山西乡宁—吉县地区黄土高边坡可靠度研究

在山西乡宁—吉县地区实测了7个具有代表性的自然极限状态黄土高边坡断面,建立边坡地层结构模型;选取研究区合理的黄土物理力学参数,并分地层年代对10个典型工点的黄土强度参数内聚力和内摩擦角的变异性进行分析;选取6组典型的强度参数变异系数组合,基于Monte Carlo法进行可靠度模拟,评价该区边坡稳定性;采用自然类比法进行边坡设计.结果表明:边坡失效概率随坡高的变化趋势一致,均是中等坡高(49.8m)的边坡失效概率较大,低坡和高坡的失效概率较低;当变异系数较小时,边坡失效概率对坡高和坡度的变化敏感,而当变异系数较大时,边坡失效概率对坡高和坡度的变化不敏感;当坡型一定、强度参数变异系数较小时,边坡的稳定系数基本不变,而当参数变异系数超过某一界限时,稳定系数随变异系数的增大而增大,二者存在非线性相关关系;研究区黄土边坡处于基本稳定状态,但其失效概率最大达69.3%,平均21.1%,介于20%~30%的比例为33.3%,大于30%的比例为14.3%,可靠度指标介于-0.5~8.5,其中小于2.7的比例为88.1%;对于坡高约为50m的黄土高边坡,若取30%作为可接受失效概率,边坡坡度需降至45°以下,如果期望可接受失效概率在10%以内,则坡度不宜超过34°.     

某高速公路滑坡的数值模拟及后缘坡体稳定性分析

通过对诸永高速公路台州段1#滑坡(K120 085～K120 169)工程地质特征的分析,指出沿线区存在很多因修建公路引发的工程滑坡问题,然后采用边坡稳定性FLAC/Slope分析软件,对滑坡滑动前、后工况下稳定性进行数值模拟,并对滑移后的后缘坡体稳定性进行了数值分析.剪应变率云图和稳定性分析结果表明,滑动后的后缘坡体仍处于不稳定状态,又形成了新的滑坡体.     

物探在滑坡勘查中的应用

一、梅河高速公路17标段k111＋300边坡滑坡体的地质特征 1．工程地质概况 梅河高速公路17标K111＋300边坡属构造剥蚀中低山区，山谷多呈“V”字形，地形坡度25°～35°。边坡区地层岩性主要是泥盆系（D）片岩和石英岩，变晶结构，千枚状一薄层状构造，     

公路弃土场边坡的稳定影响因素敏感性分析

以日照市岚山区某弃土场为研究对象,通过对现场调研并采样开展直剪试验,在压实度分别为90%、92%和95%的情况下取得不同的黏聚力c和内摩擦角φ值,通过MIDAS GTS NX进行数据模拟,选取MohrCoulomb模型,采用有限元强度折减法(SRM)算出边坡的等效应变塑性区及安全系数,以此分析边坡稳定性。利用数值模拟的结果,分别绘制坡高、坡比与安全系数的关系图,归类分析不同坡高和坡度对边坡稳定性系数的变化规律。通过边坡稳定影响因素的敏感性分析,分析影响边坡稳定性各因素与边坡安全系数之间的相关性,即分析各因素的变化对于边坡安全系数的影响程度。     

软硬互层顺层岩质边坡破坏试验

软硬互层结构的顺层岩质边坡破坏类型复杂、难于防治, 针对此类边坡地质灾害易发、多发的问题, 从坡面角度、岩层倾向及组合形式、节理分布等方面进行了研究。边坡物理模型试验是揭示边坡变形破坏机理的重要手段, 基于相似理论, 以重庆市万州区孙家滑坡为工程依托, 根据滑坡区地质勘探报告设计了室内边坡物理模型试验; 试验通过顶升模型箱模拟重力加载来探究顺层岩质边坡发生破坏时, 前缘坡角和软弱夹层倾角之间的关系; 结合有限元分析软件Plaxis 2D对物理模型进行了多组数值模拟试验, 以验证软硬互层顺层岩质边坡破坏机制。试验结果表明: 对于顺层岩质边坡, 当软弱夹层的倾角在22°左右, 前缘开挖坡角58°左右时, 顺层岩质边坡容易发生滑动, 滑动面为后缘节理面和软弱夹层的贯通面。因此, 顺层岩质边坡稳定性受层面和节理面密度的控制, 当边坡含多层软弱层面时, 易沿层面和后缘节理贯通面发生破坏, 随着软弱面层数增加, 边坡稳定系数逐渐降低。研究成果可以为公路开挖切坡导致的顺层岩质边坡失稳机理研究及其稳定性评价提供理论依据, 为顺层岩质边坡失稳的预测预报提供支撑。      

