城市建筑动力学效应对对流边界层影响的敏感性试验

本文将大涡模拟应用于城市对流边界层(CBL)湍流结构和流场特征的研究,在大涡模式中,拖曳系数取与建筑物高度及建筑物高度标准差有关的表达式以考虑次网格建筑物对风速和湍流动能(TKE)的面积平均影响.模拟结果表明,由于城市建筑物对气流的拖曳作用,使建筑物冠层及整个CBL内风速大幅度减小,城市冠层内部风速减小尤为明显,在夹卷层内,风速有一明显的跃变.在边界层中部对流运动已经发展成为较强的热泡,城市建筑物的动力学效应使热泡的水平尺度增大,CBL内平均上升气流速度和下沉气流速度减小,同时使CBL中上升气流所占比例比平坦地面增大.城市建筑物使CBL低层热通量、动量通量、速度方差和位温方差明显增大,但对近地层高度以上的湍流量影响不大.     

The Budget of Turbulent Kinetic Energy in the Urban Roughness Sublayer

Full-scale observations from two urban sites in Basel, Switzerland were analysed to identify the magnitude of different processes that create, relocate, and dissipate turbulent kinetic energy (TKE) in the urban atmosphere. Two towers equipped with a profile of six ultrasonic anemometers each sampled the flow in the urban roughness sublayer, i.e. from street canyon base up to roughly 2.5 times the mean building height. This observational study suggests a conceptual division of the urban roughness sublayer into three layers: (1) the layer above the highest roofs, where local buoyancy production and local shear production of TKE are counterbalanced by local viscous dissipation rate and scaled turbulence statistics are close to to surface-layer values; (2) the layer around mean building height with a distinct inflexional mean wind profile, a strong shear and wake production of TKE, a more efficient turbulent exchange of momentum, and a notable export of TKE by transport processes; (3) the lower street canyon with imported TKE by transport processes and negligible local production. Averaged integral velocity variances vary significantly with height in the urban roughness sublayer and reflect the driving processes that create or relocate TKE at a particular height. The observed profiles of the terms of the TKE budget and the velocity variances show many similarities to observations within and above vegetation canopies.     

Aircraft-Based Measurements Of Turbulence Structures In The Katabatic Flow Over Greenland

Turbulence structures in the katabatic flow in the stable boundary layer (SBL) over the ice sheet are studied for two case studies with high wind speeds during the aircraft-based experiment KABEG (Katabatic wind and boundary layer front experiment around Greenland) in the area of southern Greenland. The aircraft data allow the direct determination of turbulence structures in the katabatic flow. For the first time, this allows the study of the turbulence structure in the katabatic wind system over the whole boundary layer and over a horizontal scale of 80 km.The katabatic flow is associated with a low-level jet (LLJ), with maximum wind speeds up to 25 m s^-1. Turbulent kinetic energy (TKE) and the magnitude of the turbulent fluxes show a strong decrease below the LLJ. Sensible heat fluxes at the lowest level have values down to -25 W m^-2. Latent heat fluxes are small in general, but evaporation values of up to +13 W m^-2 are also measured. Turbulence spectra show a well-defined inertial subrange and a clear spectral gap around 250-m wavelength. While turbulence intensity decreases monotonously with height above the LLJ for the upper part of the slope, high spectral intensities are also present at upper levels close to the ice edge. Normalized fluxes and variances generally follow power-law profiles in the SBL.Terms of the TKE budget are computed from the aircraft data. The TKE destruction by the negative buoyancy is found to be very small, and the dissipation rate exceeds the dynamical production.     

