Geospatial contour mapping of shear wave velocity for Mumbai city

Shear wave velocity is one of the most important input parameter in the analysis of geotechnical earthquake engineering problems, particularly to estimate site-specific amplification factor and ground response study. Dynamic in situ tests such as spectral analysis of surface waves (SASW) or multichannel analysis of surface waves (MASW) are very expensive. Also due to lack of specialized personnel, these tests are generally avoided in many soil investigation programs. Worldwide, several researchers have developed correlations between the SPT ‘N’ value and shear wave velocity ‘V _s’, which are useful for determining the dynamic soil properties. In the present study, more than 400 numbers of soil borehole data were collected from various geotechnical investigation agencies, government engineering institutes and geotechnical laboratories from different parts of Mumbai city, which is financial capital of India with highest population density. In this paper, an attempt has been made to develop the correlation between the SPT ‘N’ value and shear wave velocity ‘V _s’ for various soil profile of Mumbai city and compared with other existing correlations for different cities in India. Using Geographical Information System (GIS), a geospatial contour map of shear wave velocity profile for Mumbai city is prepared with contour intervals of 25 and 50 m/s. The scarcity of database or maps of shear wave velocity profile for Mumbai city will make the present geospatial contour maps extremely useful and beneficial to the designer, practitioners for seismic hazard study involved in geotechnical earthquake engineering.     

Variations in shear wave velocity and soil site class in Kolkata city using regression and sensitivity analysis

The detrimental effects of an earthquake are strongly influenced by the response of soils subjected to dynamic loading. The behavior of soils under dynamic loading is governed by the dynamic soil properties such as shear wave velocity, damping characteristics and shear modulus. Worldwide, it is a common practice to obtain shear wave velocity (V _s in m/s) using the correlation with field standard penetration test (SPT) N values in the absence of sophisticated dynamic field test data. In this paper, a similar but modified advanced approach has been proposed for a major metro city of eastern India, i.e., Kolkata city (latitudes 22°20′N–23°00′N and longitudes 88°04′E–88°33′E), to obtain shear wave velocity profile and soil site classification using regression and sensitivity analyses. Extensive geotechnical borehole data from 434 boreholes located across 75 sites in the city area of 185 km² and laboratory test data providing information on the thickness of subsoil strata, SPT N values, consistency indices and percentage of fines are collected and analyzed thoroughly. A correlation between shear wave velocity (V _s) and SPT N value for various soil profiles of Kolkata city has been established by using power model of nonlinear regression analysis and compared with existing correlations for other Indian cities. The present correlations, having regression coefficients (R ²) in excess of 0.96, indicated good prediction capability. Sensitivity analysis predicts that significant influence of soil type exists in determining V _s values, for example, typical silty sand shows 30.4 % increase in magnitude of V _s as compared to silt of Kolkata city. Moreover, the soil site classification shows Class D and Class E category of soil that exists typically in Kolkata city as per NEHRP (Recommended provisions for seismic regulations for new buildings and other structures—Part 1: Provisions. Prepared by the Building Seismic Safety Council for the Federal Emergency Management Agency (Report FEMA 450), Washington, DC, 2003) guidelines and thereby highlighting the seismic vulnerability of the city. The results presented in this study can be utilized for seismic microzonation, ground response analysis and hazard assessment for Kolkata city.

     

Use of Surface Waves in Statistical Correlations of Shear Wave Velocity and Penetration Resistance of Chennai Soils

Shear wave velocity (V _s) is one of the most important input parameter to represent the stiffness of the soil layers. It is preferable to measure V _s by in situ wave propagation tests, however it is often not economically feasible to perform the tests at all locations. Hence, a reliable correlation between V _s and standard penetration test blow counts (SPT-N) would be a considerable advantage. This paper presents the development of empirical correlations between V _s and SPT-N value for different categories of soil in Chennai city characterized by complex variation of soil conditions. The extensive shear wave velocity measurement was carried out using Multichannel Analysis of Surface Waves (MASW) technique at the sites where the SPT-N values are available. The bender element test is performed to compare the field MASW test results for clayey soils. The correlations between shear wave velocity and SPT-N with and without energy corrections were developed for three categories of soil: all soils, sand and clay. The proposed correlations between uncorrected and energy corrected SPT-N were compared with regression equations proposed by various other investigators and found that the developed correlations exhibit good prediction performance. The proposed uncorrected and energy corrected SPT-N relationships show a slight variation in the statistical analysis indicating that both the uncorrected and energy corrected correlations can predict shear wave velocity with equal accuracy. It is also found that the soil type has a little effect on these correlations below SPT-N value of about 10.     

