超低硬度隔震橡胶支座的竖向力学性能研究

为了解具有超低硬度(G值为0.196 MPa,简称G2)的天然隔震橡胶支座(简称LNR)及铅芯隔震橡胶支座(简称LRB)的竖向力学性能,采用试验方法对不同直径G2-LNR支座和G2-LRB支座进行了不同压力下竖向刚度、不同水平剪应变下竖向静刚度及不同水平连续剪切位移下支座附加竖向变形测试,对同直径G值为0.392MPa(简称G4)支座部分相同性能进行了对比测试,并将G2测试结果和理论分析结果进行了对比.测试结果表明,G2-LNR竖向刚度随竖向压力的增加呈线性增加的趋势,其不同剪应变状态下竖向静刚度随应变增加呈线性减少的趋势.G2-LRB竖向刚度随竖向压力的增加呈非线性增加,而不同剪应变状态下竖向静刚度随应变未呈现明显的变化规律.试验与理论分析结果表明,测试得到的不同剪应变状态下支座竖向静刚度与理论计算得到的支座刚度在大应变时误差较大.支座不同剪应变状态下竖向静刚度难以准确反映支座在连续水平剪应变状态下的真实刚度,采用藤田隆史考虑重叠面积竖向刚度公式可以较好地预计G2支座在不同剪切位移时支座的附加沉降位移.     

方形多铅芯橡胶支座力学性能研究

本文通过对方形多铅芯橡胶支座竖向压缩性能试验,水平剪切性能试验以及其等效刚度、屈服强度、屈服后刚度、等效阻尼比等水平特征参数与水平剪切应变和竖向压应力的关系,特别是对其在不同方向上压缩剪切变形状态下的性能试验,分析了这种隔震支座各种水平特征参数在不同方向上变化的相关规律。得出在这种类型橡胶隔震支座在双向水平荷载同时作用下,竖向性能和水平性能较为稳定,是较为理想的桥梁结构的减隔震装置。     

建筑用低硬度橡胶隔震支座界限性能和屈曲性能研究

本研究系统地对低硬度橡胶隔震支座的材料及力学性能进行了试验研究。研究用低硬度橡胶天然及铅芯橡胶隔震支座18种规格总计近30个大直径隔震支座。研究内容涉及低硬度橡胶隔震支座的基本力学性能，温度、压力、剪切变形、老化及徐变等相关性能，压缩界限、拉伸界限、极限剪切变形等界限性能和屈曲特性，以及橡胶材料性能和隔震工程应用等方面。本文主要介绍低硬度橡胶天然及铅芯隔震支座的压缩、拉伸、剪切等界限性能和屈曲应力与剪切应变的相关特性，文中提出了基于刚度因子建立的橡胶支座的界限压缩和界限拉伸应力评价方程，同时还给出了剪切变形状态下的屈曲应力评价方法。     

橡胶座非线性弹性压缩特性的理论和试验研究

本文系统地研究分析了与橡胶隔震支座(以下简称为橡胶座)压缩特性有关的基础理论，提出了原点纵向压缩弹性模量、原点压缩刚度、偏压弹性模量、偏压竖向刚度的基本概念，同时还提出了计算剪切变形状态下橡胶座竖向刚度的计算理论。基于纯压缩原点竖向刚度和偏压原点刚度理论，提出了预测橡胶座压缩变形量的计算理论。文中针对新提出的概念和计算理论采用天然橡胶和铅芯橡胶座共计16个原型试件进行了系统的试验研究工作，试验结果表明本文建立的计算理论能够较理想地定量分析橡胶座的刚度和变形特性。     

夹层橡胶隔震支座全刚性性能、回转刚性及高压缩应力性能试验研究

本文详细地研究了夹层橡胶隔震支座的全刚性性能,同时还研究了夹层 橡胶隔震支座的回刚性,并给出了竖向压力及剪切变形对隔震支座回转刚性的影响结果,文末给出了隔震支座在高压缩应力作用下的基本力学性能,研究结果显示在竖向压缩压力达到30MPa时,隔震支座仍可具有良好的力学性能。     

金属橡胶支座剪切性能试验研究

针对一种金属橡胶支座,研究其剪切性能。进行3种压应力下的拟静力试验,分析竖向压力和水平剪切变形对支座剪切性能的影响;以试验数据为基准,建立支座剪切性能与压应力之间的相关性经验公式,提出能够近似模拟试验曲线的三线性恢复力模型。试验研究表明,随着支座剪切变形的增大,支座等效刚度及耗能增大,等效阻尼比减小,屈服力基本保持不变,滞回曲线由梭形逐渐变为反S型,当剪切应变大于25%时支座出现刚度硬化现象;随着支座压应力增大,支座的耗能、屈服力、等效刚度及等效阻尼比均增大。     

