单自由度圆柱涡激振动特性及其影响因素分析

对二维刚性圆柱涡激振动进行了系统理论和数值模拟研究,对比了不同因素下圆柱振幅、锁定区间、升阻力系数等关键参数和特征,探究了影响圆柱涡激振动特性的因素。通过线性化分析推导出了锁定区间柱体响应的频率比、振幅与流体荷载和系统物性参数之间的定性关系。为检验理论分析结果,对相关经典实验的结果进行了整理,并用RANS模型开展了相应的数值模拟。理论分析、实验和数值模拟三者的结论相符,可以确认以下结论:当圆柱处在锁定状态时,其振幅大小由组合因子决定。组合因子越小,圆柱的振幅越大,反之则越小,但是组合因子对振幅的影响幅度有限;柱体锁定区间范围的大小由质量比决定,质量比越小,锁定范围越大,反之则越小,质量比对锁定区间范围的大小有显著影响,影响的主要范围是在约化速度较大一端。     

二维圆柱涡激振动数值模拟中湍流模式适用性的探讨

采用RANS结合4种湍流模型对低质量比单自由度涡激振动进行数值模拟,对比分析其对该问题的适用性。用四阶Runge-Kutta法离散运动方程,基于动网格技术处理圆柱振荡引起的网格运动,并对壁面条件的处理进行了细致分析。根据Williamson水槽实验,从振幅比、频率比响应、水动力系数及相位突变、尾涡模式等方面对比分析了4种模型的性能和表现,结果表明Standardκ-ω模型与实验差异较大;目前本类研究中运用较少的Realizableκ-ε模型也是可以适用于涡激振动计算的;κ-ω系列模型得到的最大振幅(0.55D)小于κ-ε系列模型的结果(0.87D);SSTκ-ω模型以及2种κ-ε模型都反映出锁定区振动频率fex与泄涡频率fst分离,其中SSTκ-ω模型较为接近实验结果;尾涡模式上,SSTκ-ω模型在各个分支与实验结果一致;总之,各种模型针对不同物理现象各有优势和缺陷。     

低雷诺数下圆柱强迫振动特性光滑粒子流体动力学模拟

基于光滑粒子流体动力学(SPH)方法,开发了能够准确描述水流作用下圆柱强迫振动特性的数学模型。通过引入适合于无网格粒子法的开边界算法,来模拟出入流边界条件,建立了具有造流功能的SPH数值水槽。圆柱及计算域的上下边界均采用修正的动力边界条件进行模拟。借助于粒子位移矫正和压力修正算法,避免了圆柱周围流体粒子压力大幅震荡以及结构下游区域出现空腔等非物理性现象。使用典型的圆柱绕流数据,验证了所建SPH模型的计算性能,研究了固定圆柱在低雷诺数情况下的尾涡脱落模式和升阻力变化规律。明确了低雷诺数下强迫振动圆柱在频率锁定以及非锁定区间内的升力变化规律,量化了升力与外界激励频率之间的关系。     

分离盘控制圆柱涡激振动的数值模拟研究

圆柱涡激振动问题一直以来备受关注,分离盘作为涡激振动抑制装置得到广泛研究。分离盘长度L与圆柱直径D之比L/D是影响抑制效果的主要因素。运用有限体积法结合RANS方程与一定的湍流模式离散和求解流场,通过编写自定义程序,使用动网格模拟结构物的运动带来的流域边界的变化,针对弹性支撑的圆柱及附加长度为0.5 D的分离盘模型,在约化速度Ur为2.5~13的情况下,对涡激振动及其抑制进行研究。结果表明:分离盘可以抑制甚至消除圆柱涡激振动,99%以上的振幅被抑制;锁定区始点被推后,锁定区变窄;附加分离盘的圆柱阻力和升力被抑制;其斯特鲁哈数(St)稍高于单圆柱St但差别不大。     

低雷诺数下圆柱涡激振动的二维有限元数值模拟

采用有限元方法求解原始变量的二维不可压粘性流体的N-S方程,计算了雷诺数从90到150范围内圆柱绕流引起的涡激振动,完整地再现了流固耦合系统从不共振到频率锁定,再到脱离锁定的过程,成功地预测到了涡激振动的“拍”和“锁定”现象,并与A nagnostopou los和B earam an的试验结果进行了比较。计算涡激振动时用ALE方法分析圆柱和流体的耦合作用,圆柱振动被简化为质量-弹簧-阻尼系统。     

质量比对柔性立管涡激振动影响实验研究

质量比是影响海洋立管涡激振动的一个重要因素.通过在室内物理实验中使立管模型内部分别充填空气、水和沙来改变立管的质量比,从而研究质量比对柔性细长立管涡激振动的影响.实验结果表明:在相同流速下,质量比大的立管模型所激起的模态更高.在低约化速度区域,空管和水管的涡激振动响应频率与涡脱落频率相同,沙管的响应频率则与自振频率更接近,三种质量比立管的响应位移较接近;在高约化速度区域,三种质量比的立管模型的响应频率处于自振频率和涡脱落频率之间,但空管的响应频率随约化速度的增大而不断增大,同一流速下,质量比大的立管模型响应位移小,其中空管的涡激振动响应一直处于大振幅的锁定状态下.共振区域对应约化速度的范围随着质量比增大而减小.     

