合物试样出现应变软化,峰值偏应力随水合物饱和度和围压增大.通过与排水和不排水三轴试验结果的对...