Large-Eddy Simulations of Surface Heterogeneity Effects on the Convective Boundary Layer During the LITFASS-2003 Experiment

We investigate the impact of observed surface heterogeneities during the LITFASS-2003 experiment on the convective boundary layer (CBL). Large-eddy simulations (LES), driven by observed near-surface sensible and latent heat fluxes, were performed for the diurnal cycle and compare well with observations. As in former studies of idealized one- and two-dimensional heterogeneities, secondary circulations developed that are superimposed on the turbulent field and that partly take over the vertical transport of heat and moisture. The secondary circulation patterns vary between local and roll-like structures, depending on the background wind conditions. For higher background wind speeds, the flow feels an effective surface heat-flux pattern that derives from the original pattern by streamwise averaging. This effective pattern generates a roll-like secondary circulation with roll axes along the mean boundary-layer wind direction. Mainly the upstream surface conditions control the secondary circulation pattern, where the fetch increases with increasing background wind speed. Unlike the entrainment flux that appears to be slightly decreased compared to the homogeneously-heated CBL, the vertical flux of sensible heat appears not to be modified in the mixed layer, while the vertical flux of latent heat shows different responses to secondary circulations. The study illustrates that sufficient time averaging and ensemble averaging is required to separate the heterogeneity-induced signals from the raw LES turbulence data. This might be an important reason why experiments over heterogeneous terrain in the past did not give any clear evidence of heterogeneity-induced effects.     

Temporal Evolution of Low-Level Winds Induced by Two-dimensional Mesoscale Surface Heat-Flux Heterogeneity

Using large-eddy simulation (LES), the effects of mesoscale local surface heterogeneity on the temporal evolution of low-level flows in the convective boundary layer driven by two-dimensional surface heat-flux variations are investigated at a height of about 100 m over flat terrain. The surface variations are prescribed with sinusoids of wavelength 32 km and varying amplitudes of 0, 50, 100, and 200 W m $^{-2}$ . The Weather Research and Forecasting numerical model is used as a mesoscale-domain LES model that has a grid spacing fine enough to explicitly resolve energy-containing turbulent eddies and a model domain large enough to include mesoscale circulations. Mesoscale circulations induced by the two-dimensional surface heterogeneity may undergo a flow transition and an associated spectral energy cascade, which has been found previously but only with one-dimensional surface heat-flux variations. Over a strongly heterogeneous surface prescribed with a two-dimensional sinusoid of amplitude 200 W m $^{-2}$ , the domain-averaged variance of the horizontal wind component initially grows rapidly, then undergoes a flow transition and subsequently rapidly decays. With a background wind, the induced mesoscale circulations are inhibited in the streamwise direction. However in the spanwise direction, somewhat stronger mesoscale circulations are induced, compared with those with no background wind. The background wind attenuates the significant reduction of the low-level temperature gradient by the fully-developed mesoscale horizontal flow. Spectral decomposition reveals that this rapid transition also exists in the mesoscale horizontal flows induced by the intermediate surface heterogeneity prescribed with a sinusoid of amplitude 100 W m $^{-2}$ . However the transition is masked by continuously growing turbulence.     

A New Scheme for the Simulation of Microscale Flow and Dispersion in Urban Areas by Coupling Large-Eddy Simulation with Mesoscale Models

A coupling scheme is proposed for the simulation of microscale flow and dispersion in which both the mesoscale field and small-scale turbulence are specified at the boundary of a microscale model. The small-scale turbulence is obtained individually in the inner and outer layers by the transformation of pre-computed databases, and then combined in a weighted sum. Validation of the results of a flow over a cluster of model buildings shows that the inner- and outer-layer transition height should be located in the roughness sublayer. Both the new scheme and the previous scheme are applied in the simulation of the flow over the central business district of Oklahoma City (a point source during intensive observation period 3 of the Joint Urban 2003 experimental campaign), with results showing that the wind speed is well predicted in the canopy layer. Compared with the previous scheme, the new scheme improves the prediction of the wind direction and turbulent kinetic energy (TKE) in the canopy layer. The flow field influences the scalar plume in two ways, i.e. the averaged flow field determines the advective flux and the TKE field determines the turbulent flux. Thus, the mean, root-mean-square and maximum of the concentration agree better with the observations with the new scheme. These results indicate that the new scheme is an effective means of simulating the complex flow and dispersion in urban canopies.     

