长距离GPS/BDS双系统网络RTK方法

基于区域参考站网的网络实时动态定位(real-time kinematic,RTK)方法是实现全球定位系统(global positioning system,GPS)、北斗卫星导航系统(BeiDou satellite navigation system,BDS)高精度定位的主要手段。研究了一种长距离GPS/BDS双系统网络RTK方法,首先采用长距离参考站网GPS/BDS多频观测数据确定宽巷整周模糊度,利用引入大气误差参数的参数估计模型解算GPS/BDS双差载波相位整周模糊度;然后按照长距离参考站网观测误差特性的不同,分类处理参考站观测误差,利用误差内插法计算流动站观测误差,以改正流动站GPS/BDS双系统载波相位观测值的观测误差;最后使用流动站多频载波相位整周模糊度解算方法确定GPS/BDS载波相位整周模糊度并解算位置参数。使用长距离连续运行参考站(continuously operating reference stations,CORS)网的实测数据进行实验,结果表明,该方法能够利用长距离GPS/BDS参考站网实现流动站的厘米级定位。     

长距离GPS/BDS参考站网多频载波相位整周模糊度解算方法

长距离网络RTK是实现GPS/BDS高精度实时定位的主要手段之一,其核心是长距离参考站网GPS/BDS整周模糊度的快速准确确定。本文提出了一种长距离GPS/BDS参考站网载波相位整周模糊度解算方法,首先利用GPS双频观测数据计算和确定宽巷整周模糊度,同时利用BDS的B2、B3频率观测值确定超宽巷整周模糊度。然后建立GPS载波相位整周模糊度和大气延迟误差的参数估计模型,附加双差宽巷整周模糊度的约束,解算双差载波相位整周模糊度,并建立参考站网大气延迟误差的空间相关模型。根据B2、B3频率的超宽巷整周模糊度建立包含大气误差参数的载波相位整周模糊度解算模型,利用大气延迟误差空间相关模型约束BDS双差载波相位整周模糊度的解算。克服了传统的使用无电离层组合值解算整周模糊度的不利影响。采用实测长距离CORS网GPS、BDS多频观测数据进行算法验证,试验结果证明该方法可实现长距离参考站网GPS/BDS载波相位整周模糊度的准确固定。     

Generation of differential GPS corrections along with performance of quality control

1　ＩｎｔｒｏｄｕｃｔｉｏｎＣｕｒｒｅｎｔｌｙ ,ｔｈｅｒｅａｌｒｅａｄｙｅｘｉｓｔｓｅｖｅｒａｌａｌｇｏｒｉｔｈｍｓｆｏｒｔｈｅｇｅｎｅｒａｔｉｏｎｏｆｄｉｆｆｅｒｅｎｔｉａｌｃｏｒｒｅｃｔｉｏｎｓ,ｆｏｒｉｎ ｓｔａｎｃｅ ,ｔｈｅａｌｇｏｒｉｔｈｍｂａｓｅｄｏｎｃａｒｒｉｅｒｆｉｌｔｅｒｅｄｃｏｄｅｏｂｓｅｒｖａｔｉｏｎｓ (ｖａｎＤｉｅｒｅｎｄｏｎｃｋ ,1 993 ;Ｌａｎｄａｕ ,1 993 )ａｎｄｔｈｅａｌｇｏｒｉｔｈｍｂａｓｅｄｏｎｃｏｄｅｏｂｓｅｒｖａｔｉｏｎｓａｎｄｓｅｑｕｅｎｔｉａｌｄｉｆｆｅｒｅ…     

Generation of differential GPS corrections along with performance of quality control

The DGPS technique can provide considerably better relative positioning accuracy than the stand-alone GPS positioning, but the improvement depends on the distance between the user and the reference station (spatial correlation), the latency of differential corrections (temporal correlation), and the quality of differential corrections. Therefore, how to correctly generate differential corrections as well as their pricision is very important to the DGPS positioning technique. This paper presents a new algorithm for generating differential GPS corrections. This algorithm directly uses code and carrier observations in the measurement model of a Kalman filter, so that it is possible to use a simple stochastic model and to use the standard algorithm of the Kalman filter. The algorithm accounts for biases like multipath errors and instrumental delays in code observations and it shows how differential corrections are differently affected by code biases when dual or single frequency data is used. In addition, the algorithm can be integrated with a real time quality control procedure. As a result, the quality of differential corrections can be guaranteed with a certain probability.     