岩石变形局部化的实验研究

用光弹贴片法、声发射技术和电视录象的方法,研究了山东济南辉长岩试件（15×45×90mm³）。在平面应力状态下,单轴压缩加载的过程中,岩石表面（45×90mm²）的应变场的等差线（即最大剪切应变的等值线）条纹图案的连续变化过程。 在加载到峰值载荷的88％-95％时,高级次的等差线条纹在包含即将发生的断层面的区带中高度集中。变形集中区的主应变差（最大剪切应变）的值比周围介质可高出5-6倍。 变形局部化的趋势比声发射率剧增要早得多。     

低硬度橡胶隔震支座基本力学性能及恢复力特性

本研究对低硬度橡胶隔震支座的材料性能（主要包括力学性能）进行了系统的试验开发及理论研究。研究用低硬度橡胶隔震支座包括天然橡胶隔震支座及铅芯橡胶隔震支座两大类18种规格总计近30个大直径隔震支座。研究内容涉及橡胶隔震支座竖向刚度、水平刚度及阻尼等基本力学性能；压缩界限，屈曲及极限剪切变形等界限性能；温度、压力、剪切变形、老化和徐变等相关性及长期特性；同时还对橡胶材料其他性能进行了系统的试验研究。本文主要介绍低硬度天然橡胶隔震支座及铅芯橡胶隔震支座的基本力学性能，如竖向、水平刚度和恢复力等特性。     

高孔隙岩石变形的离散单元模型

实验和野外观测表明颗粒破碎显著影响高孔隙岩石的变形特征.为建立高孔隙岩石变形的数值模型,我们以弹性理论为基础并根据问题的特征进行合理简化,给出了一种颗粒破碎机制,并根据此颗粒破碎条件改进传统的离散单元模型.利用改进的离散单元模型,研究了不同压力条件下高孔隙岩石变形的宏观和微观特征.数值模拟结果表明考虑颗粒破碎的模型能重现高孔隙岩石在不同围压下变形的应力-应变关系、声发射特征、应变局部化和剪切增强压缩等特征.我们还发现,与野外观测结果一致,在高孔隙岩石脆性阶段剪切带内部及附近伴有显著的颗粒破碎.     

低硬度橡胶隔震支座各种相关性及老化徐变特性

作者系统地对低硬度橡胶隔震支座的材料和力学性能进行了试验研究。研究使用的低硬度橡胶隔震支座分18种规格，总计近30个大直径隔震支座。研究内容涉及低硬度橡胶隔震支座的基本力学性能；温度、压力、剪切变形、老化和徐变等相关性；压缩界限，屈曲及极限剪切变形等界限性能以及橡胶材料性能和隔震工程应用等方面。本文主要介绍低硬度橡胶隔震支座的压力、剪切变形、温度对支座刚度、阻尼等力学性能的影响，同时还对隔震支座的老化及徐变特性进行了试验研究，确定低硬度橡胶使用60年后的力学性能变化率。文中同时提出了低硬度橡胶支座的温度修正方程，并提出了隔震结构地震反应分析时支座刚度和屈服荷载变化的取值范围。     

低硬度大直径橡胶隔震支座竖向荷载作用下钢板应力研究

采用大型通用有限元程序,对低硬度大直径橡胶隔震支座在竖向荷载作用下的基本性能进行了精细有限元分析。分析了在竖向荷载作用下支座上下封板、内部钢板的各种应力分布,以及支座顶部是否施加竖向同位移约束、支座孔径比、橡胶材料G值、内部单层橡胶厚度与内部单层钢板厚度之比对支座内钢板受力的影响。结果表明,内部钢板最大Mises应力、最大径向水平正应力约为支座竖向压力的4倍、2.5倍;支座顶部是否施加竖向同位移约束对支座用钢板内力影响较大,特别是支座上封板;橡胶G值的变化对内部钢板受力基本没影响;支座孔径比对靠近孔边缘部分内部钢板应力不均匀性分布影响较大;内部单层橡胶厚度与内部单层钢板厚度的比值对内部钢板的Mises应力、径向正应力、环向正应力影响较大,但对其竖向正应力基本没影响。     

FRP橡胶支座压缩性能分析

将纤维复合材料板(FRP)代替传统板式橡胶支座中的加劲钢板,可以得到一种新型的橡胶支座隔振器,即FRP橡胶支座.文中首先对FRP橡胶支座的概念及特点作了基本介绍,之后,为了了解其在竖向加载情况下的力学性能,为FRP橡胶支座竖向承载力及压缩刚度的设计提供了参考,利用通用有限元程序对FRP橡胶支座进行了有限元数值模拟,对支...     

