高孔隙性软弱砂岩在一般三轴应力状态下的力学特性

本文作者利用茂木清夫教授的岩石真三轴压缩仪,研究了抗压强度为300公斤/匣米2左右,孔隙度高选27%,容重仅为1.85克/厘米3的高孔隙性软弱砂岩的力学特性.在室温下,把围压加到500公斤/厘米2,就观测到变形和破坏特性,从脆性过渡到韧性的全过程.同时,分别在50和100公斤/厘米2的恒定围压下,成功地把中间主应力σ2从σ2=σ3的下限加到σ2=σ1的上限,观测到强度随中间主应力的增长而连渐增加到最大值后又逐渐下降的全过程;在100公斤/厘米2的恒定围压下以及σ3=100,σ2=295公斤/厘米2的一般三轴应力状态下。     

一般三轴压缩下岩石的流动和破坏

引言在天然条件下,岩石的破坏和流动是在复杂的组合应力下产生的.应力状态的影响在岩石力学里是个基本课题之一.为了研究这一影响,在各种组合应力状态下,进行了许多岩石变形的室内实验。     

FLOW AND FRACTURE OF ROCKS UNDER GENERAL TRIAXIAL COMPRESSION

Recent laboratory studies of the flow and fracture of rocks under general triaxial compression are reviewed .New Developments in laboratory techniques have made it possible to measure three principal stresses and strains under general triaxial stress states ,in which all three principal stresses are different . Strength and ductility of isotropic rocks are markedly affected not only by the least compression σ3 ,although these two effects are rather additional in strength ,but opposite in ductility .The experimental results show that dilatancy is highly anisotropic rocks have been also measured under the general triaxial compression .In this case ,the effect of the intermediate compression markedly depends on the orientations of the weak planes.     

岩体裂隙三轴应力渗透规律的试验研究

利用三轴应力渗透仪分别对煤矿底板的硬岩和软岩进行三轴应力渗透试验 ,观测渗水量、围压、轴压及水压的变化。     

高应力下砾质心墙料切线模量研究

使用高压大型三轴仪,对某300 m级土石坝的砾质土心墙料进行了最高围压5 MPa的三轴试验。试验结果表明砾质土的应力-应变关系符合双曲线关系,抗剪强度包络线呈非线性。根据参数的物理意义,初始模量Ei应在尽可能小的应变范围内取值,最大主应力差 应在大应变范围内取值,且实际工程的应变在1 %左右,建议在?a= 0 %～3 %下取Ei值,在?a = 5 %～15 %下取 值,数据拟合表明建议取值法比传统取值法拟合度高。由于试验的围压范围较大,提出把围压分0.2～1.0 MPa,1.5～3.0 MPa,3.5～5.0 MPa三段分别取切线模量,通过回归证明拟合较好。     

Considerations on strength of intact sedimentary rocks

This study presents the results of laboratory testing of sedimentary rocks under point loading as well as in uniaxial and triaxial compression. From the statistical analysis of the data, different conversion factors relating uniaxial compressive and point loading strength were determined for soft to strong rocks. Additionally, the material constant m_i, an input parameter for the Hoek and Brown failure criterion, was also estimated for different limestone samples by analysing the results from a series of triaxial compression tests under different confining pressures. The uniaxial compressive strength (UCS) of intact rocks, as estimated from the point load index using conversion factors, together with the Hoek–Brown constant m_i, and the Geological Strength Index (GSI) constitute the parameters for the calculation of the strength and deformability of rock masses.     

Influence of Loading Rate on Deformability and Compressive Strength of Three Thai Sandstones

Uniaxial and triaxial compressive strength tests have been performed using a polyaxial load frame to assess the influence of loading rate on the strength and deformability of three Thai sandstones. The applied axial stresses are controlled at constant rates of 0.001, 0.01, 0.1, 1.0 and 10 MPa/s. The confining pressures are maintained constant at 0, 3, 7 and 12 MPa. The sandstone strengths and elastic moduli tend to increase exponentially with the loading rates. The effects seem to be independent of the confining pressures. An empirical loading rate dependent formulation of both deformability and shear strength is developed for the elastic and isotropic rocks. It is based on the assumption of constant distortional strain energy of the rock at failure under a given mean normal stress. The proposed multiaxial criterion well describes the sandstone strengths within the range of the loading rates used here. It seems reasonable that the derived loading rate dependent equations for deformability and shear strength are transferable to similar brittle isotropic intact rocks.     