BDS网络RTK中距离参考站整周模糊度单历元解算方法

提出了一种BDS网络RTK中距离(50~100 km)参考站间的双频载波相位整周模糊度单历元解算方法。该方法首先利用B1、B2载波相位整周模糊度间的线性关系选取B1、B2载波相位整周模糊度备选值。利用双频载波相位整周模糊度备选值计算双差电离层延迟误差,根据参考站各卫星电离层延迟误差间的空间关系,使用双差电离层延迟误差构建双差电离层延迟误差的线性计算模型。通过双差电离层延迟误差线性计算模型的建立搜索和确定B1、B2载波相位的整周模糊度。经CORS网实测数据试验算例的验证,该方法只需一个历元的观测数据即可确定参考站间双差B1、B2载波相位整周模糊度,且不受周跳影响。     

基准站观测数据加密方法及其在差分GNSS后处理中的应用

当基准站采样率低于流动站时,不能用常规差分全球卫星导航系统（Global Navigation Satellite System,GNSS）后处理方法得到流动站所有历元坐标。针对此问题,给出了基于精密单点定位（precise point positioning,PPP）模型构造基准站非采样点上虚拟观测值的方法。该方法将接收机钟差、对流层天顶湿延迟从观测值误差中分离出来,同消电离层模糊度一起进行估计,利用基准站真实坐标获得卫地距,在此基础上计算相邻两个观测历元的残差进而拟合历元间非采样点残差,与卫地距、各项估计误差一起生成虚拟观测值。该方法保持了虚拟观测值的误差特性,尤其是基准站与流动站间的共性误差。该方法仅加密基准站数据,对流动站没有影响。算例结果表明,基准站在采样间隔30 s范围内,使用该方法加密的虚拟观测值与真实值有较好的一致性,采样间隔分别为30 s、15 s、5 s的虚拟测码伪距和载波相位观测值偏差的标准中误差分别在0.2 m和1.2周左右、0.1 m和0.7周左右、0.05 m和0.2周左右;在30 s采样间隔情况下,按照该方法处理后仍能满足厘米级定位精度的要求。     

一种精确估计区域北斗接收机硬件延迟的方法

提出了一种精确估计区域北斗接收机硬件延迟(DCB)的方法。该方法不需要传统复杂的电离层模型,在已知一个参考站接收机硬件延迟的条件下,利用正常情况下电离层延迟量和卫星-接收机几何距离强相关这一特点,采用站间单差法来精确估计区域内BDS接收机的硬件延迟。试验结果表明,该方法单站估计的单站北斗接收机连续30d的硬件延迟RMS在0.3ns左右。通过GEO卫星双频观测值扣除已知卫星DCB和本文方法估计的接收机DCB,计算对应穿刺点一天的VTEC并和GIM格网内插结果并进行比对分析,二者大小和变化趋势均符合较好,进一步验证了本文提出的方法具有可靠性。     

Analysis of GPS RTK performance using external NOAA tropospheric corrections integrated with a multiple reference station approach

For high-accuracy geodetic applications, time-variable tropospheric propagation delay errors limit global positioning system real-time kinematic positioning accuracy. Potential improvements in positioning accuracy are evaluated by using the National Oceanic and Atmospheric Administration (NOAA) real-time tropospheric corrections (herein called NOAA model) within a multiple reference station network approach. The results are compared with those for modified Hopfield tropospheric model corrections, for six scenarios in three geographical regions in the U.S. National Geodetic Survey network of Continuously Operating Reference Stations, for baseline lengths of 60~150 km. Analyses are conducted at rover locations for relatively humid days, and misclosures for various double difference observations are computed; these observations include each frequency (L1 and L2) and three linear combinations [wide lane, ionosphere free (IF), and geometry free]. The effectiveness of the network approach is demonstrated, with overall performance improvements of 15 and 19%, using the modified Hopfield and the NOAA model, respectively. The IF linear combination, a measure of tropospheric and orbital errors, shows a 3% improvement for the NOAA model compared with the modified Hopfield model.     