Directional properties of small strain shear stiffness in soils

A compiled database of shear wave velocity measurements in a variety of clays, silts and sands shows directional hierarchies between downhole (V_sVH), standard crosshole (V_sHV), and rotary crosshole (V_sHH) tests. The special in situ database has been collected from 33 well-documented geotechnical test sites. Expressions relating the small-strain shear modulus in terms of effective confining stress level, stress history and void ratio are explored for each of these three modes of directional shear wave velocity. The relationships are separated initially into soil groups (intact clays, fissured clays, sands and silts), and then generalised to consider all soil types together.     

Seismic microzonation for Penang using geospatial contour mapping

Shear wave velocity (V _s) and the fundamental site period of the subsurface condition are the primary parameters that affect seismic soil amplification in particular sites. Within the topmost layer of the soil, which measures 30 m, the average shear wave velocity V _s30 is commonly used to build codes for site classification for the design of earthquake-resistant structures and to conduct microzonation studies. In this study, the development of a microzonation map for V _s30 distribution, National Earthquake Hazard Reduction Program V _s30 site classification, and a fundamental site period for Penang are presented. The multichannel analysis of surface wave (MASW) test was conducted for more than 50 sites with available borehole data to develop the microzonation maps. The ten selected V _s profiles measured by MASW show a good correlation with the data obtained using empirical correlations in a previous study. The highest V _s values were identified at the northeastern and southeastern parts of Penang Island, corresponding to the shallow bedrock and the outcrop zone. Conversely, the lowest V _s values were found in the northwestern and southwestern parts of the Penang mainland owing to the thick layer of soft clay and silt deposits. The site period map shows the variation in site periods, with the highest value of 1.03 s at the western part of the Penang mainland and the lowest value of 0.02 s at the eastern part of the Penang Island. The microzonation maps developed in this study are vital to studies on seismic hazard and earthquake mitigation programs in Malaysia.     

Dynamic soil properties for microzonation of Delhi,India

Delhi, the capital of India, has experienced mild seismic shaking during several earthquakes in the past. The large variations of depth to bedrock and ground water table coupled with different soil types at different locations of Delhi necessitate a seismic microzonation study. Dynamic soil properties such as shear wave velocity, modulus reduction and damping characteristics of local soils are the basic and essential input parameters for conducting even a preliminary ground response analysis which is an essential input in microzonation studies. Shear wave velocity is not measured routinely due to its high cost and lack of the required expertise. Several researchers in the past developed correlations between shear wave velocity (V _s ) and routinely measured N values. In the present study, shear wave velocity profiles measured in the field at more than 80 borehole locations to a depth of about 20 to 32m using Spectral Analysis of Surface Waves (SASW) are presented and correlations between shear wave velocity and N values are also presented for use by engineers and designers. Results of strain and stress controlled cyclic triaxial tests on remoulded samples of sand-silt mixtures in the high strain range are used for generating the modulus reduction and damping curves and are compared with the well-known curves in the literature. The results presented in this article can be used for microzonation studies as well as site specific ground response analyses at Delhi.     