ON THE PDF MODELS FOR ATMOSPHERIC DIFFUSION IN BOUNDARY LAYER

In this paper, taking its turbulent exchange coefficient as a function of the Lagrangian timescale and standard variance of the turbulence in atmosphere, the atmospheric dispersion PDFmodels are obtained on the basis of atmospheric diffusion K-theory. In the model the statistics ofwind speed are directly used as its parameters instead of classic dispersion parameters. The bi-Gaussian PDF is derived in convective boundary layer (CBL), from the statistics of verticalvelocity in both of the downdraft and updraft regions that are investigated theoretically in the otherpart of this paper. Giving the driven parameters of the CBL (including the convective velocity scalew* and the mixing depth h_i) and the time-averaged wind speed at release level, the PDF model isable to simulate the distribution of concentration released at any levels in the CBL. The PDF'ssimulations are fairly consistent with the measurements in CONDORS experiment or the resultsbrought out by some numerical simulations.     

论边界层中的大气扩散PDF模式

基于大气扩散Ｋ理论，用作为风速脉动均方差和拉氏时间尺度函数的湍流交换系数，得到了直接利用风速脉动几率密度而不用扩散参数的大气扩散ＰＤＦ模式。分别研究了对流边界层上升气流区与下降区垂直速度的统计特征，求得双正态ＰＤＦ模式。在给定ＣＢＬ自身参数如对流特征速度ｗ＊，顶高ｈｉ和源高度上的平均风速时，该模式计算出的无量纲浓度分布与室内外测试结果一致。     

Parameterization of sheared entrainment in a well-developed CBL. Part I: Evaluation of the scheme through large-eddy simulations

The entrainment flux ratio A _e and the inversion layer (IL) thickness are two key parameters in a mixed layer model. A _e is defined as the ratio of the entrainment heat flux at the mixed layer top to the surface heat flux. The IL is the layer between the mixed layer and the free atmosphere. In this study, a parameterization of A _e is derived from the TKE budget in the firstorder model for a well-developed CBL under the condition of linearly sheared geostrophic velocity with a zero value at the surface. It is also appropriate for a CBL under the condition of geostrophic velocity remaining constant with height. LESs are conducted under the above two conditions to determine the coefficients in the parameterization scheme. Results suggest that about 43% of the shear-produced TKE in the IL is available for entrainment, while the shear-produced TKE in the mixed layer and surface layer have little effect on entrainment. Based on this scheme, a new scale of convective turbulence velocity is proposed and applied to parameterize the IL thickness. The LES outputs for the CBLs under the condition of linearly sheared geostrophic velocity with a non-zero surface value are used to verify the performance of the parameterization scheme. It is found that the parameterized A _e and IL thickness agree well with the LES outputs.     

Turbulence intensity and turbulent kinetic energy parameters over a heterogeneous terrain of Loess Plateau

A deep understanding of turbulence structure is important for investigating the characteristics of the atmospheric boundary layer, especially over heterogeneous terrain. In the present study, turbulence intensity and turbulent kinetic energy (TKE) parameters are analyzed for different conditions with respect to stability, wind direction and wind speed over a valley region of the Loess Plateau of China during December 2003 and January 2004. The purpose of the study is to examine whether the observed turbulence intensity and TKE parameters satisfy Monin-Obukhov similarity theory (MOST), and analyze the wind shear effect on, and thermal buoyancy function of, the TKE, despite the terrain heterogeneity. The results demonstrate that the normalized intensity of turbulence follows MOST for all stability in the horizontal and vertical directions, as well as the normalized TKE in the horizontal direction. The shear effect of the wind speed in the Loess Plateau region is strong in winter and could enhance turbulence for all stability conditions. During daytime, the buoyancy and shear effect together constitute the generation of TKE under unstable conditions. At night, the contribution of buoyancy to TKE is relatively small, and mechanical shearing is the main production form of turbulence.     