基于多源数据的谭家湾滑坡变形机制及稳定性评价

针对2016年5月发生于秭归县西北部的谭家湾滑坡,结合卫星遥感影像、现场勘查资料以及历史资料等多源数据,初步明确了滑坡的影响区域、特征及发生时序;综合采用钻探、槽探、物探等手段,开展室内外相关实验,明确了滑坡区的地层特性以及岩土体物理力学性质指标,通过分析该区裂缝位移及GPS数据,对该边坡的变形机制进行了探讨,并对该区稳定性进行了评价。结果表明:①谭家湾滑坡属于不规则"圈椅形"中型松散层的水库下降型滑坡,滑坡区的地表形态、地质构造及岩性等因素决定了滑坡的形成和发育,库水位和降雨的共同作用激励了滑坡的变形;②滑坡根据时序共分为3级滑体,总体呈现多次、多层、相互影响的演化特点,第三级滑体具有牵引式特征;③滑坡体内地下水位随库水位下降而下降,但下降速率缓于库水位,随之坡体内水力梯度和渗透力显著变大,此时碰到强降雨,将会导致坡体地下水赋存,岩土体软化,加剧滑坡变形,须施加必要的防护措施。④稳定性分析表明,该滑坡现处于临界稳定状态,一旦发生降雨和库水位变化,局部段可能发生失稳滑动。      

鸭塘水库红层顺层缓倾滑坡形成机制分析与稳定性评价

红层在我国分布广泛,其边坡稳定性是工程建设中经常面临的问题。红层通常孕育顺层缓倾滑坡地质灾害,具有规模大、隐蔽性强、成灾机理多样等特点。本文以醴陵市鸭塘水库滑坡为例,对其形成机制进行了分析,对其稳定性进行了评价。评价结果表明水库长期渗水是该滑坡发展的一个重要因素,其稳定性与后缘裂隙贯通率、滑带泥化率及后缘裂隙充水高度密切相关,超过临界值,坡体将会失稳。对以后红层区库区选址、设计蓄水位确定、防渗处理工作具有一定指导意义。     

黄土区滑坡研究中地形因子的选取与适宜性分析

黄土高原是中国生态较为脆弱的地区,也是滑坡发育的地层之一。黄土滑坡发育是孕灾环境、致灾因子和承灾体等多种因素联合作用的结果,其中作为重要孕灾环境因素的地形因子的选取是黄土滑坡风险研究的基础。本文选取黄土滑坡灾害多发的甘谷县作为研究区,综合利用敏感性指数、确定性系数和相关系数方法进行地形因子在滑坡灾害研究中的适宜性分析,得出以下结论：基于确定性系数法、敏感性分析模型和相关系数法,最终筛选出适宜于本区域滑坡灾害评价的地形因子为：坡度、坡度变率、坡形和地表粗糙度;确定性系数法、敏感性分析模型都基于分析单一因子与滑坡之间的关系进行致灾因子选取,忽视地形因子之间的相关性。实验结果表明,研究区稳定性较差的区域与已发生滑坡灾害分布数量具有较好的对应关系,并深入分析了滑坡与地形因子分级范围的关系,发现地形因子分级范围对地质灾害风险研究具有重要的影响,是导致部分区域的差异性主要原因之一。实地调查发现,河网切割密度及人类工程活动也对研究区危险性具有重要的控制作用,是重要的地形因素。     