Q3砂黄土真三轴强度变形特性研究

为了研究Q3砂黄土强度变形特性,以甘肃永靖黑方台Q3砂黄土为研究对象,利用西安理工大学研制的真三轴仪,进行了3个围压（50、100 kPa 和200 kPa）、3个b值（0、0.25和0.5）和3个含水率（5%、10%和15%）不同工况试样破坏情况的真三轴试验。试验结果发现：（1）真三轴条件下Q3砂黄土剪切破坏方式以侧胀破坏、单缝剪切破坏为主,其次少数土样发生锥形破坏、双缝剪切破坏和T型缝剪切破坏。（2）相同围压和含水率、不同中主应力比（b）的情况下,Q3砂黄土的主应力差随中主应力比增大而增大,应力-应变关系曲线为强硬化型,剪胀现象明显;中主应力比对广义剪应力和广义剪应变之间关系有一定影响,随b值增加,曲线依次增加;随b值的增加,强度降低,广义剪应力与平均球应力比（q/p）与主应变关系曲线逐渐变缓,且曲线依次降低。（3）随含水率增加,Q3砂黄土由固态向半固态转化过程中,不同中主应力比时黏聚力均出现明显降低,但内摩擦角则出现微小增加。     

Effect of fluid pressure on rock compressive failure in a nearly impermeable crystalline rock: Implication on mechanism of borehole breakouts

We conducted laboratory true triaxial experiments in the nearly impermeable Pohang rhyolite to investigate failure mechanisms under ‘dry’ and ‘wet’ rock conditions. Under ‘dry’ conditions prismatic specimens were jacketed all around to prevent confining fluid penetration. Under ‘wet’ conditions one pair of the specimen faces was left unjacketed and in direct contact with the confining fluid (kerosene) applying the least principal stress in an attempt to simulate the case of an unlined borehole wall. In both testing setups the true triaxial compressive strength for a given least principal stress increases significantly as the intermediate principal stress rises. The unjacketed rhyolite strength is, however, only 60 to 85% of the strength under dry conditions, depending on the magnitude of the intermediate principal stress. In dry rhyolite the failure process begins upon dilatancy onset, followed by microcrack localization, and ending in a steeply dipping shear fracture. On the other hand, brittle fracture in wet specimens occurs almost immediately after the onset of dilatancy by the development of one or more through-going extensile fractures subparallel and adjacent to one of the unjacketed faces, resembling the extensile cracks leading to borehole breakouts in crystalline rocks. We infer that upon dilatancy the confining fluid intrudes and quickly propagates newly opened stress-induced microcracks subparallel to the unjacketed faces, leading to ‘early’ failure.     

锦屏二级水电站大理岩复杂加卸载应力路径力学特性研究

地下洞室开挖围岩经历典型径向卸载、环向加载应力路径,由此引起的岩体强度、变形特征和破坏机制也不尽相同。针对锦屏二级水电站高地应力赋存环境,对施工排水洞大理岩开展常规单轴全应变、三轴压缩、卸围压、卸围压-加载轴压等4种不同应力路径力学试验,得到应力-应变全过程曲线、变形破坏特征和极限储能变化规律。试验研究结果表明, （1）锦屏二级水电站大理岩破坏时轴向应变一般较小,为硬脆性材料,卸荷应力路径下该脆性特征更为明显;（2）卸围压同时加载轴压试验峰值强度对应轴向应变、环向应变及体积应变值一般高于单纯的卸围压值,而对应峰值强度则一般低于卸围压值;（3）卸荷速率较大时,变形模量越大,大理岩峰值强度越低。加载速率越大,变形模量越小,峰值强度越高。初始围压越高,变形模量值越低,峰值强度越高;（4）无侧限作用时试件主要为张拉破坏,低侧限作用时为剪切破坏为主,局部存在张拉破坏,较高侧限时,剪切面为典型X或Y型;（5）岩石试件具有极限储能值,该值受多种因素的影响。一般情况下试件破坏对应围压越高,极限储能值越高,卸载速率越大,极限储能值越小。研究结果对于岩爆孕育发生机制解释以及工程实际问题的解决均有参考价值。     

Intelligent prediction of the stress–strain response of intact and jointed rocks

An application of Artificial Neural Networks for predicting the stress–strain response of jointed rocks under different confining pressures is presented in this paper. Rocks of different compressive strength with different joint properties (frequency, orientation and strength of joints) are considered in this study. The database for training the neural network is formed from the results of triaxial compression tests on different intact and jointed rocks with different joint properties tested at different confining pressures reported by various researchers in the literature. The network was trained using a three-layered network with the feed-forward back propagation algorithm. About 85% of the data was used for training and the remaining 15% was used for testing the network. Results from the analyses demonstrated that the neural network approach is effective in capturing the stress–strain behaviour of intact rocks and the complex stress–strain behaviour of jointed rocks. A single neural network is demonstrated to be capable of predicting the stress–strain response of different jointed rocks, whose intact strength varies from 11.32 MPa to 123 MPa, spacing of joints varies from 10 cm to 100 cm, and confining pressures range from 0 to 13.8 MPa.     