A Variable Mesh Spacing for Large-Eddy Simulation Models in the Convective Boundary Layer

A variable vertical mesh spacing for large-eddy simulation (LES) models in a convective boundary layer (CBL) is proposed. The argument is based on the fact that in the vertical direction the turbulence near the surface in a CBL is inhomogeneous and therefore the subfilter-scale effects depend on the relative location between the spectral peak of the vertical velocity and the filter cut-off wavelength. From the physical point of view, this lack of homogeneity makes the vertical mesh spacing the principal length scale and, as a consequence, the LES filter cut-off wavenumber is expressed in terms of this characteristic length scale. Assuming that the inertial subrange initial frequency is equal to the LES filter cut-off frequency and employing fitting expressions that describe the observed convective turbulent energy one-dimensional spectra, it is feasible to derive a relation to calculate the variable vertical mesh spacing. The incorporation of this variable vertical grid within a LES model shows that both the mean quantities (and their gradients) and the turbulent statistics quantities are well described near to the ground level, where the LES predictions are known to be a challenging task.     

A numerical study of the marine stratocumulus cloud layer

A one-dimensional grid-level model including longwave radiative transfer and a level-4 second-order turbulent transfer closure which contains prognostic equations for turbulent quantities, is used to study the physics and dynamics of inversion-capped marine stratocumulus clouds.A set of numerical experiments had been performed to examined the role of sea surface temperature, large-scale vertical velocity, wind speed, and vertical wind shear in the formation and the structure of low-level clouds. For a given sea surface and geostrophic wind speed, stratocumulus clouds can grow higher with smaller large-scale subsidence as less dry air entrains into the cloud. Clouds grow higher with higher sea surface temperature for a given geostrophic wind speed and large-scale subsidence as a result of enhanced moist convection. In high wind speeds, the entire cloud deck is lifted up because of larger surface energy flux. In the budget studies of the turbulent kinetic energy (TKE), the buoyancy term is a major source term when the wind speed and the vertical shear are small across the inversion top. When the wind speed and the vertical wind shear across the inversion top become large, the mixed layer is decoupled into a cloud and a subcloud layer. In the TKE budget studies, the shear generation term becomes an important term in the budgets of the TKE and the variance of vertical velocity.     

MM5模式中城市冠层参数化方案的设计及其数值试验

文中在综合国外一些较先进的中尺度模式城市作用参数化方案的基础上 ,从城市下垫面结构对城市边界层大气作用的物理机制及实际应用两方面出发 ,对城市下垫面结构和人为活动等因素对边界层结构的影响及中尺度模式中城市化作用的合理体现等问题进行了较全面的考虑 ,改进和设计出能够较全面、细致地描述城市结构对大气边界层动力、热力结构的影响 ,且适合中尺度模式结构特点的城市冠层参数化方案 (UCP) ,并实现了其与MM5模式的耦合。进行了耦合后的UCP方案及采用原城市作用方案的MM5模式对BECAPEX试验期间北京地区气象条件多重嵌套细尺度进行了模拟试验 ,并与观测结果对比 ,结果表明 :相比于MM 5模式中原有表示城市作用的参数化方案来讲 ,设计的UCP方案在很大程度上提高了MM 5模式对城市边界层热力和动力结构的模拟能力。     