南水北调西线叶青—勒那曲引水线工程地质条件分段评价

叶青—勒那曲引水线路根据地质构造、地貌特征、物理地质现象,共划分六个区段。德曲段:山脊寒冻风化碎石坡型,山坡融冻泥流及顺河断层发育;解吾曲下段:冻土沼泽发育,南北构造活动较强烈,区域稳定性及边坡稳定性较差;解吾曲上游段;山区和丘陵区断裂发育,在喜山末期有强烈的活动,滑坡、冰丘等不良地质现象极为发育;玛尕曲—洛曲南段:厚层地下冰发育,近期活动断裂明显;洛曲南岸—多曲东岸段:缓坡区有厚层地下冰,多年冻土布满全段;多曲东岸—万龙湾尕玛下游段:近代断裂活动明显,区域稳定性较差。     

降雨促发黄土滑坡的启动机制模拟

黄土滑坡和降雨关系尤为密切。为深入研究降雨入渗对滑坡的促发作用,在对陕西西安地区“9·17”灞桥滑坡现场勘察的基础上,利用数值模拟方法系统研究了黄土边坡在降雨入渗条件下土体相关物理力学指标的变化响应特征及时空分布规律;从滑动面安全系数变化的角度分析了边坡的失稳过程,并揭示了该类滑坡的启动机制。结果表明：(1)降雨入渗首先引起坡面土体的基质吸力逐渐降低,而且不同分布位置的降幅不同;(2)滑坡启动前,坡体的高体积含水量范围随降雨明显扩大,且体积含水量表现出从古土壤层向邻近黄土层递减的规律;(3)边坡的水平方向位移自坡面中部向坡体的上下部呈放射状递减特征,垂直方向位移由上至下逐渐减小,而临界滑动面的安全系数也随降雨入渗过程逐步递减;(4)节理处土体的孔隙水压力和体积含水量的变化响应时间及幅度都早于且强于坡体其他区域,坡体内最大剪应变的区域分布与坡面基本平行,模拟结果与原型滑坡一致;(5)基于黄土独特的水敏性、地质构造和人类工程活动等诱因的影响,加上节理裂隙为水的入渗和运移提供了优势通道,降雨加速了黄土潜蚀和坡体结构破坏过程,改变了边坡内部应力场、位移场和水文地质条件,进而促发了滑坡。     

西安白鹿塬北缘黄土边坡稳定的可靠度分析

在西安白鹿塬北缘实测了14个黄土自然边坡断面,建立了地质模型,通过采样测试并收集已有的测试资料,获得了各时代黄土地层的物理力学参数,将Morgenstern-Price法稳定性计算公式作为极限状态方程,分别采用Monte-Carlo法和Duncan法进行了边坡稳定的可靠度分析。结果表明:采用Monte-Carlo法和Duncan法得到的14个边坡稳定系数分别为1.11～1.41和1.09～1.33,显示这些边坡处于基本稳定—稳定状态;采用上述两种方法得到的边坡可靠指标分别为0.56～1.79和0.39～1.60,得到的失效概率分别为3.4%～29.0%和5.5%～34.8%,并且共有75%的边坡失效概率大于10%,失效可能性较大。统计结果表明:白鹿塬区边坡的坡高和坡度存在负相关性。低而陡的边坡潜在最危险滑面剪出口较高,失效概率较小;坡高达到50m及以上时,边坡高而缓,剪出口较低,失效概率较大,其中河流下切深,有N2泥岩出露的极高边坡,稳定性最差。Duncan法求解的稳定系数略小于Monte-Carlo法求得的结果,而前者求解的失效概率略大于后者,两种方法计算结果较为接近。由于Duncan法理论简单,计算量小,更宜于在实际工程中应用。     

Inversion analysis of the shear strength parameters for a high loess slope in the limit state

It is difficult to obtain reliable shear strength parameters for the stability analysis and evaluation of high loess slopes.Hence,this paper determines slope elements and physical parameter of 79 slopes with heights of[40,120]m based on the measured loess slopes in the Ganquan and Tonghuang subregions of northern Shaanxi Province,China.In the limit state of the loess slope(stability factor Fs is 1.0),a fitting equation for the slope height and width is established.Then,the model is developed by stability analysis software-SLOPE/W,and the comprehensive shear strength parameters corresponding to different slope heights of the high slope in the study area are obtained by inversion using the Morgenstern-Price method.The results show that when the height of the slope increases,the cohesion c increases in the soil,and the internal friction angle j decreases.This change is consistent with the characteristics reflected in the composition and physical properties of the slopes,and the comprehensive strength parametric curves are very similar between the Ganquan subregion and the Tonghuang subregion.A landslide that occurred in Miaodian-zaitou of Jingyang County,Shaanxi Province,is selected to verify this inversion method,and the results show that the calculated shear strength parameters of the inversion are consistent with the measured value of the actual slope.     