Shear wave velocity as function of cone penetration resistance and grain size for Holocene-age uncemented soils: a new perspective

For feasibility studies and preliminary design estimates, field measurements of shear wave velocity, V _s, may not be economically adequate and empirical correlations between V _s and more available penetration measurements such as cone penetration test, CPT, data turn out to be potentially valuable at least for initial evaluation of the small-strain stiffness of soils. These types of correlations between geophysical (Vs) and geotechnical (N-SPT, q _c-CPT) measurements are also of utmost importance where a great precision in the calculation of the deposit response is required such as in liquefaction evaluation or earthquake ground response analyses. In this study, the stress-normalized shear wave velocity V _s1 (in m/s) is defined as statistical functions of the normalized dimensionless resistance, Q _tn-CPT, and the mean effective diameter, D ₅₀ (in mm), using a data set of different uncemented soils of Holocene age accumulated at various sites in North America, Europe, and Asia. The V _s1–Q _tn data exhibit different trends with respect to grain sizes. For soils with mean grain size (D ₅₀) < 0.2 mm, the V _s1/Q _tn ^0.25 ratio undergoes a significant reduction with the increase in D ₅₀ of the soil. This trend is completely reversed with further increase in D ₅₀ (D ₅₀ > 0.2 mm). These results corroborate earlier results that stressed the use of different CPT-based correlations with different soil types, and those emphasized the need to impose particle-size limits on the validity of the majority of available correlations.     

Effect of Fines Type and Content of Sand on Correlation Between Shear Wave Velocity and Liquefaction Resistance

The use of shear wave velocity (V _s) measurements as an in situ test for evaluation of liquefaction potential has increased substantially due to its advantages. Relatively large numbers of studies have been performed to establish the correlation between V _s and liquefaction resistance (CRR) of clean sands. Usually, natural sands contain silt and/or clay, and previous studies have shown that both the amount of fines and their nature influence the values of CRR as well as V _s. Therefore, the CRR–V _s correlations may also be affected by fines content and type of sandy soils. However, effect of fines content and especially fines type of sandy soils on the correlation between V _s and CRR is inadequately addressed in the literature. In this study, cyclic triaxial and bender element tests were conducted on samples of sand containing various amounts of different types of fines, and the effects of fines on the values of CRR and V _s are investigated. The results show that G ₀ and CRR reduce even when small amounts of fines are added to sand. Therefore, use of plasticity index (PI) of the fines fraction is better than the PI of the overall soil when trying to assess the effects of fines. Using obtained experimental data as well as the established semiempirical CRR–V _s relationship, the CRR–V _s correlation was developed for all the tested soils, and the effect of fines type on the correlation is also examined. Based on the results obtained in this study, CRR–V _s correlation is affected by both the amount and the plasticity of the fines present in the sand, and this correlation is soil specific.     

Surface wave studies for shear wave velocity and bedrock depth estimation over basalts

Shear wave velocity (V _S) estimation is of paramount importance in earthquake hazard assessment and other geotechnical/geo engineering studies. In our study, the shear wave velocity was estimated from ground roll using multichannel analysis of surface wave (MASW) technique making use of dispersive characteristics of Rayleigh type surface waves followed by imaging the shallow subsurface basaltic layers in an earthquake-prone region near Jabalpur, India. The reliability of MASW depends on the accurate determination of phase velocities for horizontally traveling fundamental mode Rayleigh waves. Inversion of data from surface waves resulted in a shear wave velocity (V _S) in the range of 200–1,200 m/s covering the top soil to weathering and up to bedrock corresponding to a depth of 10–30 m. The P-wave velocity (V _P) obtained from refraction seismic studies at these locations found to be comparable with V _S at an assumed specific Poisson’s ratio. A pair of selected set of V _S profiles over basalt which did not result in a hazardous situation in an earthquake of moderate magnitude are presented here as a case study; in other words, the shear wave velocity range of more than 200 m/s indicate that the area is highly unlikely prone to liquefaction during a moderate or strong earthquake. The estimated depth to basalt is found to be 10–12 m in both the cases which is also supported by refraction studies.     