风切变对边界层对流影响的大涡模拟研究

利用"西北干旱区陆-气相互作用野外观测实验"加密观测期间在敦煌站的观测资料以及大涡模式,模拟了对流边界层的发展,以及示踪物从混合层向残留层传输的时空变化。模拟的对流边界层的结构及演变特征与实测结果基本一致。进一步通过有风切变和无风切变的敏感性数值试验,研究了风切变对垂直速度、位温和示踪物浓度的水平分布以及示踪物传输高度的影响。研究结果表明,在有风切变的试验中(甚至风切变仅存在于近地层中),对流边界层的增长加强,而且示踪物被传输的高度也较高。与浮力驱动的对流边界层相比,由浮力和风切变共同驱动的边界层中上升气流较弱而下沉气流较强,但前者的上升气流与下沉气流的分布在垂直方向上更为倾斜。由于夹卷作用的增强,浮力和风切变共同驱动的对流边界层较浮力驱动的对流边界层暖。在夹卷层,浮力和风切变共同驱动的边界层对流的上升气流和下沉气流都比浮力驱动的边界层对流中的强,而且垂直速度的概率密度函数分布也较对称,其位温和示踪物浓度的概率密度函数分布也比浮力驱动的边界层中的平直。对湍流动能收支的分析也表明风切变对湍流动能有重要影响,尤其对夹卷层中的湍流动能切变产生项影响较大。示踪物浓度的概率密度函数垂直分布显示,浮力驱动的边界层中示踪物浓度随高度变化较小,而浮力和风切变共同驱动的边界层中示踪物浓度随高度递减,但是示踪物传输的高度比较高。     

基于风廓线仪的华南地区夏季边界层湍流统计特征研究

采用双权重算法,使用2015年6—8月我国东南部业务风廓线雷达资料,通过湍流脉动垂直速度方差和偏度的计算和分析,对晴空和低云主导情况下的边界层湍流特征以及中小尺度局地环流对于边界层湍流的影响进行研究。主要结论如下:(1)晴天情况下垂直速度标准差和垂直速度偏度都具有明显的日变化特征,湍流主要由下垫面加热驱动发展;(2)在低云主导情况下,湍流明显弱于晴天对流边界层的湍流强度,边界层内湍流的发展不仅受地面加热的影响,而且在边界层上部存在明显的自上而下发展的湍流,这主要是由于边界层顶云辐射冷却造成的;(3)除了上述两种情况,边界层湍流发展同时受到局地中小尺度环流或者天气系统的影响,因而呈现出更多的复杂性。      

Large-Eddy Simulation of Flow and Pollutant Transport in Urban Street Canyons with Ground Heating

Our study employed large-eddy simulation (LES) based on a one-equation subgrid-scale model to investigate the flow field and pollutant dispersion characteristics inside urban street canyons. Unstable thermal stratification was produced by heating the ground of the street canyon. Using the Boussinesq approximation, thermal buoyancy forces were taken into account in both the Navier–Stokes equations and the transport equation for subgrid-scale turbulent kinetic energy (TKE). The LESs were validated against experimental data obtained in wind-tunnel studies before the model was applied to study the detailed turbulence, temperature, and pollutant dispersion characteristics in the street canyon of aspect ratio 1. The effects of different Richardson numbers (Ri) were investigated. The ground heating significantly enhanced mean flow, turbulence, and pollutant flux inside the street canyon, but weakened the shear at the roof level. The mean flow was observed to be no longer isolated from the free stream and fresh air could be entrained into the street canyon at the roof-level leeward corner. Weighed against higher temperature, the ground heating facilitated pollutant removal from the street canyon.     

Effects of Temporal Discretization on Turbulence Statistics and Spectra in Numerically Simulated Convective Boundary Layers

Six state-of-the-art large-eddy simulation codes were compared in Fedorovich et al. (Preprints, 16th American Meteorological Society Symposium on Boundary Layers and Turbulence, 2004b) for three airflow configurations in order to better understand the effect of wind shear on entrainment dynamics in the convective boundary layer CBL). One such code was the University of Oklahoma large-eddy simulation (LES) code, which at the time employed a second-order leapfrog time-advancement scheme with the Asselin filter. In subsequent years, the code has been updated to use a third-order Runge–Kutta (RK3) time-advancement scheme. This study investigates what effect the upgrade from the leapfrog scheme to RK3 scheme has on turbulence statistics in the CBL differently affected by mean wind shear, also in relation to predictions by other LES codes that participated in the considered comparison exercise. In addition, the effect of changing the Courant number within the RK3 scheme is investigated by invoking the turbulence spectral analysis. Results indicate that low-order flow statistics obtained with the RK3 scheme generally match their counterparts from simulations with the leapfrog scheme rather closely. CBL growth rates due to entrainment in the shear-free case were also similar using both timestepping schemes. It was found, however, that care should be given to the choice of the Courant number value when running LES with the RK3 scheme in the sheared CBL setting. The advantages of the largest possible (based on the stability criterion) Courant number were negated by degrading the energy distribution across the turbulence spectrum. While mean profiles and low-order turbulence statistics were largely unaffected, the entrainment rate was over-predicted compared to that reported in the original code-comparison study.     