Mechanism of slope failure in loess terrains during spring thawing

Slope failure in loess terrains of Northern China during spring thawing period is closely related to the freeze-thaw cycling that surface soils inevitably experienced. Field surveys were carried out on natural and artificial slopes in thirteen surveying sites located in the Northern Shaanxi, the center of Loess Plateau, covering five characteristic topographic features including tablelands, ridges, hills, gullies and valleys. Based on the scale that is involved in freeze-thaw cycling, the induced failures can be classified into three main modes, i.e., erosion, peeling and thaw collapse, depending on both high porosity and loose cementation of loess that is easily affected. Model tests on loess slopes with gradients of 53.1°, 45.0° and 33.7° were carried out to reveal the heat transfer, water migration and deformation during slope failure. The surface morphology of slopes was photographed, with flake shaped erosion and cracks noted. For three slope models, time histories for the thermal regime exhibit three obvious cycles of freeze and thaw andthe maximum frost depth develops downwards as freeze-thaw cycling proceeds. Soil water in the unfrozen domain beneath was migrated towards the slope surface, as can be noticed from the considerable change in the unfrozen water content, almost synchronous with the variation of temperature. The displacement in both vertical and horizontal directions varies over time and three obvious cycles can be traced. The residual displacement for each cycle tends to grow and the slopes with higher gradients are more sensitive to potentially sliding during freeze-thaw cycling.     

Relationships between landslide types and topographic attributes in a loess catchment, China

Topographic attributes have been identified as the most important factor in controlling the initiation and distribution of shallow landslides triggered by rainfall.As a result,these landslides influence the evolution of local surface topography.In this research,an area of 2.6 km 2 loess catchment in the Huachi County was selected as the study area locating in the Chinese Loess Plateau.The landslides inventory and landslide types were mapped using global position system(GPS) and field mapping.The landslide inventory shows that these shallow landslides involve different movement types including slide,creep and fall.Meanwhile,main topographic attributes were generated based on a high resolution digital terrain model(5 m × 5 m),including aspect,slope shape,elevation,slope angle and contributing area.These maps were overlaid with the spatial distributions of total landslides and each type of landslides in a geographic information system(GIS),respectively,to assess their spatial frequency distributions and relative failure potentials related to these selected topographic attributes.The spatial analysis results revealed that there is a close relation between the topographic attributes of the postlandsliding local surface and the types of landslide movement.Meanwhile,the types of landslide movement have some obvious differences in local topographic attributes,which can influence the relative failure potential of different types of landslides.These results have practical significance to mitigate natural hazard and understandgeomorphologic process in thick loess area.     

Multitemporal UAV-based photogrammetry for landslide detection and monitoring in a large area:a case study in the Heifangtai terrace in the Loess Plateau of China

With high spatial resolution,on-demand-flying ability,and the capacity for obtaining threedimensional measurements,unmanned aerial vehicle(UAV) photogrammetry is widely used for detailed investigations of single landslides,but its effectiveness for landslide detection and monitoring in a large area needs to be investigated.The Heifangtai terrace in the Loess Plateau of China is a loess terrace that is extremely susceptible to irrigation-induced loess landslides.This paper used UAV-based photogrammetry for a series of highresolution images spanning over 30 months for landslide detection and monitoring of the terrace with an area of 32 km~2.Dense and evenly distributed ground control points were established and measured to ensure the high accuracy of the photogrammetry results.The structure-from-motion(Sf M) technique was used to convert overlapping images into orthographic images,3D point clouds,digital surface models(DSMs) and mesh models.Using multitemporal differential mesh models,landslide vertical movements and potential landslides were detected and monitored.The results indicate that a combination of UAV-based orthophotos and differential mesh models can be used for flexible and accurate detection and monitoring of potential loess landslides in a large area.     