盐岩三轴卸荷力学特性试验研究

结合金坛地下盐穴储气库工程,以腔体围岩实际受力状态为研究依据,进行了盐岩卸围压力学特性试验,得到了盐岩卸围压过程的应力-应变关系、变形特征及其规律。试验结果表明,在卸围压初始阶段,试样的轴向和径向应变增加相对缓慢,且应变值和围压基本呈线性,随着围压继续降低,轴向与径向应变值急剧增加;卸载曲线与加载曲线相比,在最大主应力 相等的条件下,当卸载围压达到与常规三轴压缩围压相对应值时,对应的轴向和径向应变值较三轴压缩时应变值要大,表明卸荷试验能引起试样更大的变形,卸荷产生的扩容量比加载时扩容量更大,更容易导致试样变形破坏;盐岩卸围压表现为塑性变形特征,与其他硬岩卸围压属脆性破坏有较大区别。研究结果对盐穴储气库工程的稳定性评价和注采气过程具有一定的指导意义和参考价值。     

三轴应力状态下盐岩强度分析探讨

通过分析盐岩在三轴应力状态下的变形,说明了较高围压下盐岩的大变形特性,提出了三轴应力状态下,利用轴向荷载除以试件初始横截面面积得到应力-应变关系存在的问题,据此对工程应变和对数应变进行了分析和对比,阐明了这两种应变的适用条件,并开展了不同围压下的试验测试和对试验结果对比分析。研究揭示了应利用对数应变分析盐岩的大变形特性和对变形后的应力进行修正,得到了盐岩的工程应变和对数应变均可表示为围压的线性函数,围压为20 MPa时的轴向压缩变形量是5 MPa时的3.09倍。围压越高,对数应变修正得到的最大轴向应力与不修正的差值越大,用对数应变修正后的轴向应力低于不修正的结果,围压达到20 MPa时,前者仅为后者的63.85%。     

围压路径对冻结粉质砂土变形行为及强度的影响研究

目前关于冻土的室内三轴压缩试验研究多采用恒围压下的轴向加载方法,而实际工程中的受压土体基本处于围压、轴压同时发生变化的情况。以冻结粉质砂土为研究对象,进行了变围压和恒围压下的三轴剪切测试。根据试后试样变形情况,给出了试样面积的统一修正公式,研究结果表明：当含水量较小时,围压路径对应力-应变曲线的初始段和最终段没有显见影响,但在应力-应变曲线中间段,变围压下的应力-应变曲线明显在相应的恒围压曲线之下,且初始围压越小,曲线位置越低。当含水量不低于饱和值时,围压路径和含冰量共同影响着应力-应变曲线的发展趋势,且变围压曲线的最终段基本都在相应的恒围压曲线之上,中间段变化特点与含冰量和初始围压有关。围压路径对强度随围压变化趋势的影响跟含水量大小有关。当含水量较小时,两种围压路径下的强度值比较接近;当含水量不低于饱和值时,恒围压下的强度值低于相应变围压下的强度值。     

The Various Stress Paths Causing Deformation and Failure in Rocks

The rock deformation and failure tests are performed along various stress paths under true triaxial stress state. The experimental results have shown that the change of three principal stresses (the increase of the maximum principal stress, the decrease of the minimum principal stress, the decrease of the confining pressure and the increase or decrease of the intermediate principal stress ) can lead to deformation and failure in rocks. The strength, the deformability and the failure precursors of rocks are related with stress paths. Based on the results of the study, the problems of the stress path in rock engineering are discussed.     

岩体变形和破坏的各种应力途径

在真三轴应力状态下进行了各种应力途径的岩石变形和破坏实验。实验表明,三个主应力的变化(最大主应力的增加,最小主应力的减小,围压的减小以及中间主应力的增加或减小)都能引起岩石变形和破坏。而且岩石的强度、延性和脆性、体积变化和破坏前兆等都与应力途径有关。据根试验结果探讨了岩体工程中的应力途径问题。     

考虑中主应力变化的原状黄土变形特性研究

为研究在高围压条件下考虑中主应力变化的原状黄土变形特性,利用西安理工大学真三轴仪对原状黄土进行了控制固结围压和中主应力b值的等b等p(p为球应力)剪切试验,试验给出了高围压条件下各主应变之间的关系,得到了不同高围压条件下的破坏应变与不同b值阶段的影响规律。结果表明：高围压条件下,所有b值阶段的ε₃均为膨胀变形;b=0.2为中主应变变形临界点,0≤b<0.2为中主应变膨胀变形,0.22)、小主应变的b值敏感度K(ε₃)和广义应变的b值敏感度K(ε_s)在b值为0～0.7之间均增长,0.7～0.9之间受b值变化影响减弱,0.9～1.0受b值变化影响最大。K(ε_v)基本在0～5范围内,说明在不同中主应力阶段破坏体应变受b值变化的影响程度较小。     