不同排列方式和间隙比下双圆柱流致振动特性研究

采用基于ALE的流固耦合分析方法,将圆柱体振动模型简化为平面双自由度质量-弹簧-阻尼系统,进行了计算参数无关性分析。对不同θ角和间隙比T下的双圆柱流致振动进行数值模拟,并与单圆柱振动计算结果进行比较,得到了不同θ角和间隙比T下中心圆柱的升阻力系数、流场分布和运动轨迹变化情况。通过分析发现小间隙比下由于两圆柱间的相互干扰,改变了中心圆柱的尾涡结构,导致了升力和阻力系数随不同θ角而发生变化;小间隙比下由于两圆柱间的相互干扰影响,均使中心圆柱的轨迹在不同θ角下发生了较大的变化,顺流向的振动频率与单圆柱振动时相比出现了多倍频,导致其运动轨迹发生了变化。     

并列双圆柱涡激振动的经验性模型研究

建立一种新的预报并列双圆柱涡激振动响应的经验性模型,根据特定间距比条件下旋涡脱落频率出现分支的现象,提出以两个具有不同固有频率的尾流振子来共同描述结构的近壁尾涡动力特性,同时两个振子均满足van der Pol方程,进而得到结构振子和流体振子的耦合方程组。使用该模型分别对中高质量比和低质量比的并列圆柱涡激振动问题进行数值计算,结果表明,结构的位移响应和最大振动幅值等变化规律与实验结果趋势一致,数值基本吻合。     

圆柱涡激振动研究进展与展望

圆柱涡激振动广泛存在于机械工程、海洋工程等诸多领域,研究者们取得了许多研究成果,而系统综述圆柱涡激振动的论文距今已近10 a,因此,有必要对近10 a的研究进展进行系统分析。文中系统地总结了近10 a圆柱涡激振动研究成果,阐述了圆柱涡激振动的尾流模态和其对应的响应分支之间的因果关系,分析了影响圆柱涡激振动的关键因素(如质量比、阻尼比和雷诺数)对涡激振动响应的影响,介绍了圆柱涡激振动最大响应振幅的曲线拟合公式及其局限性,最后对圆柱涡激振动的研究方向提出建议。     

振荡流绕圆柱流动的离散涡模拟

本文采用逐级近似法解边界层方程,由此来确定有涡存在情况下,绕圆柱振荡流动的分离点.与离散涡模拟法相结合,本文计算了分离点随时间变化的规律和圆柱的受力.给出了高雷诺数下圆柱的阻力系数C_D、惯性力系数C_M及升力系数C_L(t)的均方根值(r.m.s.).计算结果与他人的实验结果符合较好.     

Vortex dynamics of a fluid near a boundary with a circular cavity

The motion of a point vortex along a rectilinear boundary with a circle cavity, which models the coastline of a bay, and associated fluid particle advection are studied within a model of barotropic inviscid fluid. Using an analytical expression for the complex potential through which the velocity field is determined, we show that fluid particles start moving irregularly when the vortex is passing the cavity due to the nonstationarity of the velocity field generated by the vortex. Some of the fluid particles which were initially inside the vortex atmosphere leave it due to the irregularity and remain within the cavity vicinity. Depending on the initial position of the vortex and a parameter that determines the cavity size, the fraction of these fluid particles can differ significantly from fluid particles initially uniformly distributed within the vortex atmosphere. The escape of fluid particles from the vortex atmosphere is shown to be most efficient in the case of a relatively closed cavity under the condition that the initial vortex atmosphere area should be significantly smaller than the cavity area.     

Long period waves at a mouth of a bay in a basin

By a model bay with a mouth and a narrow, an experiment on long period waves is carried out to discuss the behavior of the tsunamis and storm surges. Emphasis is placed on the analysis of the characteristics of the current velocities associated with the long period waves incoming through the mouth in terms of Ursell's parameter.     

Response of a thin plate resting on a fluid-layer to a moving point load

This paper is concerned with the vibrations of a thin plate resting on a fluid-layer subjected to a moving point force. The frequency is assumed to be low and the fluid is deep. Both the fluid and the point force are always in contact with the plate. Hankel Transform and complex integration techniques are used to calculate the lateral displacements withrespect to a moving coordinate system and a coordinate transformation is used to achieve the results with respect to a fixed point. Numerical results are discussed with respect to the velocity of the moving force, its direction of movement and the fluid depth.     