Quality assessment of GPS rapid static positioning with weighted ionospheric parameters in generalized least squares

Precise GPS positioning requires the processing of carrier-phase observations and fixing integer ambiguities. With increasing distance between receivers, ambiguity fixing becomes more difficult because ionospheric and tropospheric effects do not cancel sufficiently in double differencing. A popular procedure in static positioning is to increase the length of the observing session and/or to apply atmospheric (ionospheric) models and corrections. We investigate the methodology for GPS rapid static positioning that requires just a few minutes of dual-frequency GPS observations for medium-length baselines. Ionospheric corrections are not required, but the ionospheric delays are treated as pseudo-observations having a priori values and respective weights. The tropospheric delays are reduced by using well-established troposphere models, and satellite orbital and clock errors are eliminated by using IGS rapid products. Several numerical tests based on actual GPS data are presented. It is shown that the proposed methodology is suitable for rapid static positioning within 50–70 km from the closest reference network station and that centimeter-level precision in positioning is feasible when using just 1 min of dual-frequency GPS data.     

SBAS星历改正数及UDRE参数生成算法分析

星基增强系统(satellite based augmentation system,SBAS)通过地球同步轨道卫星实时播发导航卫星星历改正数和完好性参数,以提升用户定位精度和完好性。采用最小方差法解算GPS星历改正数,利用卡方统计进行改正数完好性检核,并依据星历改正数方差-协方差信息计算SBAS用户差分距离误差(user differential range error,UDRE)和信息类型28(message type 28, MT28)等完好性参数。利用中国区域27个监测站的实测数据,首先以国际GNSS服务组织的精密轨道和钟差产品为参考解算星历改正数,结果表明,钟差改正精度优于0.1 m,轨道改正精度优于0.4 m;然后解算广播星历改正数,并生成UDRE和MT28参数,广播星历残余误差卡方检验值均小于告警门限,保证了改正数的完好性;最后利用生成的改正数进行SBAS定位解算,得到定位结果的水平精度优于0.7 m,垂直精度优于1.0 m,对比GPS单点定位,所提算法的水平和垂直方向精度分别提升了30%和40%。     

零基线约束的参考站间模糊度固定方法研究

论文提出一种GNSS零基线约束的参考站间模糊度快速固定方法,该方法基于“一天线+双接收机”设计进行参考站间模糊度固定。首先,利用两个参考站四台接收机观测值形成四对参考站间无电离层组合双差观测值。其次,结合无电离层组合观测值模糊度和宽巷整周模糊度进行卡尔曼滤波和N1模糊度实数解计算。然后在模糊度域内进行线性变换,单历元固定零基线模糊度;利用零基线模糊度约束解算四组参考站间模糊度中的一组模糊度。最后,利用固定的模糊度还原所有原始双差整周模糊度。实验证明:与传统参考站间模糊度固定方法比,充分利用了零基线模糊度固定的约束条件进行参考站间模糊度固定,加快了模糊度收敛速度,极大地提高了模糊度固定的速度和成功率。      