An Experimental Characterization of Shear Wave Velocity (V<Subscript>s</Subscript>) in Clean and Hydrocarbon-Contaminated Sand

The characteristics of hydrocarbon-contaminated soils have been among major concerns of geotechnical engineers due to its significant frequency of event and also its influential consequences on our surroundings from various environmental and engineering viewpoints. Heretofore, the effects of diverse kinds of hydrocarbon contaminants on majority of geotechnical properties of fine- and coarse-grained soils such as grain size, hydraulic conductivity, plasticity, compressibility, internal friction, cohesion, and shear strength have been investigated. However, there has not been a concentrated research study examining shear wave velocity (\({\text{V}}_{\text{s}}\)) of hydrocarbon-contaminated soils as an important geotechnical property of soil due to this fact that, in small/very small strain levels, the maximum shear modulus of soils (\({\text{G}}_{ \hbox{max} }\)) can be determined using shear wave velocity (\({\text{G}}_{ \hbox{max} } =\uprho{\text{V}}_{\text{s}}^{2}\)). This paper aims to investigate effects of hydrocarbon contamination on shear wave velocity of sandy soils by comparing shear wave velocities in identically prepared clean and contaminated samples. To this aim, an Iranian light crude oil, a standard type of silica sand (Ottawa sand), and a bender element apparatus were used to minutely measure shear wave velocity of clean and crude oil contaminated sand samples. Moreover, dry and quasi-moist tamping methods were employed in order to provide comparable clean and contaminated specimens (containing 4, 6, 8, 10, and 12 wt% of crude oil), respectively. Firstly, a comprehensive bender element (BE) and resonant column tests were conducted on the identically prepared clean sand samples at various amounts of frequency (2–20 kHz) and under various confining pressure (50–500 kPa) to find the best methods of accurately determining shear wave travel time in BE tests. Thereafter, BE tests were conducted to examine shear wave velocity in contaminated specimens. Based on the results, it was found that there was a critical value for crude oil content with the maximum shear wave velocity so that shear wave velocity of 4 wt% contaminated sand (V_s-4 wt%) was about 1.2 times higher than clean one (V_s-clean), and contrastingly adding further crude oil up to 6 wt% made a significant reduction in value of shear wave velocity to some extent that V_s-6 wt% was slightly lower than V_s-clean (V_s-6 wt% = 0.95–0.97V_s-clean). Moreover, adding more contaminant (8–12 wt%) into sand had negligible influences on shear wave velocity. In this paper, the effects of crude oil contamination on sand microstructure were also evaluated using scanning electron microscopy.     

东帝汶帝力市珊瑚砂地基的工程性质

珊瑚砂属珊瑚礁碎屑土,是一种特殊的地质体,具有典型的疏松多孔、硬度低、易碎的特点,由于珊瑚礁仅分布在热带海域,往往位于远离大陆的礁岛,当前对珊瑚礁岩土的勘察研究较少,相关规范也尚未涉及。以实际工程为对象,对东帝汶某珊瑚砂场地的工程性质进行了一些探讨,从标准贯人试验和钻孔剪切波速试验等原位试验结果进行分析,借鉴了目前石英砂工程性质的评价方法作为对珊瑚砂工程性质判断的参考,对珊瑚砂的强度特性和地震液化特性进行了讨论。相对石英砂的一般性质而言,珊瑚砂的标贯击数较低而相应的剪切波速相对较大,珊瑚砂在地震作用下液化的可能性较大。     

Vp/Vs Anisotropy and Implications for Crustal Composition Identification and Earthquake Prediction

Abstract: The ratio of P- to S-wave velocities (Vp/Vs) is regarded as one of the most diagnostic properties of natural rocks. It has been used as a discriminant of composition for the continental crust and provides valuable constraints on its formation and evolution processes. Furthermore, the spatial and temporal changes in Vp/Vs before and after earthquakes are probably the most promising avenue to understanding the source mechanics and possibly predicting earthquakes. Here we calibrate the variations in Vp/Vs in dry, anisotropic crustal rocks and provide a set of basic information for the interpretation of future seismic data from the Wenchuan earthquake Fault zone Scientific Drilling (WFSD) project and other surveys. Vp/Vs is a constant (Ф0) for an isotropic rock. However, most of crustal rocks are anisotropic due to lattice-preferred orientations of anisotropic minerals (e.g., mica, amphibole, plagioclase and pyroxene) and cracks as well as thin compositional layering. The Vp/Vs ratio of an anisotropic rock measured along a selected pair of propagation-vibration directions is an apparent value (Фij) that is significantly different from the value for its isotropic counterpart (Ф0). The usefulness of apparent Vp/Vs ratios as a diagnostic of crustal composition depends largely on rock seismic anisotropy. A 5% of P- and S-wave velocity anisotropy is sufficient to make it impossible to determine the crustal composition using the conventional criteria (Vp/Vs≤1.756 for felsic rocks, 1.7561.944 fluid-filled porous/fractured or partially molten rocks) if the information about the wave propagation-polarization directions with respect to the tectonic framework is unknown. However, the variations in Vp/Vs measured from borehole seismic experiments can be readily interpreted according to the orientations of the ray path and the polarization of the shear waves with respect to the present-day principal stress directions (i.e., the orientation of cracks) and the frozen fabric (i.e., foliation and lineation).     