Comparison between a U-OWC and a conventional OWC

With an additional vertical duct at the wave-beaten side, an OWC is expected to give some much better performances. This is, essentially, due to two reasons. First, an OWC with the additional vertical duct (U-OWC) has an eigenperiod greater than the eigenperiod of a conventional OWC. Second, the amplitude of the pressure fluctuations on the opening of a U-OWC is greater than the amplitude of the pressure fluctuations on the opening of a conventional OWC (the greater the smaller the wave period is). For the first reason, a U-OWC can give performances better than those of a conventional OWC both with swells and large wind waves. For the second reason, a U-OWC can give performances better than those of a conventional OWC also with small wind waves.     

Wave motion over a breakwater system of a horizontal plate and a vertical porous wall

A two-dimensional analytical solution is presented to study the reflection and transmission of linear water waves propagating past a submerged horizontal plate and through a vertical porous wall. The velocity potential in each fluid domain is formulated using three sets of orthogonal eigenfunctions and the unknown coefficients are determined from the matching conditions. Wave elevations and hydrodynamic forces acting on the porous wall are computed. Reflection and transmission coefficients are presented to examine the performance of the breakwater system. The present analytical solutions are found in fairly good agreement with the available laboratory data. The results indicate that the plate length, the porous-effect, the gap between plate and porous wall, and the submerged depth of the plate all show a significant influence on the reflected and transmitted wave fields. It is also interesting to note that the submerged plate plays an important role in reducing the transmitted wave height, especially for long incident waves.     

Frictionless Generation of a Tidal Eulerian Residual Flow over a Sill in a Narrow Channel

Using a vertically two-dimensional, two-layer model, we have analytically examined the generation mechanism of a nonzero Eulerian residual flow by strong tide-topography interaction in a narrow channel where the frictional effect is not included. In this case, tidally generated baroclinic disturbances are forced non-uniformly in space and time while being advected by a strong tidal flow over the non-uniform slope of the bottom topography. Consequently, nonzero Eulerian residual flow results when averaged over one tidal period. Although the time average of the velocity field is thus nonzero, the associated Eulerian residual transport in each layer is compensated by a Stokes transport so that no Lagrangian residual transport results in both layers. This warns us that simple time averaging of the velocity data obtained at a fixed mooring station might lead to a spurious material transport. This revised version was published online in August 2006 with corrections to the Cover Date.     

Run-Up of a Nonlinear Monochromatic Wave on a Plane Beach in Presence of a Tide

Oceanology - Abstract—The nonlinear problem of run-up of a long wave on a plane beach in presence of a tide is solved within nonlinear shallow water theory using the Carrier–Greenspan...     

数据稀缺生态系统中多种类质量谱模型的构建

多种类生态模型已经被广泛应用于渔业活动影响应预测和管理措施效果评估。质量谱模型是一种基于生理过程构建的生态模型,该模型为描述鱼类群落在个体摄食变异和随个体发生的生态位迁移提供了一个可行的方法。尽管生态模型在增进生态系统认识上具有重要意义,其应用在数据稀缺的渔业中受到很大限制。作为实践基于生态系统渔业管理(EBFM)的第一步,本研究构建了海州湾鱼类群落的质量谱模型。本研究详述了数据收集和模型参数化的过程,以促进该模型在数据稀缺的生态系统中未来的应用。作为一个范例,研究展示了不同捕捞努力量对生态系统的影响,并采用一套生态指标监测其动态。群落生物量、多样性指数、W指数,大鱼指数(LFI),平均体重和群落质量谱斜率对捕捞压力的响应呈非线性,最大的捕捞强度并非总是对鱼类群落产生最强的影响。本文强调了构建谱模型在生态研究中的的价值和可行性,并讨论了模型的局限性和改进的可能。本研究旨在促进质量谱模型的广泛应用以更好地支持基于生态系统的渔业管理。     

Tone generation on a hydrofoil of a high-speed ship

Experimental results of hydrofoil singing on a full-scale passenger ship are reported. It is proposed that hydrodynamic generation of a tone is caused by self-excited oscillation of a foil trailing edge. The natural frequency of the vibrating structure as well as the frequency of the external force are estimated. A lift-oscillator model is applied for modeling purposes. One effective method of eliminating the hydrofoil singing is discussed.     

Forces on a circular cylinder near a plane wall

The drag and lift force are measured on circular cylinders fitted with end plates in a wind tunnel. The gap between the cylinder and the wall, G, the thickness of the turbulent boundary layer along the wall, δ, and the Reynolds number, Re, are varied in the following ranges: 0 < G/D < 2, 0.12 < δ/D < 0.97 and 4.8 × 10⁴ Re 3 × 10⁵. The lift and drag coefficients are presented in terms of a new variable G/δ.

It is found that the lift coefficient is governed by the gap to diameter ratio G/D while the drag coefficient is dominated by the ratio of gap to thickness of the boundary layer, G/δ.