BDS参考站三频整周模糊度单历元确定方法

参考站载波相位整周模糊度的准确确定是实现BDS网络RTK定位的关键。本文研究了BDS参考站三频载波相位整周模糊度单历元确定方法。首先推导了参考站三频载波相位整周模糊度之间的多个整数线性关系,根据双频载波相位整周模糊度的整数线性关系,以及B1载波相位整周模糊度备选值,确定B1/B2和B1/B3载波相位整周模糊度的备选组合。然后利用不受误差影响的三频载波相位整周模糊度间整数线性关系,对整周模糊度备选值进行约束和确定。根据大气误差的空间相关性,采用以卫星高度角和方位角为依据的基准卫星选择方法,降低了对流层延迟误差残差对多频载波相位整周模糊度之间线性关系约束能力的影响。试验结果表明,本文方法能够实现参考站三频载波相位整周模糊度的单历元准确确定,且计算效率高,算法简单。     

一种北斗非差非组合长距离基准站模糊度解算方法

为了充分利用各频率观测值信息,提出了一种非差非组合的北斗卫星导航系统长距离基准站间整周模糊度解算方法。首先,直接利用不同频率的观测值建立误差观测方程,并采用随机游走策略估计相对天顶对流层湿延迟误差和电离层延迟误差,增加历元间的约束;然后,采用一种非差整周模糊度实时线性计算方法,依次得到基准站网当前历元所有卫星的非差整周模糊度,解决了在基准星变换时,模糊度需要承接或者重新进行法方程叠加的问题;最后,使用实测数据进行方法验证,结果表明,各基准站模糊度平均固定速度为20个历元（采样间隔1 s）,可快速实现基准站载波相位整周模糊度解算。由于所提方法充分利用了各频率观测值信息,避免了线性组合放大噪声对整周模糊度固定的影响,其模糊度固定成功率与无电离层组合法相比有较大的提高。     

基于单个GPS/BDS信标台增强的实时精密单点定位

随着IGS实时服务的推广,实时轨道、钟差产品可用于实时PPP;然而,在一些通讯条件差的地方,如偏远山区和广袤的海洋,差分信号的播发与接收仍然是实时PPP的障碍。文中提出一种基于单个GPS/BDS信标台的实时PPP定位方法:基站采用广播星历和无电离层伪距、相位观测值,实时估计耦合轨道、钟误差;单向通讯的方式播发给用户端,减小通讯量,提高用户端的定位性能。经过分别距参考站约200km和300km的流动站进行验证,通过约10~12min收敛,GPS/BDS组合可得到水平优于20cm的定位精度。本案验证了采用广播星历进行实时PPP的可行性,为海洋和偏远地区提供一种高精度定位方法。     

大范围网络RTK基准站间整周模糊度实时快速解算

网络RTK是目前实现高精度实时动态定位的重要手段之一,而网络RTK高精度定位的关键问题是基准站间整周模糊度的实时快速准确固定。对于大范围网络RTK,由于基准站间距离的增加,电离层延迟误差、对流层延迟误差和卫星轨道误差相关性降低,导致基准站间整周模糊度不能快速准确地固定,因此本文提出了一种大范围网络RTK基准站间整周模糊度固定算法。该算法首先利用L1、L2载波相位观测值和P1、P2伪距观测值解算基准站间的双差宽巷模糊度;然后采用Saastamoinen模型和Chao映射函数模型相结合解算双差对流层延迟误差,并将双差宽巷模糊度作为L1、L2双差载波相位整周模糊度的约束关系来确定L1、L2双差载波相位整周模糊度;最后采用CORS站的实测数据进行试验,并将本文的试验结果同GAMIT软件的解算结果进行比对,结果表明该算法可以快速准确地实现单历元双差载波相位整周模糊度的固定。     

Time-Relative Positioning with a Single Civil GPS Receiver

Time-relative positioning is a recent method for processing GPS phase observations. The operational method undertaken in this paper consists of the following steps: first, recording phase observations at a station of known coordinates; second, moving the GPS receiver to an unknown station (which can be located up to a few hundred meters away, dependint on what type of transportation – e. g., walking, motorcycle – is available) while continuously observing carrier phases; and, third, recording phase observations at a second station of unknown coordinates with a single GPS receiver. To obtain the position of the unknown station relative to the first (known) station, the processing method uses combined observations taken at two different epochs and two different stations with the same receiver. For this reason, the errors that vary between two epochs must be taken into account in an appropriate way, especially errors in satellite clock corrections and ephemerides, and errors related to tropospheric and ionospheric delays. Ionospheric modeling using IONEX files (the ionospheric maps calculated by the International GPS Service) was also tested to correct L1 phase observations. This method has been used to calculate short vectors with an accuracy of a few centimeters (for a processing interval of 30 s) using a single civil GPS receiver. ? 2001 John Wiley & Sons, Inc.     