上海典型黏土小应变剪切模量现场和室内试验研究

土体小应变剪切模量在基坑、隧道等地下工程的计算分析中有着重要作用,越来越受到人们的关注。虽然上海地区地下工程项目的建设规模不断扩大,但关于上海典型黏土层的小应变剪切模量的研究相对较少。分别采用现场波速测试和室内弯曲元试验对上海典型黏土层的初始剪切模量进行了研究。试验结果表明：在减小土样扰动、保持土样应力状态与原位土体等效的基础上,弯曲元试验得到的初始剪切模量与现场波速测试相一致;考虑了土体应力状态和孔隙比的经验公式能够合理地描述上海典型黏土层初始剪切模量的变化规律,并给出了各土层的经验参数。试验结果可为上海地区地下工程计算分析中小应变剪切模量的估算提供参考。     

Liquefaction Hazard Assessment of Earth Quake Prone Area: a Study Based on Shear Wave Velocity by Multichannel Analysis of Surface Waves (MASW)

The shear wave velocity (V_S) profile based on the dispersive characteristics of fundamental mode of Rayleigh type surface waves indicate underground stiffness change with depth as well as near surface stiffness. The most important utility of shear wave velocity (V_S) is to estimate the liquefaction hazard potential of an area particularly in seismically active region. Rayleigh type surface waves were utilized to estimate the velocity (V_S) of shallow subsurface covering a depth range of 30–50 m employing multichannel analysis of surface waves. The liquefaction hazard map predicts an approximate percentage of an area that will have surface manifestation of liquefaction during an earth quake. The surface wave data acquired in an earth quake prone region of Jabalpur (Seismic zone III), India, yields a velocity (V_S) range of 200–750 m/s corresponding to the subsurface depth of 30–35 m. The results were analyzed for possible liquefaction hazard in the study area and presented here besides the N values.     

Compressional and shear wave velocities at high temperature and confining pressure in basalts from the Faeroe Islands

Compressional (V_P) and shear (V_S) wave velocities and the dependent elastic constants have been determined by the pulse transmission technique to 6 kb confining pressure at room temperature and to 700° C at 6 kb confining pressure for eleven basalts from the Faeroe Islands. The Faeroe basalts investigated are tholeiitic, they clearly lie within the tholeiitic area, and display a pronounced trend of iron enrichment from rocks with an M/M + F ratio of 0.5 to rocks with an M/M + F ratio of about 0.25. The mean V_P and V_S for eleven specimens are 5.57 km/sec and 3.18 km/sec, respectively. Velocity—density relations for the basalts might be more appropriately described by non-linear solutions than by linear relations commonly used for basalts. In general, V_P and V_S remain unaffected by temperature up to 300° C. At higher temperature the changes in wave velocities are influenced by metamorphic processes and are, therefore, somewhat erratic. In zeolite-bearing specimens an abrupt velocity decrease around 350°C is observed, which correlates well with a drastic compaction of bulk volume. Additional experiments on cold-pressed zeolite powder clearly indicate that the sharp velocity decrease in the basalts is related to dehydration of zeolite minerals. Partial-melting processes, which occur within vesicules and pore-spaces at distinctly higher temperatures have no additional effect on wave velocity. Comparison with field data reveals that, without exception, the velocities at 0.5 kb confining pressure display the same range that has been commonly noted in refraction data for Layer 2. There are no significant differences in wave velocities and the pressure—temperature dependence in samples recovered from the upper, middle, and lower basalt series in the Faeroe Islands.     