Eco-morphological characteristics of fern species for slope conservation

Degradation of slopes due to shallow landslide and the subsequent erosional processes are a big challenge on the application of soil bioengineering techniques; that is the use of plants as main structural components of a slope protection and conservation system. An optimal application of soil bioengineering techniques should include not only the technical factor of plants as structural components but also the ecology of species and the plant adaptations to disturbances, which is crucial if a longterm successful slope restoration system is intended. Ferns are a dominant understory vegetation species in the forest of Japan, but its characteristics and influences on the recovery of shallow landslide scars have not been fully studied yet. This study aims to find out the ecological characteristics of fern species through the calculation of ecological indicators and the quantification of the morphological features of specimens growing on disturbed and non-disturbed forest slopes in Japan. Gleichenia japonica was found as the vegetation species with biggest ecological indicators on both slopes. The analysis of morphological characteristics of the specimens growing on both sites showed that the development of the specimens is focused in below-ground characteristics. The pull-out force of Gleichenia japonica root system as an indicator of ecological adaptation to a constraint environment and morphological characteristics quality is influenced by height and root length according to the principal component analysis. The eco-morphological characteristics of species can be used as an indicator of an optimal element in soil bioengineering establishment for slope conservation proposes. The long and fibrous root system could be placed on forest roads, steep or small slopes where space limitation is an issue for the establishment of bigger species and if the slope conditions allow it, it can control soil losses due to rainfall and provide stability.     

基于DEM的黄土高原地形纹理概念模型

黄土高原“千沟万壑”的地貌形态,在多尺度空间下表现出显著自相似性,具有“局部无规则,宏观有规律”的纹理特征。目前,黄土高原地形纹理的提取方法及应用已经得到初步发展,但依然缺乏在理论层面的框架体系。本文在已有学者研究成果的基础上,限定黄土高原为研究范围,明确提出黄土高原地形纹理的概念模型,即内涵、特征、分类及表达。将内涵进行扩展,除已有的宏观形态地形纹理外,提出黄土典型地貌单元（黄土塬、梁、峁等）特征组合形成的地形纹理,以及黄土坡面坡度特征形成的地形纹理;指出以数字高程模型为主的数据表达将更有利于地形纹理的量化,特别是基于DEM派生的坡面地形因子能够扩展地形纹理的特征空间,丰富地形纹理分析的数据源;明确地形纹理的基本特征,分别是区域差异性、成因复杂性和尺度依赖性;构建划分体系,以地形纹理的基元显著性、纹理成因以及可视化形态进行类别划分。本文以期构建面向黄土高原的地形纹理概念模型,推动纹理分析方法在黄土高原的应用和发展。     

基于DEM提取坡谱信息的不确定性

坡谱是黄土高原地学分析新方法、新思路的探索。本文基于坡谱不确定性的概念及其过程分布模型的论述,以陕北黄土高原国家1∶10000和1∶50000DEM数据为基本信息源,分析了坡谱不确定性的产生原因、主要影响因素与影响规律,阐述了坡谱提取与应用中应注意的主要问题,为正确应用坡谱进行地学分析提供重要依据。     

Landslide Susceptibility Assessment of the Youfang Catchment using Logistic Regression

A detailed landslide susceptibility map was produced in the Youfang catchment using logistic regression method with datasets developed for a geographic information system(GIS).Known as one of the most landslide-prone areas in China, the Youfang catchment of Longnan mountain region,which lies in the transitional area among QinghaiTibet Plateau, loess Plateau and Sichuan Basin, was selected as a representative case to evaluate the frequency and distribution of landslides.Statistical relationships for landslide susceptibility assessment were developed using landslide and landslide causative factor databases.Logistic regression(LR)was used to create the landslide susceptibility maps based on a series of available data sources: landslide inventory; distance to drainage systems, faults and roads; slope angle and aspect; topographic elevation and topographical wetness index, and land use.The quality of the landslide susceptibility map produced in this paper was validated and the result can be used fordesigning protective and mitigation measures against landslide hazards.The landslide susceptibility map is expected to provide a fundamental tool for landslide hazards assessment and risk management in the Youfang catchment.