The effects of intermediate principle stress on the mechanical behavior of transversely isotropic rocks: Insights from DEM simulations

The discrete element method (DEM) is used to study the response of anisotropic rocks under true triaxial testing. Numerical samples of seven different bedding orientations (β = 0^o, 15^o, 30^o, 45^o, 60^o, 75^o, and 90^o) are created. Six series of test simulations (σ₃ = 0, 10, 30, 50, 70, and 100 MPa) are conducted on each sample, with five different σ₂ values, varied from σ₃ to σ₁. The effects of anisotropy and intermediate stress on the peak strength, brittle-ductile transition, and degree of anisotropy are subsequently explained through underlying micromechanics. Results show a “fan-shaped” variation of the peak strength with σ₂, displaying an ascending-then-descending trend. An increasing brittleness with σ₂ is observed at lower confining pressures for all, but medium anisotropy angles. For higher confining pressures, increasing ductility with σ₂ is seen for every anisotropy angle. A U-shaped variation of peak strength with anisotropy angles is noted that flattens under high intermediate stress. Hence, for numerical models of Posidonia shale under normalized σ₂ higher than 0.76, the anisotropy effect is found to be negligible. Micromechanical analyses reveal that the stress asymmetry, suppression of weak plane action as well as the localization and coalescence of microcracks in the intact rock matrix, due to σ₂, are the contributors towards the obtained trends. Since existing failure criteria do not weigh in these features in geotechnical assessments, this paper helps future studies by providing a deeper understanding of these effects and a comprehensive data set for the analyses of anisotropic rocks under polyaxial stress conditions.     

高温作用后花岗岩三轴压缩试验研究

为综合考察温度、围压对花岗岩力学性质及破坏方式的影响,在高温（25℃～1 000 ℃）作用后,利用MTS815.02电液伺服材料试验系统对花岗岩岩样进行不同围压作用下的三轴压缩试验。研究结果表明,（1）围压一定时,经历不同高温作用后花岗岩三轴压缩全应力-应变曲线经历了压密、弹性、屈服、破坏、塑性流动5个阶段;（2）经历不同高温作用后岩样三轴抗压强度与围压呈非线性二次多项式增长关系,围压为40 MPa时的抗压强度比单轴抗压强度提高了382.30%;常规三轴压缩条件下,400 ℃是花岗岩力学参数的阀值温度;（3）经历高温作用后,岩样弹性模量随围压升高呈增大趋势,围压为40 MPa时的弹性模量比单轴时提高了90.26%;随温度升高呈二次非线性减小,1 000 ℃时的弹性模量比25℃时降低了57.16%;（4）花岗岩的失稳型式同时取决于围压和温度。单轴压缩状态下,随着温度的升高,岩样变形破坏型式由脆性破裂向塑性变形过渡,失稳型式在低温时为突发失稳、中高温为准突发失稳,温度高于800 ℃为渐进破坏;三轴压缩状态下,随着围压的增大,岩样破裂型式由脆性张拉破裂逐渐向剪切破裂过渡,岩样的失稳型式以突发失稳为主。在试验温压范围内,影响花岗岩力学性质的首要因素是温度,其次是围压。     

三轴应力下不同粒径破碎砂岩渗透特性试验

地下工程中破碎岩体往往处于三向应力状态,此类岩体具有孔隙率大、渗透性高等特点,在地应力与高水头作用下易发生渗流失稳破坏,诱发突水灾害。为研究三轴应力下破碎砂岩的渗透特性,运用自主研发的破碎岩石三轴渗流试验系统,采用稳态渗透法进行5种粒径破碎砂岩的渗流试验,得到了三轴应力下破碎砂岩渗透特性变化规律,推导了有效应力与渗流速度之间的关系。试验结果表明：三轴应力下破碎砂岩的有效应力与渗流速度呈线性关系,且轴向位移越大时,随有效应力的增加渗流速度减小的幅度越小;三轴应力下5种粒径破碎砂岩的孔压梯度与渗流速度服从Forchheimer关系,两者之间的相关系数达0.95以上;轴向位移恒定时,随着围压的增大,破碎砂岩渗透率k减小,非Darcy流β因子增大,各级轴向位移下,破碎砂岩的渗透率与围压之间呈指数函数关系;随着孔隙率的减小,5种粒径的破碎砂岩渗透率呈减小趋势,非Darcy流β因子整体增大,且渗透率量级为10-14～10-11 m2,非Darcy流β因子的量级为106～1012 m-1。