砂的物理力学性质与声速的关系

本文叙述了不同粒径的石英砂粒的物理力学特性与声速关系的室内试验研究,着重探讨了容重、含水量与纵波波速、横波波速之间的关系,给出了以含水量为参数的容重与纵横波速度间的关系式,以及空隙比与纵横波速度之间的关系式。此外分析了在各种不同含水量时,容重、空隙比与波速的单调变化关系,并给出了相应的表达式。     

Relations between Sound Wave Velocities and Physical Properties of Quartz Sands

The correlations of sound wave velocities and physical properties of quartz sand with different grain size were investigated through laboratory tests. Emphases were put on studying the relationship between density, water content and longitudinal and shear wave velocities. The equations which show the correlation of density, void ratio and longitudinal and shear wave velocities, and with water content as a parameter are given in this paper. In addition, the monotonic relations of density, void ratio and sound wave velocities for sands with different water content are also presented.     

Pile Head Cyclic Lateral Loading of Single Pile

This paper presents an elastic continuum model using an extended nonlinear Davies and Budhu equations, which enables the nonlinear behavior of the soil around the long elastic pile to be modeled using a simple expression of pile-head stiffness method. The calculated results were validated with the measured full-scale dynamic field tests data conducted in Auckland residual clay. An idealized soil profile and soil stiffness under small strain (i.e. shear modulus, G _s and shear wave velocity, V _s of the soil) determined from in situ testing was used to model the single pile tests results. The predictions of these extended equations are also confirmed by using the three-dimensional finite-element OpenSeesPL (Lu et al. in OpenSeesPL 3D lateral pile-ground interaction: user manual, University of California, San Diego, 2010). A soil stiffness reduction factor, G _s /G _s,max of 0.36 was introduced to the proposed method and model. It was found to give a reasonable prediction for a single pile subjected to dynamic lateral loading. The reduction in soil stiffness found from the experiment arises from the cumulative effects of pile–soil separation as well as a change in the soil properties subjected to cyclic load. In summary, if the proposed method and model are accurately verified and properly used, then they are capable of producing realistic predictions. Both models provide good modelling tools to replicate the full-scale dynamic test results.     

Undrained Shear Strength in Cohesive Soils Estimated by Directional Modes of In-Situ Shear Wave Velocity

The estimated undrained shear strength (s_u) is often not a unique value because it can be evaluated by various test types and/or procedures, such as different failure modes, shear strain rates, and boundary conditions. This study explores (1) the relationship between reference undrained shear strength and in situ shear wave velocity in terms of the effective overburden stress, and (2) the independent relationships to evaluate the undrained shear strength with special consideration of different directional and polarization modes (VH, HV, HH shear waves), which has not been reported. This evaluation is done via a worldwide database compiled from 43 well-documented geotechnical test sites associated with soft ground. Finally, new correlation models are proposed to estimate the undrained shear strength based on the in situ shear wave velocity as well as the plasticity index or the overconsolidation ratio. The application of the shear wave velocity–undrained shear strength relation is illustrated through two independent case studies. The proposed relationships are expected to contribute to reasonable estimates of undrained shear strength as well as offer practical guidance on even extrapolation beyond the data that is available to geotechnical engineers.     

上海地区土体抗剪强度与静力触探比贯入阻力相关关系研究

基于上海地区19个工程共201组数据,通过黏土、粉质黏土和粉砂在上海地区土层中的分布,比贯入阻力Ps,室内固结快剪试验黏聚力cu和摩擦角?u,孔隙比e,塑性指数Ip沿土层深度的变化,分析得到3种土类的抗剪强度与比贯入阻力的相关关系,并总结了国内软土地区土体抗剪强度与静力触探比贯入阻力之间的相关关系。本文得到黏土的相关关系与以往的经验公式相近,同时给出了原位土层粉质黏土和粉砂的相关关系。区别不同土类使得相关关系可用性提高,在工程应用中更加合理。根据本文相关关系,通过静力触探比贯入阻力可以得到不同土层的抗剪强度值,进而应用于基坑稳定计算。本文研究的结果可以应用于海相沉积土的勘察和工程设计工作。