广域差分的全矢量法

针对广域差分改正矢量的组成元素集之一的电离层模型参数集,分别用Klobuchar模型和Georgiadou模型进行了分析和比较,详细推演了广域差分改正矢量估计的全矢量法.在统一的数学模型中给出了统一解算卫星星历误差、卫星钟差和广域差分基准站时钟误差的计算公式;对理想状态下的模型参数、基准站和跟踪的卫星的数量关系进行了探讨.     

基于映射函数网络RTK的大气误差内插估计模型

在比较分析已有内插模型的基础上,以卫星高度角、参考站高程、距离为变量,以大气映射函数为基本模型,提出了一种新的适用于高程差异大的大气误差内插模型。利用江苏连续运行参考站系统部分参考站数据,采用不同的内插模型进行处理、比较与分析。结果表明,对于高程差异大、卫星高度角小的用户站,映射函数估计方法、低阶曲面模型能够准确地估计出其与主参考站之间双差对流层误差,其最大均方差不超过2cm;映射函数估计双差电离层误差方法与低阶曲面模型、线性内插模型的估计精度相当。在以上4种方法的比较中,距离线性内插模型的估计精度最差,将近5cm。     

Single-frequency single-site VTEC retrieval using the NeQuick2 ray tracer for obliquity factor determination

A single-frequency single-site GPS/Galileo algorithm for retrieval of absolute total electron content is implemented. A single-layer approximation of the ionosphere is used for data modeling. In addition to a standard mapping function, the NeQuick model (version 2) of the ionosphere is now applied to derive improved mapping functions. This model is very attractive for this purpose, because it implements a ray tracer. We compare the new algorithm with the old one using an effective global height of the ionosphere of 450 km. Combined IGS IONEX gridded data sets serve as reference data. On global average, we find a small improvement of 1 % in precision (standard deviation) of the NeQuick2 mapping method versus the conventional approach on global average. A site-by-site comparison indicates an improvement in the precision for 34 % of the 44 sites under investigation. The level of improvement for these stations is 0.5 TECU on average. No improvement was observed for 41 % of the sites. Further comparisons of the single (code ranges and carrier phases) versus dual-frequency (carrier phases only) single site algorithm show that dual-frequency VTEC estimation is more accurate for the majority of the stations, but only in the range of 0.3 TECU (2.6 %) in average.     

Precise estimation of residual tropospheric delays using a regional GPS network for real-time kinematic applications

 A new method called Trop_NetAdjust is described to predict in real time the residual tropospheric delays on the GPS carrier phase observables using the redundant measurements from a network of GPS reference stations. This method can not only enhance the effectiveness and reliability of real-time kinematic users within the network, but also provide a valid approach to tropospheric parameter variation forecasting. Trop_NetAdjust is theoretically based upon LS prediction criteria and enables the prediction of residual tropospheric delays remaining after a standard model has been applied to the raw GPS measurements. Two cases are analyzed, namely a first case when the delay is required for an existing satellite at a new point within the network and a second case when the delay is required for a new satellite. Field tests were conducted using data collected in a network of 11 reference stations covering a 400×600 km region in southern Norway. The results were analyzed in the measurement domain (ionospheric-free double-difference residuals) and showed improvements of 20 to 65% RMS errors using Trop_NetAdjust. The estimates of the Trop_NetAdjust prediction accuracy were also obtained using the covariance analysis method. The agreement was consistently better than 30% when compared with data from a real network. Received: 28 February 2000 / Accepted: 9 January 2001