Analysis of a kinematic self‐centring seismic isolator

This investigation deals with the analytical formulation and experimental validation of a prestressed reinforced concrete seismic isolator with kinematic constraints at both ends. The kinematic isolator was proposed initially as a low‐cost solution for seismic protection of low‐income people housing usually placed at the periphery of big cities where regular to bad soil conditions are common. So, the isolator is also a pile foundation with a central prestressed cable and two rolling steel surfaces at the top and bottom ends. By varying the shapes of the end rolling surfaces, different force–deformation constitutive relationships for the isolator may be obtained. Energy dissipation is introduced by yielding of passive reinforcement at the rolling interphase. Apart from stating the large‐deformation formulation of the element, several relevant aspects of the behaviour of these devices are studied herein, such as the increase in the tension of the central prestressed cable, responsible for the self‐centring action of the isolator, the floor uplift that results from the geometry of the isolator, and the vertical stability of the system. Experimental and theoretical results obtained for a group of 9 testing specimens show an excellent agreement in the force–deformation constitutive relationship. Although not the intent of this article, the device proposed may be extended directly as a coupling beam element for shear wall systems. Copyright © 2006 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

复杂应力条件下饱和松砂单调与循环剪切特性的比较研究

本文利用大连理工大学新引进与开发的“土工静力-动力液压-三轴扭转多功能剪切仪”,针对福建标准砂,在不排水条件下同时进行了单调剪切试验与循环剪切试验,进而对其进行了对比分析。通过比较表明,应力-应变关系的应变软化和硬化特性与流滑变形和循环流动特性密切相关,当循环剪切应力水平高于单调剪切过程中应变软化阶段最小强度时将会发生流滑变形。无论在单调剪切中,还是在循环剪切中,稳定状态时的有效偏应力比随着大主应力方向与竖向之间夹角的增大而减小,在中主应力系数相同的条件下,循环剪切中呈现显著剪胀时的有效偏应力比和最终稳定状态时的有效偏应力比峰值分别与单调剪切中达到相变状态时的有效偏应力比和最终稳定有效偏应力比基本上一致。然而不排水条件下单调与循环剪切过程中孔隙水压力的增长特性却并不相同,循环剪切中的最大孔隙水压力随着初始主应力方向角的增大而减小,单调剪切中的最大孔隙水压力却随着主应力方向角的增大而增大。     

Dynamics of resilient-friction base isolator (R-FBI)

The Resilient-Friction Base Isolator (R-FBI) is composed of a set of flat rings which can slide on each other with a central rubber core and/or peripheral rubber cores. In this base isolator the interfacial friction force acts in parallel with the elastic force in the rubber. It combines the beneficial effect of friction damping with that of the resiliency of rubber. The rubber cores distribute the sliding displacement and velocity along the height of the R-FBI. They do not carry any vertical loads and are not vulcanized to the sliding rings. The system's analytical model and the computer experimental results for both horizontal and vertical components of recorded ground motions and various levels of friction and damping are presented. These results clearly demonstrate the R-FBI's potential as an effective aseismic base isolator.     

Lateral load performance and seismic demand of unbonded scrap tire rubber pad base isolators

The scrap tire rubber pad(STRP) made by natural or synthetic rubber and high strength reinforcing cords exhibits substantial vertical stiffness and horizontal flexibility, and these properties can be regarded as suitable for seismic isolators for structures. The use of environmentally burdensome scrap tires as STRP isolators might be convenient as an efficient and low-cost solution for the implementation of aseismic design philosophy for low-to-medium rise buildings, especially in developing countries. Finite element analyses of unbonded square and strip-shaped STRP isolators subjected to a combination of axial and lateral loads are conducted to investigate its lateral deformation performance under seismic loading. The rubber of the isolator is modelled with Mooney-Rivlin hyperelastic and Prony viscoelastic materials, including the Mullins material damage effect. The influence of the length-to-width ratio and bearing height on the isolator performance is assessed in terms of the force-displacement relationship, horizontal stiffness, damping, and isolation periods. It is shown that the dependence of stiffness on the length-to-width ratio is significant in the longitudinal direction and minor in the transverse direction. The STRP isolators following the proposed design criteria are shown to satisfy the performance requirement at different levels of seismic demand specified by the ASCE/SEI 7-2010 seismic provisions.     

强震蕴育过程中区域垂直形变场多种动态信息演化特征

以区域精密水准重复观测资料为依据,用定性与定量相结合的方法,研究了发生于我国大陆板内的１９９６年丽江７．０级等几次强震过程中区域垂直形变速率、剪切变形率、扩张变形率和体积变化率等形变场多种信息的动态演化特征。结果显示：强震蕴育过程中,区域垂直形变场在空间和时间上均会出现不同程度的非均匀态特征。在此基础上,结合区域构造,进一步研究了判定强震危险区的形变前兆场多种信息异常综合标志,得出了一些用大地形变进行强震预测的初步结论。