Large-eddy Simulation of Turbulent Flow across a Forest Edge. Part II: Momentum and Turbulent Kinetic Energy Budgets

Momentum and turbulent kinetic energy (TKE) budgets across a forest edge have been investigated using large-eddy simulation (LES). Edge effects are observed in the rapid variation of a number of budget terms across this vegetation transition. The enhanced drag force at the forest edge is largely balanced by the pressure gradient force and by streamwise advection of upstream momentum, while vertical turbulent diffusion is relatively insignificant. For variance and TKE budgets, the most important processes at the forest edge are production due to the convergence (or divergence) of the mean flow, streamwise advection, pressure diffusion and enhanced dissipation by canopy drag. Turbulent diffusion, pressure redistribution and vertical shear production, which are characteristic processes in homogeneous canopy flow, are less important at the forest transition. We demonstrate that, in the equilibrated canopy flow, a substantial amount of TKE produced in the streamwise direction by the vertical shear of the mean flow is redistributed in the vertical direction by pressure fluctuations. This redistribution process occurs in the upper canopy layers. Part of the TKE in the vertical velocity component is transferred by turbulent and pressure diffusion to the lower canopy levels, where pressure redistribution takes place again and feeds TKE back to the streamwise direction. In this TKE cycle, the primary source terms are vertical shear production for streamwise velocity variance and pressure redistribution for vertical velocity variance. The evolution of these primary source terms downwind of the forest edge largely controls the adjustment rates of velocity variances.     

Bridging the Transition from Mesoscale to Microscale Turbulence in Numerical Weather Prediction Models

With a focus towards developing multiscale capabilities in numerical weather prediction models, the specific problem of the transition from the mesoscale to the microscale is investigated. For that purpose, idealized one-way nested mesoscale to large-eddy simulation (LES) experiments were carried out using the Weather Research and Forecasting model framework. It is demonstrated that switching from one-dimensional turbulent diffusion in the mesoscale model to three-dimensional LES mixing does not necessarily result in an instantaneous development of turbulence in the LES domain. On the contrary, very large fetches are needed for the natural transition to turbulence to occur. The computational burden imposed by these long fetches necessitates the development of methods to accelerate the generation of turbulence on a nested LES domain forced by a smooth mesoscale inflow. To that end, four new methods based upon finite amplitude perturbations of the potential temperature field along the LES inflow boundaries are developed, and investigated under convective conditions. Each method accelerated the development of turbulence within the LES domain, with two of the methods resulting in a rapid generation of production and inertial range energy content associated to microscales that is consistent with non-nested simulations using periodic boundary conditions. The cell perturbation approach, the simplest and most efficient of the best performing methods, was investigated further under neutral and stable conditions. Successful results were obtained in all the regimes, where satisfactory agreement of mean velocity, variances and turbulent fluxes, as well as velocity and temperature spectra, was achieved with reference non-nested simulations. In contrast, the non-perturbed LES solution exhibited important energy deficits associated to a delayed establishment of fully-developed turbulence. The cell perturbation method has negligible computational cost, significantly accelerates the generation of realistic turbulence, and requires minimal parameter tuning, with the necessary information relatable to mean inflow conditions provided by the mesoscale solution.